-Boot 2009.11 (Mar 31 2011 - 19:39:18) I2C : ready DRAM: 128 MB NAND: 256 MiB MMC: davinci : 0 In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz EMIFA CLock : 100000000 Hz DSP Clock : 300000000 Hz ANSYNC3 Clock : 150000000 Hz Enet config : 2 MMC 0 Enable : 0 Resetting ethernet phy Net: Ethernet PHY: GENERIC @ 0x30 [0x8] Hit any key to stop autoboot: 0 8192 KiB M25p64 at 0:0 is now current device ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-2.6.34-rc1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2203396 Bytes = 2.1 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. ... ... spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 m25p80 spi1.0: m25p64 (8192 Kbytes) Creating 8 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "ubl" 0x000000010000-0x000000090000 : "u-boot" 0x000000090000-0x0000000a0000 : "u-boot-env" 0x0000000a0000-0x0000000b0000 : "periph-config" 0x0000000b0000-0x000000100000 : "reserved" 0x000000100000-0x000000400000 : "kernel" 0x000000400000-0x000000600000 : "fpga" 0x000000600000-0x000000800000 : "spare" spi_davinci spi_davinci.1: Controller at 0xfef0e000 CAN device driver interface mcp251x spi1.1: probed console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open Host Controller (OHCI) Driver ohci ohci.0 Da8xx OHCI ohci ohci.0 new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohc.0: irq 59, io mem 0x01e25000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc omap_rtc: RTC power up reset detected omap_rtc omap_rtc: already running i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver No device for DAI AK4535 Cirrus Logic CS4270 ALSA SoC Codec Driver No device codec for codec dsd1791 No device codec for codec DAI dsd1791 No device codec for codec DAI PCM3008 HiFi No device codec for codec DAI SSM2602 No device codec for codec DAI tlv320aic23 No device codec for codec DAI UDA134x No device codec for codec DAI WM8510 HiFi ata1: SATA link down (SStatus 0 SControl 300) No device for DAI WM8728 No device for DAI WM8750 No device for DAI WM8971 No device for DAI WM8990 ADC/DAC Primary asoc: dsd1791 <-> davinci-i2s mapping ok soc-audio soc-audio.0: DSD1791 Audio Codec ALSA device list: #0: MityDSP-L138 INDIO (dsd1791) TCP cubic registered NET: Registered protocol family 17 Can: Controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) Clocks: disable unused i2c1 Clocks: disable unused emac Clocks: disable unused lcdc Clocks: disable unused spi0 Clocks: disable unused mcbsp0 Clocks: disable unused mcbsp1 Clocks: disable unused vpif Clocks: disable unused ecap Clocks: disable unused ehrpwm regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on regulator_init_complete: incomplete constraints, leaving VDCDC3 on regulator_init_complete: incomplete constraints, leaving VDCDC2 on regulator_init_complete: incomplete constraints, leaving VDCDC1 on emac-mii: probed omap_rtc omap_rtc: setting system clock to 2011-05-18 00:38:57 UTC (1305679137) Empty flash at 0x045cfe40 ends at 0x045d0000 jffs2_scan_inode_node(): CRC failed on node at 0x05f0a7f0: Read 0xffffffff, calculated 0x4d5b2912 Empty flash at 0x05f0a84c ends at 0x05f0b000 Empty flash at 0x05f1682c ends at 0x05f17000 Empty flash at 0x0670a958 ends at 0x0670b000 VFS: Mounted root (jffs2 filesystem) on device 31:0. Feeing init memory: 140K INIT: Version 2.86 booting Please wait: booting... Starting udev Remounting root file system... Caching udev devnodes Populating dev cache NET: Registered protocol family 10 Configuring network interfaces... eth0 attached PHY driver [Generic PHY] (mii_b us:phy_addr=1:03, id=40005201) ADDRCONF (NETDEV_UP): eth0: link is not ready udhcpc (v1.13.2) started run-parts: /etc/udhcp.d/00avahi-autoipd exited with code 1 Sending discover... PHY: 1:03 - Link is up - 100/Full ADDRCONF (NETDEV_CHANGE): eth0: link becomes ready Sending discover... Sending discover... Starting portmap daemon: portmap. portmap: fork: No such devicenet.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). svc: failed to register nfsdv2 RPC service (error 111). nfsd: last server has exited, flushing export cache JFFS2 notice: (1201) check_node_data: wrong data CRC in data node at 0x0670a6a0: read 0x14dd865d, calculated 0x13d965b8