Project

General

Profile

Activity

From 03/27/2016 to 04/25/2016

04/25/2016

03:42 PM Software Development: RE: All devices on i2c on the AM335 SOM
The factory config definition can be found here:
http://support.criticallink.com/gitweb/?p=linux-mityarm-335x.git;a=...
Jonathan Cormier
03:33 PM Software Development: RE: All devices on i2c on the AM335 SOM
Is there any way I can read the factory config eeprom and use that data to verify the correct SOMs are installed or u... Joseph Orender

04/20/2016

01:48 PM Software Development: RE: High latency for DMTimer interrupt
Mary, Thank you for this detailed post. Please let us know how this works out. Jonathan Cormier
01:44 PM Software Development: RE: High latency for DMTimer interrupt
Here's what I did to apply the RT PREEMPT patch:
Helpful websites:
https://rt.wiki.kernel.org/index.php/RT_PREEMP...
Mary Frantz

04/15/2016

10:06 AM Software Development: RE: High latency for DMTimer interrupt
Note that the RT linux page also has an Ftrace guide: https://rt.wiki.kernel.org/index.php/Ftrace Jonathan Cormier
09:53 AM Software Development: RE: High latency for DMTimer interrupt
Hi Mary,
Regarding RT Linux I would specifically recommend https://rt.wiki.kernel.org/index.php/RT_PREEMPT_HOWTO ...
Gregory Gluszek

04/14/2016

11:43 PM Software Development: RE: High latency for DMTimer interrupt
Mary,
Here is a link to the RT Linux Wiki:
https://rt.wiki.kernel.org/index.php/Main_Page
There's a direct lin...
Bob Duke
03:35 PM Software Development: RE: All devices on i2c on the AM335 SOM
I created a wiki page for this information. Let me know if it answers your question.
[[MitySOM-335x_I2C_Addresses]]
Jonathan Cormier

04/13/2016

02:30 PM Software Development: All devices on i2c on the AM335 SOM
Hello,
I am writing some diagnostic software for our device to run through and make sure everything seems to be pr...
Joseph Orender
11:09 AM Software Development: RE: High latency for DMTimer interrupt
Mary Frantz wrote:
> For more information about how the DM Timer works, refer the the AM335x Technical Reference Man...
Jonathan Cormier
10:59 AM Software Development: RE: High latency for DMTimer interrupt
For more information about how the DM Timer works, refer the the AM335x Technical Reference Manual.
To summarize, ...
Mary Frantz
10:09 AM Software Development: RE: High latency for DMTimer interrupt
Mary Frantz wrote:
> This code:
>
> [...]
>
> prints the value of 'start' (the counter value at the start of t...
Jonathan Cormier
09:48 AM Software Development: RE: High latency for DMTimer interrupt
This code:... Mary Frantz
09:28 AM Software Development: RE: High latency for DMTimer interrupt
Mary Frantz wrote:
> I see this when the printk() call displays the last 16 'start' counter values.
What do you mea...
Jonathan Cormier
08:58 AM Software Development: RE: High latency for DMTimer interrupt
No, this high latency is rare. Typical is more like 3 usec. I see this when the printk() call displays the last 16 ... Mary Frantz

04/12/2016

02:25 PM Software Development: RE: High latency for DMTimer interrupt
Hi Mary,
You mentioned that your maximum latency is ~500 usec. Is this maximum a rare or common occurrence? What ...
Gregory Gluszek
02:02 PM Software Development: High latency for DMTimer interrupt
I have implemented a timer interrupt in a kernel module. At the start of the isr, it reads the timer value which sho... Mary Frantz

04/08/2016

04:24 PM Software Development: RE: Building an SD Card
Tom Tatakis wrote:
> This is a custom board- I did move the init of mmc back to the early init stage as a test and t...
Jonathan Cormier
04:21 PM Software Development: RE: Building an SD Card
Tom,
We are working on a yocto filesystem release which allows you to build a new yocto based filesystem from sour...
Jonathan Cormier
03:52 PM Software Development: RE: Building an SD Card
Actually I do have a question- do you have a pointer to documentation that tells me how to build an SD card image fro... Tom Tatakis
03:50 PM Software Development: RE: Building an SD Card
This is a custom board- I did move the init of mmc back to the early init stage as a test and the file system came up... Tom Tatakis
02:08 PM Software Development: RE: Building an SD Card
Tom, one more question: are you running this on a Critical Link Development Board or your own custom baseboard?
Bob Duke

04/07/2016

09:57 AM Software Development: RE: Building an SD Card
Looking at the logs here are a few things I see.
* On the sd card boots, you are still loading u-boot from the nan...
Jonathan Cormier
09:02 AM Software Development: RE: Building an SD Card
Thanks for the reply- of course now the symptoms have changed. The bad boot now stops waiting for the file system pa... Tom Tatakis

04/06/2016

02:36 PM Software Development: RE: Building an SD Card
Actually 3 logs. The two sd card boot logs and the nand boot log with the new kernel. Jonathan Cormier
02:34 PM Software Development: RE: Building an SD Card
Tom,
Could you include the full boot log of the working and the broken boots?
Jonathan Cormier
12:32 PM Software Development: Building an SD Card
Hello- First, I have a working SD card that boots that I have been using for over a year. I also have a newer kernel... Tom Tatakis
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)