U-Boot SPL 2013.10 (Apr 27 2015 - 11:42:09) MitySOM335x profile 1 - Model No: 3354-HX-X38-RI Serial No: 14008001 Configuring for 512 MB DDR3 @ 400MHz enable_gpmc_cs_config: base = 8000000, size = 0, config1 = 800 Alstom NVSP2 -- NAND Page size = 4096k booting from dev 5 Using 4k bch16 layout ECC Mode = 2 lo = 208/0 nand_spl_load_image: loading 4096 bytes from 100000 to 80800000 nand_spl_load_image: loading 455772 bytes from 100000 to 807fffc0 U-Boot 2013.10 (Apr 27 2015 - 11:42:09) AM335X-GP rev 2 I2C: ready DRAM: 512 MiB WARNING: Caches not enabled enable_gpmc_cs_config: base = 8000000, size = 0, config1 = 800 NAND: Using 4k bch16 layout ECC Mode = 2 lo = 208/0 512 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 gpio input SPARE0 value = 0 Net: cpsw:1 is connected to cpsw. Reconnecting to cpsw cpsw Hit any key to stop autoboot: 0 SD/MMC found on device 0 reading uenv.txt 2199 bytes read in 5 ms (428.7 KiB/s) Loaded environment from uenv.txt Importing environment from mmc ... Running uenvcmd ... Setting bus to 1 i2c_write: error waiting for addr ACK (status=0x116) Error writing the chip. i2c_write: error waiting for addr ACK (status=0x116) Error writing the chip. reading uImage 3825680 bytes read in 401 ms (9.1 MiB/s) ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Linux-3.2.0-svn333 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3825616 Bytes = 3.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK XIP Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 3.2.0-svn333 (mitydsp@mitydsp-dev) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #45 PREEMPT Tue Apr 5 16:05:51 EDT 2016 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: mitysom335x [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES2.1 (sgx neon ) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 510888k/510888k available, 13400k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0780000 (7648 kB) [ 0.000000] .init : 0xc0780000 - 0xc07bb000 ( 236 kB) [ 0.000000] .data : 0xc07bc000 - 0xc0854700 ( 610 kB) [ 0.000000] .bss : 0xc0854724 - 0xc08a6418 ( 328 kB) [ 0.000000] NR_IRQS:396 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000122] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) [ 0.089080] pid_max: default: 32768 minimum: 301 [ 0.089233] Security Framework initialized [ 0.089324] Mount-cache hash table entries: 512 [ 0.089721] CPU: Testing write buffer coherency: ok [ 0.090698] devtmpfs: initialized [ 0.110961] omap_hwmod: pruss: failed to hardreset [ 0.112457] print_constraints: dummy: [ 0.112976] NET: Registered protocol family 16 [ 0.115692] OMAP GPIO hardware version 0.1 [ 0.119384] mityarm335x_init... [ 0.119720] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.120544] Configuring I2C Bus 1 [ 0.120635] omap_i2c.2: alias fck already exists [ 0.120910] Configuring I2C Bus 2 [ 0.120971] omap_i2c.3: alias fck already exists [ 0.122039] Registering mcspi 1 [2] [ 0.122070] omap2_mcspi.1: alias fck already exists [ 0.122344] Registering mcspi 2 [2] [ 0.122375] omap2_mcspi.2: alias fck already exists [ 0.122680] edma.0: alias fck already exists [ 0.122711] edma.0: alias fck already exists [ 0.122711] edma.0: alias fck already exists [ 0.128021] omap_i2c.1: alias fck already exists [ 0.161041] bio: create slab at 0 [ 0.164062] SCSI subsystem initialized [ 0.166168] usbcore: registered new interface driver usbfs [ 0.166564] usbcore: registered new interface driver hub [ 0.166839] usbcore: registered new device driver usb [ 0.168304] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz [ 0.179229] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.180297] tps65910 3-002d: JTAGREVNUM 0x1 [ 0.185028] print_constraints: VRTC: [ 0.186553] print_constraints: VIO: at 1500 mV [ 0.188903] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal [ 0.191436] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal [ 0.192504] print_constraints: VDD3: 5000 mV [ 0.193969] print_constraints: VDIG1: at 1800 mV [ 0.195465] print_constraints: VDIG2: at 1800 mV [ 0.196960] print_constraints: VPLL: at 1800 mV [ 0.198425] print_constraints: VDAC: at 1800 mV [ 0.199951] print_constraints: VAUX1: at 1800 mV [ 0.201416] print_constraints: VAUX2: at 3300 mV [ 0.202911] print_constraints: VAUX33: at 3300 mV [ 0.204406] print_constraints: VMMC: at 3300 mV [ 0.205017] tps65910 3-002d: No interrupt support, no core IRQ [ 0.219116] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz [ 0.219787] pps_core: LinuxPPS API ver. 1 registered [ 0.219787] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.219970] PTP clock support registered [ 0.221069] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.221954] Switching to clocksource gp timer [ 0.246734] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 0.247406] NET: Registered protocol family 2 [ 0.247680] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.248199] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.248474] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.248626] TCP: Hash tables configured (established 16384 bind 16384) [ 0.248626] TCP reno registered [ 0.248657] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.248657] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.248962] NET: Registered protocol family 1 [ 0.249542] RPC: Registered named UNIX socket transport module. [ 0.249542] RPC: Registered udp transport module. [ 0.249572] RPC: Registered tcp transport module. [ 0.249572] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.249877] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.253692] audit: initializing netlink socket (disabled) [ 0.253753] type=2000 audit(0.250:1): initialized [ 0.269775] VFS: Disk quotas dquot_6.5.2 [ 0.269866] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.272338] msgmni has been set to 997 [ 0.273925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 0.273956] io scheduler noop registered [ 0.273956] io scheduler deadline registered [ 0.274139] io scheduler cfq registered (default) [ 0.276336] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.278961] zilog_escc_init returning with 0 [ 0.299041] brd: module loaded [ 0.306091] loop: module loaded [ 0.306335] i2c-core: driver [tsl2550] using legacy suspend method [ 0.306365] i2c-core: driver [tsl2550] using legacy resume method [ 0.306457] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write [ 0.312316] MitySOM-335x: Part Number = 3354-HX-X38-RI [ 0.312316] No SPI NOR Flash found. [ 0.312316] Configuring 512MB NAND device [ 0.312530] mityarm335x_nand_init: calling omap_nand_init- 4k [ 0.312530] mityarm335x_nand_init: calling omap_init_gpmc [ 0.313201] omap-gpmc omap-gpmc: GPMC revision 6.0 [ 0.313201] gpmc_probe: calling gpmc_nand_init [ 0.313232] gpmc_probe: nr= 8, cs= 0, name= SPL [ 0.313232] Registering NAND on CS0 [ 0.313232] Enabling CS0, base=0x100000, size=0xf00000, config7=0xf40 [ 0.313262] Registering CS0, resource start=0x100000, end=0xffffff [ 0.313323] gpmc_nand_init: registering paltform device gpmc_nand_device= omap2-nand [ 0.317413] omap2-nand driver initializing [ 0.317504] omap_nand_probe: pdev->name= omap2-nand [ 0.317779] ONFI flash detected [ 0.317901] ONFI param page 0 valid [ 0.317932] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAWP) [ 0.317932] nand_scan_tail: ENTERED (0xdf172010) [ 0.317962] omap_nand_probe: calling mtd_device_parse_register [ 0.317993] add_mtd_partitions: Creating 8 MTD partitions on "omap2-nand.0" (mtd=0xdf172010): [ 0.317993] allocate_partition: 0x000000000000-0x000000040000 : "SPL" [ 0.318084] add_mtd_device: mtd= 0xdf218800, assigning index= 0 [ 0.319976] allocate_partition: 0x000000040000-0x000000080000 : "SPL.backup1" [ 0.320037] add_mtd_device: mtd= 0xdf23bc00, assigning index= 1 [ 0.321746] allocate_partition: 0x000000080000-0x0000000c0000 : "SPL.backup2" [ 0.321807] add_mtd_device: mtd= 0xdf23b000, assigning index= 2 [ 0.323822] allocate_partition: 0x0000000c0000-0x000000100000 : "SPL.backup3" [ 0.323913] add_mtd_device: mtd= 0xdf1e9400, assigning index= 3 [ 0.325561] allocate_partition: 0x000000100000-0x000000300000 : "U-Boot" [ 0.326019] add_mtd_device: mtd= 0xdf1ee800, assigning index= 4 [ 0.327697] allocate_partition: 0x000000300000-0x000000340000 : "U-Boot Env" [ 0.327758] add_mtd_device: mtd= 0xdf249c00, assigning index= 5 [ 0.329376] allocate_partition: 0x000000340000-0x000000840000 : "Kernel" [ 0.330474] add_mtd_device: mtd= 0xdf249000, assigning index= 6 [ 0.332336] allocate_partition: 0x000000840000-0x000020000000 : "File System" [ 0.438659] add_mtd_device: mtd= 0xdf24f400, assigning index= 7 [ 0.440551] OneNAND driver initializing [ 0.443389] CAN device driver interface [ 0.443420] CAN bus driver for Bosch D_CAN controller 1.0 [ 0.492187] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6 [ 0.492218] davinci_mdio davinci_mdio.0: detected phy mask fffffff9 [ 