U-Boot SPL 2013.01.01 (Apr 04 2019 - 10:37:13) BOARD : Critical Link MitySOM-5CSx Module CLOCK: EOSC1 clock 25000 KHz CLOCK: EOSC2 clock 25000 KHz CLOCK: F2S_SDR_REF clock 0 KHz CLOCK: F2S_PER_REF clock 0 KHz CLOCK: MPU clock 800 MHz CLOCK: DDR clock 400 MHz CLOCK: UART clock 100000 KHz CLOCK: MMC clock 50000 KHz CLOCK: QSPI clock 400000 KHz RESET: COLD INFO : Watchdog enabled SDRAM: Initializing MMR registers SDRAM: Calibrating PHY SEQ.C: Preparing to start memory calibration SEQ.C: CALIBRATION PASSED SDRAM: 1024 MiB SDRAM: Initializing SDRAM ECC SDRAM: ECC initialized successfully with 1547 ms SDRAM: ECC Enabled ALTERA DWMMC: 0 U-Boot 2013.01.01 (Apr 04 2019 - 10:37:31) Critical Link MitySOM-5CSx CPU : Altera SOCFPGA Platform BOARD : Critical Link MitySOM-5CSx Module I2C: ready DRAM: 1 GiB MMC: ALTERA DWMMC: 0 In: serial Out: serial Err: serial Net: mii0 gpio: pin 28 (bank/mask = 0/0x10000000) gpio: pin 28 (gpio 28) value is 0 gpio: pin 28 (bank/mask = 0/0x10000000) gpio: pin 28 (gpio 28) value is 1 gpio: pin 0 (bank/mask = 0/0x00000001) gpio: pin 0 (gpio 0) value is 1 gpio: pin 9 (bank/mask = 0/0x00000200) gpio: pin 9 (gpio 9) value is 0 gpio: pin 9 (bank/mask = 0/0x00000200) gpio: pin 9 (gpio 9) value is 1 Hit any key to stop autoboot: 0 4433232 bytes read in 237 ms (17.8 MiB/s) 33363 bytes read in 48 ms (678.7 KiB/s) 7007204 bytes read in 352 ms (19 MiB/s) ## Starting application at 0x3FF77598 ... ## Application terminated, rc = 0x0 ## Starting application at 0x3FF77598 ... ## Application terminated, rc = 0x0 ## Flattened Device Tree blob at 00000100 Booting using the fdt blob at 0x00000100 reserving fdt memory region: addr=0 size=1000 Loading Device Tree to 03ff4000, end 03fff252 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.76-rt61-ltsi-07020-g8b1e2f3 (xyz@localhost.localdomain) (gcc version 4.8.3 20 140401 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.04 - Linaro GCC 4.8-2014.04) ) #4 SMP PREEMPT RT Wed Jun 26 11:51:56 CEST 2019 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Terasic SoCkit [ 0.000000] cma: Reserved 16 MiB at 0x2f000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 14 pages/cpu @ee9b9000 s28480 r8192 d20672 u57344 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 195072 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait mem=768M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 751320K/786432K available (7168K kernel code, 484K rwdata, 1448K rodata, 1024K init, 21 8K bss, 18728K reserved, 16384K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b790f4 ( 485 kB) [ 0.000000] .bss : 0xc0b790f4 - 0xc0bafcd0 ( 219 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU kthread priority: 1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x02460000 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB [ 0.000000] L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001 [ 0.000000] GIC: PPI13 is secure or misconfigured [ 0.000000] GIC: PPI13 is secure or misconfigured [ 0.000000] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns [ 0.000006] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns [ 0.000013] Switching to timer-based delay loop, resolution 10ns [ 0.000386] Console: colour dummy device 80x30 [ 0.000529] Calibrating delay loop (skipped), value calculated using timer frequency.. 200.00 BogoMIPS (lpj =1000000) [ 0.000534] pid_max: default: 32768 minimum: 301 [ 0.000643] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000651] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001395] CPU: Testing write buffer coherency: ok [ 0.001401] ftrace: allocating 23117 entries in 68 pages [ 0.048075] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.048309] Setting up static identity map for 0x100000 - 0x100058 [ 0.280097] GIC: PPI13 is secure or misconfigured [ 0.280109] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.280271] Brought up 2 CPUs [ 0.280295] SMP: Total of 2 processors activated (400.00 