U-Boot SPL 2011.09 (Mar 18 2014 - 15:08:14) Texas Instruments Revision detection unimplemented Sandia Pin Configuration is setting up Sandia Pin config is complete.... Critical Link AM335X Dev Kit PLL configuration complete OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2011.09 (Mar 18 2014 - 15:08:14) I2C: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: HW ECC Hamming Code selected 256 MiB MMC: OMAP SD/MMC: 0 *** Warning - bad CRC, using default environment Net: cpsw Hit any key to stop autoboot: 3  2  1  0 SD/MMC found on device 0 reading uenv.txt 1711 bytes read Loaded environment from uenv.txt Importing environment from mmc ... reading uImage 3705872 bytes read ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0-00217-g3c4aa5c-dirty Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3705808 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0-00217-g3c4aa5c-dirty (root@dlinux) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #13 Tue Mar 18 15:13:44 PDT 2014 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: mityarm335x [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 251284k/251284k available, 10860k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0746000 (7416 kB) [ 0.000000] .init : 0xc0746000 - 0xc0784000 ( 248 kB) [ 0.000000] .data : 0xc0784000 - 0xc081d620 ( 614 kB) [ 0.000000] .bss : 0xc081d644 - 0xc085d074 ( 255 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000152] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144) [ 0.058044] pid_max: default: 32768 minimum: 301 [ 0.058166] Security Framework initialized [ 0.058258] Mount-cache hash table entries: 512 [ 0.058624] CPU: Testing write buffer coherency: ok [ 0.078338] omap_hwmod: gfx: failed to hardreset [ 0.094329] omap_hwmod: pruss: failed to hardreset [ 0.095672] print_constraints: dummy: [ 0.096069] NET: Registered protocol family 16 [ 0.098297] OMAP GPIO hardware version 0.1 [ 0.100982] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.103515] omap_i2c.3: alias fck already exists [ 0.103790] omap_i2c.2: alias fck already exists [ 0.104492] Registering mcspi 1 [2] [ 0.104553] omap2_mcspi.1: alias fck already exists [ 0.104766] Registering mcspi 2 [2] [ 0.104797] omap2_mcspi.2: alias fck already exists [ 0.105072] edma.0: alias fck already exists [ 0.105072] edma.0: alias fck already exists [ 0.105102] edma.0: alias fck already exists [ 0.108428] baseboard_init [MityARM-335x DevKit]... [ 0.108428] Configure Ethernet RGMII PINs... [ 0.108642] Configure SMSC LAN8820 PHY chip... [ 0.108642] ------------[ cut here ]------------ [ 0.108673] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x58/0xd4() [ 0.108703] autorequest GPIO-53 [ 0.108703] Modules linked in: [ 0.108703] Backtrace: [ 0.108734] [] (dump_backtrace+0x0/0x10c) from [] (dump_stack+0x18/0x1c) [ 0.108764] r6:00000065 r5:c01eb61c r4:cf81bf00 r3:c07a6750 [ 0.108795] [] (dump_stack+0x0/0x1c) from [] (warn_slowpath_common+0x54/0x6c) [ 0.108825] [] (warn_slowpath_common+0x0/0x6c) from [] (warn_slowpath_fmt+0x38/0x40) [ 0.108825] r8:cf8044d8 r7:40000013 r6:00000035 r5:cf8044d8 r4:c084aabc [ 0.108856] r3:00000009 [ 0.108856] [] (warn_slowpath_fmt+0x0/0x40) from [] (gpio_ensure_requested+0x58/0xd4) [ 0.108886] r3:00000035 r2:c06b68dc [ 0.108886] [] (gpio_ensure_requested+0x0/0xd4) from [] (gpio_direction_output+0xa0/0x160) [ 0.108917] r6:c084aabc r5:cf81a000 r4:00000015 r3:00000020 [ 0.108947] [] (gpio_direction_output+0x0/0x160) from [] (baseboard_init+0x74/0x464) [ 0.108947] [] (baseboard_init+0x0/0x464) from [] (do_one_initcall+0x40/0x184) [ 0.108978] r5:cf81a000 r4:c081d680 [ 0.109008] [] (do_one_initcall+0x0/0x184) from [] (kernel_init+0x80/0x11c) [ 0.109008] [] (kernel_init+0x0/0x11c) from [] (do_exit+0x0/0x66c) [ 0.109039] r5:c07467d8 r4:00000000 [ 0.109100] ---[ end trace 1b75b31a2719ed1c ]--- [ 0.109313] omap_hsmmc.0: alias fck already exists [ 0.109771] omap_hsmmc.2: alias fck already exists [ 0.110748] da8xx_lcdc.0: alias fck already exists [ 0.111267] d_can.0: alias fck already exists [ 0.111511] d_can.1: alias fck already exists [ 0.111785] Configuring audio... [ 