0.492706] nvsp2_phy_fixup phy_id = 0x221622, addr = 1 [ 0.493469] nvsp2_phy_fixup phy_id = 0x221622, addr = 2 [ 0.493713] davinci_mdio.0: probed [ 0.493743] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver Micrel KSZ9031 Gigabit PHY [ 0.493743] davinci_mdio davinci_mdio.0: phy[2]: device 0:02, driver Micrel KSZ9031 Gigabit PHY [ 0.494201] usbcore: registered new interface driver cdc_ether [ 0.494415] usbcore: registered new interface driver cdc_subset [ 0.494476] Initializing USB Mass Storage driver... [ 0.494689] usbcore: registered new interface driver usb-storage [ 0.494720] USB Mass Storage support registered. [ 0.495452] mousedev: PS/2 mouse device common for all mice [ 0.498474] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0 [ 0.504547] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc0 [ 0.504760] i2c /dev entries driver [ 0.505950] Linux media interface: v0.10 [ 0.506164] Linux video capture interface: v2.00 [ 0.510711] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 0.515991] cpuidle: using governor ladder [ 0.516845] cpuidle: using governor menu [ 0.518768] usbcore: registered new interface driver usbhid [ 0.518798] usbhid: USB HID core driver [ 0.520080] usbcore: registered new interface driver snd-usb-audio [ 0.547668] ALSA device list: [ 0.547668] No soundcards found. [ 0.547698] oprofile: hardware counters not available [ 0.547698] oprofile: using timer interrupt. [ 0.547760] nf_conntrack version 0.5.0 (7982 buckets, 31928 max) [ 0.548614] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.548797] TCP cubic registered [ 0.548797] NET: Registered protocol family 17 [ 0.548828] can: controller area network core (rev 20090105 abi 8) [ 0.549072] NET: Registered protocol family 29 [ 0.549072] can: raw protocol (rev 20090105) [ 0.549102] can: broadcast manager protocol (rev 20090105 t) [ 0.549194] 8021q: 802.1Q VLAN Support v1.8 [ 0.549224] lib80211: common routines for IEEE802.11 drivers [ 0.549285] Registering the dns_resolver key type [ 0.549407] Registering FPGA on CS1 [ 0.549407] Enabling CS1, base=0x1000000, size=0x1000000, config7=0xf41 [ 0.549438] Registering CS1, resource start=0x1000000, end=0x1ffffff [ 0.550048] baseboard_init_late [Alstom NVSP2]... [ 0.550292] omap_hsmmc.0: alias fck already exists [ 0.551574] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 [ 1.659545] console [ttyO0] enabled [ 1.664947] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 [ 1.673736] baseboard_setup_spi1_devices: calling spi_register_board_info() [ 1.681701] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes) [ 1.687377] add_mtd_partitions: Creating 1 MTD partitions on "spi_flash" (mtd=0xdf2ad410): [ 1.696014] allocate_partition: 0x000000000000-0x000000800000 : "NOR User Defined" [ 1.703948] add_mtd_device: mtd= 0xdf2ad000, assigning index= 8 [ 1.917053] zilog_escc: ttyZ0 at MMIO 0x1008004 (irq = 256) is a zs (ESCC) [ 1.924835] zilog_escc: ttyZ1 at MMIO 0x1008000 (irq = 256) is a zs (ESCC) [ 1.936248] d_can.1: alias fck already exists [ 1.942382] d_can d_can.1: device registered (irq=55, irq_obj=56) [ 1.951660] tiadc tiadc: attached adc driver [ 1.956390] Registering ENET on CS2 [ 1.960052] Enabling CS2, base=0x2000000, size=0x1000000, config7=0xf42 [ 1.966979] Registering CS2, resource start=0x2000000, end=0x2ffffff [ 1.974151] ks8851_mll ks8851_mll: (unregistered net_device): message enable is 0 [ 1.981964] ks8851_mll ks8851_mll: (unregistered net_device): the selftest passes [ 2.001708] ks8851_mll ks8851_mll: eth0: Using random mac address [ 2.008178] ks8851_mll ks8851_mll: eth0: Mac address is: 16:36:93:4b:7f:92 [ 2.015380] ks8851_mll ks8851_mll: eth0: Found chip, family: 0x88, id: 0x7, rev: 0x1 [ 2.023468] ks8851_mll ks8851_mll: eth0: MARM register value: 0x934b [ 2.030120] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.038146] ThumbEE CPU extension supported. [ 2.042694] mux: Failed to setup hwmod io irq -22 [ 2.049591] Power Management for AM33XX family [ 2.054260] pm: Err (-22) setting core voltage setting [ 2.059844] Trying to load am335x-pm-firmware.bin (60 secs timeout) [ 2.066528] Copied the M3 firmware to UMEM [ 2.070861] Unable to read CM3 firmware version [ 2.089935] Detected MACID=90:59:af:91:32:22 [ 2.095947] cpsw: Detected MACID = 90:59:af:91:32:24 [ 2.105895] tps65910-rtc tps65910-rtc: setting system clock to 2014-12-19 01:38:38 UTC (1418953118) [ 2.116363] Waiting for root device /dev/mmcblk0p2...