BogoMIPS). [ 0.280302] CPU: All CPU(s) started in SVC mode. [ 0.281178] devtmpfs: initialized [ 0.292580] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.293090] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 n s [ 0.293117] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.295470] NET: Registered protocol family 16 [ 0.298273] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.314233] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.314251] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.348439] vgaarb: loaded [ 0.349020] SCSI subsystem initialized [ 0.349867] usbcore: registered new interface driver usbfs [ 0.350033] usbcore: registered new interface driver hub [ 0.350206] usbcore: registered new device driver usb [ 0.350383] soc:usbphy@0 supply vcc not found, using dummy regulator [ 0.353457] pps_core: LinuxPPS API ver. 1 registered [ 0.353472] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.353566] PTP clock support registered [ 0.354186] FPGA manager framework [ 0.354716] fpga-region soc:base-fpga-region: FPGA Region probed [ 0.356181] clocksource: Switched to clocksource timer1 [ 0.414380] NET: Registered protocol family 2 [ 0.415091] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.415201] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) [ 0.415701] TCP: Hash tables configured (established 8192 bind 8192) [ 0.415805] UDP hash table entries: 512 (order: 3, 32768 bytes) [ 0.415892] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) [ 0.416362] NET: Registered protocol family 1 [ 0.426888] RPC: Registered named UNIX socket transport module. [ 0.426903] RPC: Registered udp transport module. [ 0.426912] RPC: Registered tcp transport module. [ 0.426920] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.430183] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.446384] NFS: Registering the id_resolver key type [ 0.446421] Key type id_resolver registered [ 0.446431] Key type id_legacy registered [ 0.446452] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.448000] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.448550] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.450417] io scheduler noop registered (default) [ 0.458844] dma-pl330 ffe01000.pdma: Loaded driver for PL330 DMAC-341330 [ 0.458865] dma-pl330 ffe01000.pdma: DBUFF-512x8bytes Num_Chans-8 Num_Peri-32 Num_Events-8 [ 0.466574] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.468530] console [ttyS0] disabled [ 0.468597] ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 37, base_baud = 6250000) is a 16550A [ 1.068107] console [ttyS0] enabled [ 1.072579] ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 38, base_baud = 6250000) is a 16550A [ 1.084290] brd: module loaded [ 1.089245] at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write [ 1.099860] libphy: Fixed MDIO Bus: probed [ 1.106845] CAN device driver interface [ 1.111393] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 1.116429] Ring mode enabled [ 1.119474] DMA HW capability register supported[ 1.123986] Enhanced/Alternate descriptors [ 1.128155] Enabled extended descriptors [ 1.132149] RX Checksum Offload Engine supported [ 1.136836] COE Type 2 [ 1.139274] TX Checksum insertion supported [ 1.143526] Enable RX Mitigation via HW Watchdog Timer [ 1.154541] libphy: stmmac: probed [ 1.157943] eth%d: PHY ID 00221622 at 3 IRQ POLL (stmmac-0:03) active [ 1.166006] ffb40000.usb supply vusb_d not found, using dummy regulator [ 1.172693] ffb40000.usb supply vusb_a not found, using dummy regulator [ 1.179648] dwc2 ffb40000.usb: EPs: 16, dedicated fifos, 8064 entries in SPRAM [ 1.187508] dwc2 ffb40000.usb: DWC OTG Controller [ 1.192227] dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1 [ 1.199386] dwc2 ffb40000.usb: irq 39, io mem 0x00000000 [ 1.205876] hub 1-0:1.0: USB hub found [ 1.209667] hub 1-0:1.0: 1 port detected [ 1.214730] usbcore: registered new interface driver usb-storage [ 1.224391] mousedev: