=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.01.10 07:51:27 =~=~=~=~=~=~=~=~=~=~=~=
dmesg
Linux version 3.2.0+ (vdr@vdr-OptiPlex-780) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #16 PREEMPT Fri Jan 4 10:30:00 CET 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: MityDSP-L138/MityARM-1808
Ignoring unrecognised tag 0x42000101
Memory policy: ECC disabled, Data cache writethrough
DaVinci da850/omap-l138/am18x variant 0x1
On node 0 totalpages: 24576
free_area_init_node: node 0, pgdat c043e108, node_mem_map c046b000
  DMA zone: 192 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 24384 pages, LIFO batch:3
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 24384
Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/mmcblk0p1 rw,rootwait ip=dhcp
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 96MB = 96MB total
Memory: 92872k/92872k available, 5432k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc6800000 - 0xfea00000   ( 898 MB)
    lowmem  : 0xc0000000 - 0xc6000000   (  96 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc03e5d6c   (3960 kB)
      .init : 0xc03e6000 - 0xc040f000   ( 164 kB)
      .data : 0xc0410000 - 0xc043ea80   ( 187 kB)
       .bss : 0xc043eaa4 - 0xc046a4cc   ( 175 kB)
NR_IRQS:245
Console: colour dummy device 80x30
Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
DaVinci: 144 gpio irqs
print_constraints: dummy: 
NET: Registered protocol family 16
baseboard_pre_init: Entered
mityomapl138_setup_nand: using 16 bit data
baseboard_init [IndustrialIO]...
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV 
print_constraints: VDCDC2: 1800 mV 
print_constraints: VDCDC3: 1200 mV 
print_constraints: LDO1: 1800 mV 
print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV 
Switching to clocksource timer0_1
musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
Waiting for USB PHY clock good...
musb-hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn)
musb-hdrc: MHDRC RTL version 1.800 
musb-hdrc: setup fifo_mode 2
musb-hdrc: 7/9 max ep, 2624/4096 memory
musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using PIO, IRQ 58
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
msgmni has been set to 181
io scheduler noop registered (default)
start plist test
end plist test
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A
serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A
console [ttyS1] enabled
serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A
brd: module loaded
loop: module loaded
at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
MityOMAPL138: Found MAC = 00:50:c2:bf:8b:d2
MityOMAPL138: Part Number = 1808-FX-225-RC
ahci ahci: forcing PORTS_IMPL to 0x1
ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc 
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB 3,3V 16-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
Creating 2 MTD partitions on "davinci_nand.1":
0x000000000000-0x000008000000 : "rootfs"
0x000008000000-0x000010000000 : "homefs"
davinci_nand davinci_nand.1: controller rev. 2.5
spi_davinci spi_davinci.1: DMA: supported
spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
spi_davinci spi_davinci.1: registered master spi1
spi spi1.0: setup mode 0, 8 bits/w, 30000000 Hz max --> 0
m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes)
Creating 8 MTD partitions on "m25p80":
0x000000000000-0x000000010000 : "ubl"
0x000000010000-0x000000090000 : "u-boot"
0x000000090000-0x0000000a0000 : "u-boot-env"
0x0000000a0000-0x0000000b0000 : "periph-config"
No LCD configured
MII PHY configured
0x0000000b0000-0x000000100000 : "reserved"
0x000000100000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "fpga"
0x000000600000-0x000000800000 : "spare"
spi_davinci spi_davinci.1: registered child spi1.0
spi spi1.1: setup mode 0, 8 bits/w, 10000000 Hz max --> 0
spi_davinci spi_davinci.1: registered child spi1.1
spi spi1.2: setup mode 0, 8 bits/w, 1000000 Hz max --> 0
spi_davinci spi_davinci.1: registered child spi1.2
spi_davinci spi_davinci.1: Controller at 0xfef0e000
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
CAN device driver interface
mcp251x spi1.1: setup mode 0, 8 bits/w, 10000000 Hz max --> 0
mcp251x spi1.1: probed
davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
davinci_mdio davinci_mdio.0: detected phy mask fffffff7
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci ohci.0: DA8xx OHCI
ohci ohci.0: new USB bus registered, assigned bus number 1
Waiting for USB PHY clock good...
ohci ohci.0: irq 59, io mem 0x01e25000
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: Corsair Accelerator SSD, 5.02, max UDMA/133
ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 1-0:1.0: USB hub found
ata1.00: configured for UDMA/133
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
scsi 0:0:0:0: Direct-Access     ATA      Corsair Accelera 5.02 PQ: 0 ANSI: 5
USB Mass Storage support registered.
 gadget: using random self ethernet address
 gadget: using random host ethernet address
sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
usb0: MAC 0a:c2:6e:49:f4:07
usb0: HOST MAC 56:c3:88:50:4b:9f
 gadget: Ethernet Gadget, version: Memorial Day 2008
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 gadget: g_ether ready
musb-hdrc musb-hdrc: MUSB HDRC host driver
musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
omap_rtc: RTC power up reset detected
omap_rtc: already running
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
regulator_init_complete: LDO2: incomplete constraints, leaving on
regulator_init_complete: LDO1: incomplete constraints, leaving on
regulator_init_complete: VDCDC3: incomplete constraints, leaving on
regulator_init_complete: VDCDC2: incomplete constraints, leaving on
regulator_init_complete: VDCDC1: incomplete constraints, leaving on
console [netcon0] enabled
netconsole: network logging started
mmc0: new high speed SDHC card at address 1234
omap_rtc omap_rtc: setting system clock to 2013-01-06 07:34:25 UTC (1357457665)
ADDRCONF(NETDEV_UP): usb0: link is not ready
mmcblk0: mmc0:1234 SA04G 3.63 GiB 
 mmcblk0: p1 p2
davinci_mdio davinci_mdio.0: resetting idled controller
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201)
ADDRCONF(NETDEV_UP): eth0: link is not ready
PHY: 0:03 - Link is Up - 100/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 172.17.3.137
IP-Config: Complete:
     device=eth0, addr=172.17.3.137, mask=255.255.255.0, gw=172.17.3.1,
     host=172.17.3.137, domain=Jotron.local, nis-domain=(none),
     bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p1): using internal journal
EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:1.
devtmpfs: mounted
Freeing init memory: 164K
udev[1023]: starting version 164
EXT3-fs (sda): error: can't find ext3 filesystem on dev sda.
EXT2-fs (sda): error: can't find an ext2 filesystem on dev sda.
FAT-fs (sda): bogus number of reserved sectors
FAT-fs (sda): Can't find a valid FAT filesystem
VFS: Can't find a Minix filesystem V1 | V2 | V3 on device sda.
cramfs: wrong magic
FAT-fs (sda): bogus number of reserved sectors
FAT-fs (sda): Can't find a valid FAT filesystem
eth0: no IPv6 routers present
EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda1): using internal journal
EXT3-fs (sda1): mounted filesystem with writeback data mode
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
svc: failed to register lockdv1 RPC service (errno 97).
root@am180x-evm:~#