0.111846] Registering mcasp[1] [ 0.111877] davinci-mcasp.1: alias fck already exists [ 0.112487] omap_i2c.1: alias fck already exists [ 0.112701] WLAN GPIO Info.. IRQ = 186 WL_EN = 100 BT_EN = -22 [ 0.112731] Bluetooth not Enabled! [ 0.112792] baseboard_setup_wlan: finished [ 0.112854] ------------[ cut here ]------------ [ 0.112884] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x58/0xd4() [ 0.112884] autorequest GPIO-54 [ 0.112884] Modules linked in: [ 0.112915] Backtrace: [ 0.112945] [] (dump_backtrace+0x0/0x10c) from [] (dump_stack+0x18/0x1c) [ 0.112945] r6:00000065 r5:c01eb61c r4:cf81bf00 r3:c07a6750 [ 0.112976] [] (dump_stack+0x0/0x1c) from [] (warn_slowpath_common+0x54/0x6c) [ 0.113006] [] (warn_slowpath_common+0x0/0x6c) from [] (warn_slowpath_fmt+0x38/0x40) [ 0.113006] r8:cf8044d8 r7:60000013 r6:00000036 r5:cf8044d8 r4:c084aac8 [ 0.113037] r3:00000009 [ 0.113037] [] (warn_slowpath_fmt+0x0/0x40) from [] (gpio_ensure_requested+0x58/0xd4) [ 0.113067] r3:00000036 r2:c06b68dc [ 0.113067] [] (gpio_ensure_requested+0x0/0xd4) from [] (gpio_direction_output+0xa0/0x160) [ 0.113098] r6:c084aac8 r5:c04ccb90 r4:00000016 r3:00000020 [ 0.113128] [] (gpio_direction_output+0x0/0x160) from [] (baseboard_init+0x3a8/0x464) [ 0.113159] [] (baseboard_init+0x0/0x464) from [] (do_one_initcall+0x40/0x184) [ 0.113159] r5:cf81a000 r4:c081d680 [ 0.113189] [] (do_one_initcall+0x0/0x184) from [] (kernel_init+0x80/0x11c) [ 0.113220] [] (kernel_init+0x0/0x11c) from [] (do_exit+0x0/0x66c) [ 0.113220] r5:c07467d8 r4:00000000 [ 0.113220] ---[ end trace 1b75b31a2719ed1d ]--- [ 0.137725] bio: create slab at 0 [ 0.139953] SCSI subsystem initialized [ 0.141998] usbcore: registered new interface driver usbfs [ 0.142333] usbcore: registered new interface driver hub [ 0.142547] usbcore: registered new device driver usb [ 0.142700] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3 [ 0.143005] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0 [ 0.156616] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.157592] tps65910 3-002d: JTAGREVNUM 0x1 [ 0.159973] print_constraints: VRTC: [ 0.161437] print_constraints: VIO: at 1800 mV [ 0.163696] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal [ 0.165954] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.166961] print_constraints: VDD3: 5000 mV [ 0.168395] print_constraints: VDIG1: at 1800 mV [ 0.169799] print_constraints: VDIG2: at 1800 mV [ 0.171234] print_constraints: VPLL: at 1800 mV [ 0.172637] print_constraints: VDAC: at 1800 mV [ 0.174072] print_constraints: VAUX1: at 1800 mV [ 0.175506] print_constraints: VAUX2: at 3300 mV [ 0.176910] print_constraints: VAUX33: at 3300 mV [ 0.178344] print_constraints: VMMC: at 3300 mV [ 0.178863] tps65910 3-002d: No interrupt support, no core IRQ [ 0.195983] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 0.215667] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.216827] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.218200] cfg80211: Calling CRDA to update world regulatory domain [ 0.219390] Switching to clocksource gp timer [ 0.235321] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.235534] musb-hdrc musb-hdrc.0: dma type: pio [ 0.236419] musb-hdrc musb-hdrc.0: USB OTG mode controller at d081c000 using PIO, IRQ 18 [ 0.236602] musb-hdrc musb-hdrc.1: dma type: pio [ 0.236999] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.237091] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 0.237213] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.237213] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.237243] usb usb1: Product: MUSB HDRC host driver [ 0.237243] usb usb1: Manufacturer: Linux 3.2.0-00217-g3c4aa5c-dirty musb-hcd [ 0.237274] usb usb1: SerialNumber: musb-hdrc.1 [ 0.238037] hub 1-0:1.0: USB hub found [ 0.238067] hub 1-0:1.0: 1 port detected [ 0.238616] musb-hdrc musb-hdrc.1: USB OTG mode controller at d081e800 using PIO, IRQ 19 [ 0.239074] NET: Registered protocol family 2 [ 0.239288] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.239685] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.239837] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.239929] TCP: Hash tables configured (established 8192 bind 8192) [ 0.239959] TCP reno registered [ 0.239959] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.239990] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.240173] NET: Registered protocol family 1 [ 0.240447] RPC: Registered named UNIX socket transport module. [ 0.240478] RPC: Registered udp transport module. [ 0.240478] RPC: Registered tcp transport module. [ 0.240478] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.240692] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.252471] VFS: Disk quotas dquot_6.5.2 [ 0.252532] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.253082] msgmni has been set to 490 [ 0.253906] io scheduler noop registered [ 0.253936] io scheduler deadline registered [ 0.253997] io scheduler cfq registered (default) [ 0.254974] _regulator_get: tps6116x supply vlcd not found, using dummy regulator [ 0.257934] tps6116x tps6116x: registered backlight controller [ 0.258483] DA8XX FB - options = bpp=16 [ 0.258605] da8xx_lcdc da8xx_lcdc.0: GLCD: Found 800x600 panel [ 0.259704] DA8XX FB: 1024 x 768 16 bpp [ 0.275451] Console: switching to colour frame buffer device 128x48 [ 0.285736] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.287597] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 1.316253] console [ttyO0] enabled [ 1.320709] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 [ 1.328430] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 [ 1.336181] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 1.343902] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 1.351593] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 [ 1.368988] brd: module loaded [ 1.377258] loop: module loaded [ 1.380737] i2c-core: driver [tsl2550] using legacy suspend method [ 1.387084] i2c-core: driver [tsl2550] using legacy resume method [ 1.393432] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write [ 1.406097] MityARM-335x: Part Number = 3359-GX-226-RC [ 1.411376] MityARM-335x DevKit: factory_config_callback [ 1.417419] Configuring 256MB NAND device [ 1.422302] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 1.427246] Registering NAND on CS0 [ 1.433746] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes) [ 1.439239] Creating 1 MTD partitions on "spi_flash": [ 1.444458] 0x000000000000-0x000000800000 : "NOR User Defined" [ 1.452545] omap2-nand driver initializing [ 1.457092] ONFI flash detected [ 1.460479] ONFI param page 0 valid [ 1.464050] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP) [ 1.472320] Creating 8 MTD partitions on "omap2-nand.0": [ 1.477783] 0x000000000000-0x000000020000 : "SPL" [ 1.484039] 0x000000020000-0x000000040000 : "SPL.backup1" [ 1.490936] 0x000000040000-0x000000060000 : "SPL.backup2" [ 1.497772] 0x000000060000-0x000000080000 : "SPL.backup3" [ 1.504669] 0x000000080000-0x000000260000 : "U-Boot" [ 1.511901] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.518707] 0x000000280000-0x000000780000 : "Kernel" [ 1.527221] 0x000000780000-0x000010000000 : "File System" [ 1.635620] OneNAND driver initializing [ 1.639862] INIT SMSC PHY. [ 1.643249] SMSC lan8820_driver status: 0 [ 1.647613] CAN device driver interface [ 1.651580] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.657958] d_can d_can.0: device registered (irq=52, irq_obj=53) [ 1.664916] d_can d_can.1: device registered (irq=55, irq_obj=56) [ 1.720214] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.726562] davinci_mdio davinci_mdio.0: detected phy mask fffffffe [ 1.733489] am335x_lan8820_phy_fixup 7c0ec here addr = 0 [ 1.739288] davinci_mdio.0: probed [ 1.742828] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8820 [ 1.751007] usbcore: registered new interface driver cdc_ether [ 1.757141] usbcore: registered new interface driver cdc_subset [ 1.763305] Initializing USB Mass Storage driver... [ 1.768585] usbcore: registered new interface driver usb-storage [ 1.774749] USB Mass Storage support registered. [ 1.779571] gadget: using random self ethernet address [ 1.784973] gadget: using random host ethernet address [ 1.790924] usb0: MAC 1a:3d:56:b7:98:d9 [ 1.794860] usb0: HOST MAC 6a:0f:d5:2e:f9:f8 [ 1.799316] gadget: Ethernet Gadget, version: Memorial Day 2008 [ 1.805541] gadget: g_ether ready [ 1.809020] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 1.814544] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2 [ 1.822265] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.829223] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.836669] usb usb2: Product: MUSB HDRC host driver [ 1.841766] usb usb2: Manufacturer: Linux 3.2.0-00217-g3c4aa5c-dirty musb-hcd [ 1.849121] usb usb2: SerialNumber: musb-hdrc.0 [ 1.854583] hub 2-0:1.0: USB hub found [ 1.858459] hub 2-0:1.0: 1 port detected [ 1.863708] mousedev: PS/2 mouse device common for all mice [ 1.870513] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 [ 1.879577] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0 [ 1.892608] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc1 [ 1.900512] i2c /dev entries driver [ 1.905029] Linux media interface: v0.10 [ 1.909271] Linux video capture interface: v2.00 [ 1.914550] usbcore: registered new interface driver uvcvideo [ 1.920562] USB Video Class driver (1.1.1) [ 1.928863] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.937500] cpuidle: using governor ladder [ 1.942352] cpuidle: using governor menu [ 1.952941] usbcore: registered new interface driver usbhid [ 1.958770] usbhid: USB HID core driver [ 1.963806] usbcore: registered new interface driver snd-usb-audio [ 1.992736] tlv320aic26-codec spi1.1: Probing AIC26 SoC CODEC driver [ 2.011291] asoc: tlv320aic26-hifi <-> davinci-mcasp.1 mapping ok [ 2.018890] ALSA device list: [ 2.022033] #0: MityARM-335X DevKit [ 2.025848] oprofile: hardware counters not available [ 2.031097] oprofile: using timer interrupt. [ 2.035583] nf_conntrack version 0.5.0 (3926 buckets, 15704 max) [ 2.042388] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.048065] TCP cubic registered [ 2.051452] NET: Registered protocol family 17 [ 2.056121] can: controller area network core (rev 20090105 abi 8) [ 2.062652] NET: Registered protocol family 29 [ 2.067352] can: raw protocol (rev 20090105) [ 2.071807] can: broadcast manager protocol (rev 20090105 t) [ 2.077758] lib80211: common routines for IEEE802.11 drivers [ 2.083709] Registering the dns_resolver key type [ 2.088684] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.096679] ThumbEE CPU extension supported. [ 2.101226] mux: Failed to setup hwmod io irq -22 [ 2.106781] Power Management for AM33XX family [ 2.111694] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 2.118316] Copied the M3 firmware to UMEM [ 2.122650] omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift [ 2.137695] Detected MACID=78:c5:e5:77:ae:c6 [ 2.143768] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 2.153045] Waiting for root device /dev/mmcblk0p2... [ 2.170532] mmc0: new high speed SDHC card at address aaaa [ 2.176940] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 2.183593] mmcblk0: p1 p2 p3 [ 2.474304] kjournald starting. Commit interval 5 seconds [ 2.480102] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended [ 2.491973] EXT3-fs (mmcblk0p2): using internal journal [ 2.497436] EXT3-fs (mmcblk0p2): recovery complete [ 2.504486] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.511749] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.518432] Freeing init memory: 248K INIT: version 2.86 booting Please wait: booting... Starting udev [ 3.038696] udevd (820): /proc/820/oom_adj is deprecated, please use /proc/820/oom_score_adj instead. [ 7.796325] kjournald starting. Commit interval 5 seconds [ 7.802154] EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended [ 7.852722] EXT3-fs (mmcblk0p3): using internal journal [ 7.858215] EXT3-fs (mmcblk0p3): recovery complete [ 7.863250] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode [ 7.988800] alignment: ignoring faults is unsafe on this CPU. Defaulting to fixup mode. Remounting root file system... Caching udev devnodes ALSA: Restoring mixer settings... Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device eth0 No such device ifconfig: SIOCGIFFLAGS: No such device done. Setting up IP spoofing protection: rp_filter. Sat Dec 24 10:11:00 UTC 2011 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Hardware abstraction layer hald Starting Dropbear SSH server: dropbear. Starting telnet daemon. Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. Starting PVR [ 11.649353] pvrsrvkm: disagrees about version of symbol module_layout insmod: error inserting '/lib/modules/3.1.0/kernel/drivers/gpu/pvr/pvrsrvkm.ko': -1 Invalid module format FATAL: Module omaplfb not found. FATAL: Module bufferclass_ti not found. BusyBox v1.13.2 (2011-12-15 15:46:39 CST) multi-call binary Usage: mknod [OPTIONS] NAME TYPE MAJOR MINOR Create a special file (block, character, or pipe) Options: -m Create the special file using the specified mode (default a=rw) TYPEs include: b: Make a block device c or u: Make a character device p: Make a named pipe (MAJOR and MINOR are ignored) chmod: /dev/pvrsrvkm: No such file or directory [ 11.752929] Unhandled fault: external abort on non-linefetch (0x1018) at 0x40262014 Bus error Starting Lighttpd Web Server: lighttpd. 2011-12-24 10:11:01: (log.c.166) server started / / Starting Matrix GUI application. FATAL: Module g_mass_storage not found. *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-dev binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** ,--. ,--.,--. ,--. ,---. ,------. ,--. ,--. | `.' |`--',-' '-.,--. ,--./ O \ | .--. '| `.' | | |'.'| |,--.'-. .-' \ ' /| .-. || '--'.'| |'.'| | | | | || | | | \ ' | | | || |\ \ | | | `--' `--'`--' `--' .-' / `--' `--'`--' '--'`--' `--' `---' ,----. ,----. ,-----.,--. ,--. '.-. |'.-. || .--' \ `.' / .' < .' < '--. `\ .' \ /'-' |/'-' |.--' / / .'. \ `----' `----' `----' '--' '--' Critical Link LLC http://support.criticallink.com mityarm-335x ttyO0 Linux kernel verison Linux armv7l #13 Tue Mar 18 15:13:44 PDT 2014 mityarm-335x login: root root@mityarm-335x:~# ifconfig -a can0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:52 can1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:55 eth1 Link encap:Ethernet HWaddr 78:C5:E5:77:AE:C6 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:40 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:129 errors:0 dropped:0 overruns:0 frame:0 TX packets:129 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:245629 (239.8 KiB) TX bytes:245629 (239.8 KiB) usb0 Link encap:Ethernet HWaddr 1A:3D:56:B7:98:D9 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@mityarm-335x:~# ifconfig eth1 192.168.0.12 [ 42.700012] am335x_lan8820_phy_fixup 7c0ec here addr = 0 [ 42.705871] smsc_phy_config_init [ 42.709442] ..... smsc PHY REGS: 0: VAL: 2000 [ 42.714202] ..... smsc PHY REGS: 1: VAL: 794d [ 42.718933] ..... smsc PHY REGS: 2: VAL: 7 [ 42.723419] ..... smsc PHY REGS: 3: VAL: c0ec [ 42.728179] ..... smsc PHY REGS: 4: VAL: 1e1 [ 42.732788] ..... smsc PHY REGS: 5: VAL: c5e1 [ 42.737548] [ 42.737548] CPSW phy found : id is : 0x7c0ec [ 42.744293] PHY 0:01 not found root@mityarm-335x:~# [ 43.731414] SMSC_config_aneg [ 45.731719] PHY: 0:00 - Link is Up - 100/Full [ 47.731811] PHY: 0:00 - Link is Up - 100/Half root@mityarm-335x:~# ifcongi     config -a can0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:52 can1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:16 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:55 eth1 Link encap:Ethernet HWaddr 78:C5:E5:77:AE:C6 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:40 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:129 errors:0 dropped:0 overruns:0 frame:0 TX packets:129 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:245629 (239.8 KiB) TX bytes:245629 (239.8 KiB) usb0 Link encap:Ethernet HWaddr 1A:3D:56:B7:98:D9 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@mityarm-335x:~# ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1): 56 data bytes  --- 192.168.0.1 ping statistics --- 6 packets transmitted, 0 packets received, 100% packet loss root@mityarm-335x:~# ethtoll  ol eth1 Settings for eth1: Current message level: 0x00000000 (0) Link detected: yes root@mityarm-335x:~#