PS/2 mouse device common for all mice [ 1.230624] i2c /dev entries driver [ 1.236730] Synopsys Designware Multimedia Card Interface Driver [ 1.243110] dw_mmc ff704000.dwmmc0: IDMAC supports 32-bit address mode. [ 1.249814] dw_mmc ff704000.dwmmc0: Using internal DMA controller. [ 1.255980] dw_mmc ff704000.dwmmc0: Version ID is 240a [ 1.261258] dw_mmc ff704000.dwmmc0: DW MMC controller at irq 31,32 bit host data width,1024 deep fifo [ 1.296244] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 1.326357] dw_mmc ff704000.dwmmc0: 1 slots initialized [ 1.333486] usbcore: registered new interface driver usbhid [ 1.341052] usbhid: USB HID core driver [ 1.345399] fpga_manager fpga0: Altera SOCFPGA FPGA Manager registered [ 1.352834] altera_hps2fpga_bridge ff400000.fpga_bridge: fpga bridge [lwhps2fpga] registered [ 1.364679] altera_hps2fpga_bridge ff500000.fpga_bridge: fpga bridge [hps2fpga] registered [ 1.374904] NET: Registered protocol family 10 [ 1.380753] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.387673] NET: Registered protocol family 17 [ 1.392133] NET: Registered protocol family 15 [ 1.396565] can: controller area network core (rev 20120528 abi 9) [ 1.402832] NET: Registered protocol family 29 [ 1.407265] can: raw protocol (rev 20120528) [ 1.411522] can: broadcast manager protocol (rev 20161123 t) [ 1.417170] can: netlink gateway (rev 20130117) max_hops=1 [ 1.423015] 8021q: 802.1Q VLAN Support v1.8 [ 1.427252] Key type dns_resolver registered [ 1.431603] ThumbEE CPU extension supported. [ 1.435870] Registering SWP/SWPB emulation handler [ 1.445502] hctosys: unable to open rtc device (rtc0) [ 1.450548] of_cfs_init [ 1.453094] of_cfs_init: OK [ 1.456789] ttyS0 - failed to request DMA [ 1.461026] Waiting for root device /dev/mmcblk0p2... [ 1.478970] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 1.488772] mmc0: new high speed SDHC card at address aaaa [ 1.494922] mmcblk0: mmc0:aaaa SC16G 14.8 GiB [ 1.504426] mmcblk0: p1 p2 p3 [ 1.579833] EXT4-fs (mmcblk0p2): mounting ext3 file system using the ext4 subsystem [ 1.601713] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 1.609824] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 1.626531] devtmpfs: mounted [ 1.630876] Freeing unused kernel memory: 1024K [ 1.734273] random: fast init done INIT: version 2.88 booting Starting udev [ 2.285847] udevd[774]: starting version 3.2.2 [ 2.342156] udevd[775]: starting eudev-3.2.2 [ 2.777989] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) hwclock: can't open '/dev/misc/rtc': No such file or directory Fri May 17 09:55:50 UTC 2019 hwclock: can't open '/dev/misc/rtc': No such file or directory INIT: Entering runlevel: 5 Configuring network interfaces... [ 3.790616] socfpga-dwmac ff702000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 3.799475] socfpga-dwmac ff702000.ethernet eth0: registered PTP clock [ 3.806830] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready done. Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd done. Starting rpcbind daemon...done. starting statd: done Starting atd: OK hwclock: can't open '/dev/misc/rtc': No such file or directory exportfs: can't open /etc/exports for reading starting 8 nfsd kernel threads: [ 4.664432] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 4.676272] NFSD: starting 90-second grace period (net c0b66bc0) done starting mountd: done loading RTC calibration values from /etc/abrtc.cal ... Starting system log daemon...0 Starting kernel log daemon...0 Starting crond: OK Starting Network Interface Plugging Daemon: eth0. Starting tcf-agent: OK Poky (Yocto Project Reference Distro) 2.4.4 mitysom-c5 /dev/ttyS0 mitysom-c5 login: [ 11.056892] socfpga-dwmac ff702000.ethernet eth0: Link is Up - 100Mbps/Full - flow contro l rx/tx [ 11.066905] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 99.882775] random: crng init done Poky (Yocto Project Reference Distro) 2.4.4 mitysom-c5 /dev/ttyS0 mitysom-c5 login: