U-Boot SPL 2013.10 (Apr 27 2015 - 11:42:09) MitySOM335x profile 1 - Model No: 3354-HX-X38-RI Serial No: 14008001 Configuring for 512 MB DDR3 @ 400MHz enable_gpmc_cs_config: base = 8000000, size = 0, config1 = 800 Alstom NVSP2 -- NAND Page size = 4096k booting from dev 5 Using 4k bch16 layout ECC Mode = 2 lo = 208/0 nand_spl_load_image: loading 4096 bytes from 100000 to 80800000 nand_spl_load_image: loading 455772 bytes from 100000 to 807fffc0 U-Boot 2013.10 (Apr 27 2015 - 11:42:09) AM335X-GP rev 2 I2C: ready DRAM: 512 MiB WARNING: Caches not enabled enable_gpmc_cs_config: base = 8000000, size = 0, config1 = 800 NAND: Using 4k bch16 layout ECC Mode = 2 lo = 208/0 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 gpio input SPARE0 value = 0 Net: cpsw:1 is connected to cpsw. Reconnecting to cpsw cpsw Hit any key to stop autoboot: 0 SD/MMC found on device 0 reading uenv.txt 2199 bytes read in 5 ms (428.7 KiB/s) Loaded environment from uenv.txt Importing environment from mmc ... Running uenvcmd ... Setting bus to 1 i2c_write: error waiting for addr ACK (status=0x116) Error writing the chip. i2c_write: error waiting for addr ACK (status=0x116) Error writing the chip. reading uImage 3791312 bytes read in 397 ms (9.1 MiB/s) ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0-svn158 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3791248 Bytes = 3.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0-svn158 (mitydsp@mitydsp-dev) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #17 PREEMPT Mon Jan 12 15:28:44 EST 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: mitysom335x [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES2.1 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 510864k/510864k available, 13424k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0787000 (7676 kB) [ 0.000000] .init : 0xc0787000 - 0xc07c4000 ( 244 kB) [ 0.000000] .data : 0xc07c4000 - 0xc085ced0 ( 612 kB) [ 0.000000] .bss : 0xc085cef4 - 0xc08acb80 ( 320 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000152] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 0.038848] pid_max: default: 32768 minimum: 301 [ 0.039001] Security Framework initialized [ 0.039093] Mount-cache hash table entries: 512 [ 0.039489] CPU: Testing write buffer coherency: ok [ 0.040466] devtmpfs: initialized [ 0.060211] omap_hwmod: gfx: failed to hardreset [ 0.075988] omap_hwmod: pruss: failed to hardreset [ 0.077484] print_constraints: dummy: [ 0.077972] NET: Registered protocol family 16 [ 0.080718] OMAP GPIO hardware version 0.1 [ 0.084075] mityarm335x_init... [ 0.084381] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.085723] omap_i2c.3: alias fck already exists [ 0.086029] omap_i2c.2: alias fck already exists [ 0.086853] Registering mcspi 1 [2] [ 0.086914] omap2_mcspi.1: alias fck already exists [ 0.087158] Registering mcspi 2 [2] [ 0.087188] omap2_mcspi.2: alias fck already exists [ 0.087524] edma.0: alias fck already exists [ 0.087554] edma.0: alias fck already exists [ 0.087554] edma.0: alias fck already exists [ 0.091857] baseboard_init [Alstom NVSP2]... [ 0.092163] _omap_mux_get_by_name: Could not find signal gpmc_be1.gpmc_be1 [ 0.093414] omap_hsmmc.0: alias fck already exists [ 0.094116] d_can.1: alias fck already exists [ 0.094818] omap_i2c.1: alias fck already exists [ 0.127593] bio: create slab at 0 [ 0.131225] SCSI subsystem initialized [ 0.133361] usbcore: registered new interface driver usbfs [ 0.133789] usbcore: registered new interface driver hub [ 0.134063] usbcore: registered new device driver usb [ 0.134246] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3 [ 0.134582] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0 [ 0.136108] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.137145] tps65910 3-002d: JTAGREVNUM 0x1 [ 0.142150] print_constraints: VRTC: [ 0.143707] print_constraints: VIO: at 1500 mV [ 0.146087] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal [ 0.148529] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.149597] print_constraints: VDD3: 5000 mV [ 0.151092] print_constraints: VDIG1: at 1800 mV [ 0.152557] print_constraints: VDIG2: at 1800 mV [ 0.154052] print_constraints: VPLL: at 1800 mV [ 0.155517] print_constraints: VDAC: at 1800 mV [ 0.157043] print_constraints: VAUX1: at 1800 mV [ 0.158508] print_constraints: VAUX2: at 3300 mV [ 0.160003] print_constraints: VAUX33: at 3300 mV [ 0.161468] print_constraints: VMMC: at 3300 mV [ 0.162109] tps65910 3-002d: No interrupt support, no core IRQ [ 0.162322] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 0.178039] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.179412] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.180267] Switching to clocksource gp timer [ 0.205108] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.205322] musb-hdrc musb-hdrc.0: dma type: dma-cppi41 [ 0.206298] musb-hdrc musb-hdrc.0: USB OTG mode controller at e081c000 using PIO, IRQ 18 [ 0.206542] musb-hdrc musb-hdrc.1: dma type: dma-cppi41 [ 0.206970] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 0.207061] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 [ 0.207244] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.207244] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.207275] usb usb1: Product: MUSB HDRC host driver [ 0.207275] usb usb1: Manufacturer: Linux 3.2.0-svn158 musb-hcd [ 0.207275] usb usb1: SerialNumber: musb-hdrc.1 [ 0.208312] hub 1-0:1.0: USB hub found [ 0.208374] hub 1-0:1.0: 1 port detected [ 0.209075] musb-hdrc musb-hdrc.1: USB OTG mode controller at e081e800 using PIO, IRQ 19 [ 0.209808] NET: Registered protocol family 2 [ 0.210083] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.210968] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.211242] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.211395] TCP: Hash tables configured (established 16384 bind 16384) [ 0.211425] TCP reno registered [ 0.211425] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.211456] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.211730] NET: Registered protocol family 1 [ 0.212341] RPC: Registered named UNIX socket transport module. [ 0.212341] RPC: Registered udp transport module. [ 0.212371] RPC: Registered tcp transport module. [ 0.212371] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.212677] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.232147] VFS: Disk quotas dquot_6.5.2 [ 0.232269] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.234710] msgmni has been set to 997 [ 0.235931] io scheduler noop registered [ 0.235931] io scheduler deadline registered [ 0.236145] io scheduler cfq registered (default) [ 0.238433] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.241180] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 0.918640] console [ttyO0] enabled [ 0.922943] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 [ 0.931274] zilog_escc_init returning with 0 [ 0.953613] brd: module loaded [ 0.963623] loop: module loaded [ 0.967132] i2c-core: driver [tsl2550] using legacy suspend method [ 0.973724] i2c-core: driver [tsl2550] using legacy resume method [ 0.980133] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write [ 0.992980] MitySOM-335x: Part Number = 3354-HX-X38-RI [ 0.998321] Alstom NVSP2: factory_config_callback [ 1.003814] No SPI NOR Flash found. [ 1.007446] Configuring 512MB NAND device [ 1.012359] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 1.017333] Registering NAND on CS0 [ 1.021057] Enabling CS0, base=0x100000, size=0xf00000, config7=0xf40 [ 1.027740] Registering CS0, resource start=0x100000, end=0xffffff [ 1.037628] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes) [ 1.043457] Creating 1 MTD partitions on "spi_flash": [ 1.048736] 0x000000000000-0x000000800000 : "NOR User Defined" [ 1.057312] omap2-nand driver initializing [ 1.062072] ONFI flash detected [ 1.065460] ONFI param page 0 valid [ 1.069091] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAWP) [ 1.077453] Creating 8 MTD partitions on "omap2-nand.0": [ 1.083007] 0x000000000000-0x000000040000 : "SPL" [ 1.089721] 0x000000040000-0x000000080000 : "SPL.backup1" [ 1.097137] 0x000000080000-0x0000000c0000 : "SPL.backup2" [ 1.104431] 0x0000000c0000-0x000000100000 : "SPL.backup3" [ 1.111846] 0x000000100000-0x000000300000 : "U-Boot" [ 1.119049] 0x000000300000-0x000000340000 : "U-Boot Env" [ 1.126342] 0x000000340000-0x000000840000 : "Kernel" [ 1.134246] 0x000000840000-0x000020000000 : "File System" [ 1.247436] OneNAND driver initializing [ 1.253967] CAN device driver interface [ 1.257965] CAN bus driver for Bosch D_CAN controller 1.0 [ 1.264617] d_can d_can.1: device registered (irq=55, irq_obj=56) [ 1.320922] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 1.327331] davinci_mdio davinci_mdio.0: detected phy mask fffffff9 [ 1.334350] nvsp2_phy_fixup phy_id = 0x221622, addr = 1 [ 1.340484] nvsp2_phy_fixup phy_id = 0x221622, addr = 2 [ 1.346221] davinci_mdio.0: probed [ 1.349761] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver Micrel KSZ9031 Gigabit PHY [ 1.358856] davinci_mdio davinci_mdio.0: phy[2]: device 0:02, driver Micrel KSZ9031 Gigabit PHY [ 1.368438] usbcore: registered new interface driver cdc_ether [ 1.374755] usbcore: registered new interface driver cdc_subset [ 1.381011] Initializing USB Mass Storage driver... [ 1.386322] usbcore: registered new interface driver usb-storage [ 1.392639] USB Mass Storage support registered. [ 1.398132] mousedev: PS/2 mouse device common for all mice [ 1.404663] dev addr = df8c6408 [ 1.407928] pdev addr = df8c6400 [ 1.414184] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0 [ 1.427459] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc0 [ 1.435455] i2c /dev entries driver [ 1.440246] Linux media interface: v0.10 [ 1.444641] Linux video capture interface: v2.00 [ 1.449859] usbcore: registered new interface driver uvcvideo [ 1.455932] USB Video Class driver (1.1.1) [ 1.465301] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.474121] cpuidle: using governor ladder [ 1.479095] cpuidle: using governor menu [ 1.486511] usbcore: registered new interface driver usbhid [ 1.492462] usbhid: USB HID core driver [ 1.497253] usbcore: registered new interface driver snd-usb-audio [ 1.532562] ALSA device list: [ 1.535736] No soundcards found. [ 1.539276] oprofile: hardware counters not available [ 1.544677] oprofile: using timer interrupt. [ 1.549163] nf_conntrack version 0.5.0 (7982 buckets, 31928 max) [ 1.556243] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.561981] TCP cubic registered [ 1.565399] NET: Registered protocol family 17 [ 1.570068] can: controller area network core (rev 20090105 abi 8) [ 1.576751] NET: Registered protocol family 29 [ 1.581512] can: raw protocol (rev 20090105) [ 1.585998] can: broadcast manager protocol (rev 20090105 t) [ 1.592041] lib80211: common routines for IEEE802.11 drivers [ 1.598052] Registering the dns_resolver key type [ 1.603088] Registering FPGA on CS1 [ 1.606811] Enabling CS1, base=0x1000000, size=0x1000000, config7=0xf41 [ 1.613739] Registering CS1, resource start=0x1000000, end=0x1ffffff [ 1.620910] fpga_base_probe constant1 = 0x89ab, constant2 = 0xcdef [ 1.627563] mmc0: new high speed SDHC card at address 59b4 [ 1.736145] mmcblk0: mmc0:59b4 SDC 14.9 GiB [ 1.843322] mmcblk0: p1 p2 p3 [ 1.846710] zilog_escc: ttyZ0 at MMIO 0x1008004 (irq = 256) is a zs (ESCC) [ 1.855957] zilog_escc: ttyZ1 at MMIO 0x1008000 (irq = 256) is a zs (ESCC) [ 1.863952] slot_id_probe [ 1.866729] slot_id_probe - exit [ 1.870422] nvio_probe [ 1.872985] nvio_probe - exit [ 1.876342] i2c_eeprom_probe [ 1.879364] i2c_eeprom_probe - exit [ 1.883361] i2c_mbox_probe [ 1.886199] i2c_mbox_probe - exit [ 1.889953] vsp_probe [ 1.892395] vsp_probe - exit [ 1.895416] Registering ENET on CS2 [ 1.899047] Enabling CS2, base=0x2000000, size=0x1000000, config7=0xf42 [ 1.905975] Registering CS2, resource start=0x2000000, end=0x2ffffff [ 1.912963] ks8851_mll ks8851_mll: (unregistered net_device): message enable is 0 [ 1.920806] ks8851_mll ks8851_mll: (unregistered net_device): the selftest passes [ 1.940338] ks8851_mll ks8851_mll: eth0: Using random mac address [ 1.946807] ks8851_mll ks8851_mll: eth0: Mac address is: 0e:d0:78:51:41:b6 [ 1.954071] ks8851_mll ks8851_mll: eth0: Found chip, family: 0x88, id: 0x7, rev: 0x1 [ 1.962188] ks8851_mll ks8851_mll: eth0: MARM register value: 0x7851 [ 1.968841] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 1.976867] ThumbEE CPU extension supported. [ 1.981414] mux: Failed to setup hwmod io irq -22 [ 1.987823] Power Management for AM33XX family [ 1.992706] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 1.999359] Copied the M3 firmware to UMEM [ 2.003662] omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift [ 2.024047] Detected MACID=90:59:af:91:32:22 [ 2.033233] tps65910-rtc tps65910-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.283813] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended [ 2.293426] kjournald starting. Commit interval 5 seconds [ 2.303192] EXT3-fs (mmcblk0p2): using internal journal [ 2.308654] EXT3-fs (mmcblk0p2): recovery complete [ 2.322814] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.330078] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.336730] Freeing init memory: 244K INIT: version 2.86 booting Please wait: booting... Error opening /dev/fb0: No such device Starting udev [ 2.836120] udevd (805): /proc/805/oom_adj is deprecated, please use /proc/805/oom_score_adj instead. [ 8.080780] EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended [ 8.090423] kjournald starting. Commit interval 5 seconds [ 8.112243] EXT3-fs (mmcblk0p3): using internal journal [ 8.118041] EXT3-fs (mmcblk0p3): recovery complete [ 8.123413] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode [ 93.333190] alignment: ignoring faults is unsafe on this CPU. Defaulting to fixup mode. Remounting root file system... Caching udev devnodes ALSA: Restoring mixer settings... /usr/sbin/alsactl: load_state:1625: No soundcards found... Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCSIFADDR: No such device route: SIOCADDRT: No such device done. Setting up IP spoofing protection: rp_filter. Fri Dec 19 01:36:00 UTC 2014 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Hardware abstraction layer hald Starting Dropbear SSH server: dropbear. Starting telnet daemon. Starting network benchmark server: netserver. Starting syslogd/klogd: done Starting thttpd. Module pvrsrvkm failed to load. Retrying. Running /sbin/depmod Starting Lighttpd Web Server: lighttpd. 2014-12-19 01:36:01: (log.c.166) server started / / Starting Matrix GUI application. FATAL: Module g_mass_storage not found. *************************************************************** *************************************************************** NOTICE: This file system contains the followin GPLv3 packages: binutils-dev binutils-symlinks binutils gdbserver If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If tè ,--. ,--.,--. ,--. ,---. ,-----. ,--. ,--. | `.' |`--',-' '-.,--. ,--.' .-' ' .-. '| `.' | | |'.'| |,--.'-. .-' \ ' / `. `-. | | | || |'.'| | | | | || | | | \ ' .-' |' '-' '| | | | `--' `--'`--' `--' .-' / `-----' `-----' `--' `--' `---' ,----. ,----. ,-----.,--. ,--. '.-. |'.-. || .--' \ `.' / .' < .' < '--. `\ .' \ /'-' |/'-' |.--' / / .'. \ `----' `----' `----' '--' '--' Critical Link LLC http://support.criticallink.com mitysom-335x ttyO0 Linux kernel verison Linux armv7l #17 PREEMPT Mon Jan 12 15:28:44 EST 2015 mitysom-335x login: