OMAP-L138/AM-1808/AM-1810 initialization passed! Configuring 128MB mDDR Booting TI User Boot Loader UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53 UBL Flashtype: SPI Starting SPI Memory Copy... Valid magicnum, 0x55424CBB, found at offset 0x00010000. DONE Jumping to entry point at 0xC1080000. U-Boot 2009.11-00023-gfca022b96949 (Jun 29 2022 - 17:21:16) I2C: ready DRAM: 128 MB NAND: 256 MiB MMC: davinci: 0 In: serial Out: serial Err: serial Info - Didn't find block MityDSP-L138 - Model No: L138-DG-225-RI Serial No: 122098 Part Number: ARM Clock : 300000000 Hz DDR Clock : 150000000 Hz EMIFA CLock : 100000000 Hz DSP Clock : 300000000 Hz ASYNC3 Clock : 150000000 Hz Enet config : 2 MMC 0 Enable : 1 Resetting ethernet phy Net: Ethernet PHY: GENERIC @ 0x03 [0x8] Hit any key to stop autoboot: 3  2  1  0 Device: davinci Manufacturer ID: 3 OEM: 5344 Name: SA08G Tran Speed: 25000000 Rd Block Len: 512 SD version 2.0 High Capacity: Yes Capacity: 7948206080 Bus Width: 4-bit Loading file "/boot/uImage" from mmc device 0:1 (xxa1) 2530232 bytes read ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-3.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2530168 Bytes = 2.4 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 3.2.0 (root@mitydsp) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #1 PREEMPT Mon Jan 13 11:06:16 EST 2014 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: MityDSP-L138/MityARM-1808 Ignoring unrecognised tag 0x42000101 Memory policy: ECC disabled, Data cache writethrough DaVinci da850/omap-l138/am18x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/mmcblk0p1 rw rootwait ip=none PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 91368k/91368k available, 6936k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc6800000 - 0xfea00000 ( 898 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc052c598 (5266 kB) .init : 0xc052d000 - 0xc0555000 ( 160 kB) .data : 0xc0556000 - 0xc05b5a80 ( 383 kB) .bss : 0xc05b5aa4 - 0xc05e2490 ( 179 kB) NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 148.88 BogoMIPS (lpj=744448) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok devtmpfs: initialized DaVinci: 144 gpio irqs print_constraints: dummy: NET: Registered protocol family 16 baseboard_pre_init: Entered mityomapl138_setup_nand: using 8 bit data baseboard_init [IndustrialIO]... bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV print_constraints: VDCDC2: 1800 mV print_constraints: VDCDC3: 1200 mV print_constraints: LDO1: 1800 mV print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV Advanced Linux Sound Architecture Driver Version 1.0.24. Switching to clocksource timer0_1 musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) Waiting for USB PHY clock good... musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using PIO, IRQ 58 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 178 io scheduler noop registered (default) start plist test end plist test Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write MityOMAPL138: Found MAC = 00:50:c2:e6:7b:7a MityOMAPL138: Part Number = L138-DG-225-RI ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67 ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP) Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 Creating 2 MTD partitions on "davinci_nand.1": 0x000000000000-0x000008000000 : "rootfs" 0x000008000000-0x000010000000 : "homefs" davinci_nand davinci_nand.1: controller rev. 2.5 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes) Creating 8 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "ubl" 0x000000010000-0x000000090000 : "u-boot" 0x000000090000-0x0000000a0000 : "u-boot-env" 0x0000000a0000-0x0000000b0000 : "periph-config" No LCD configured MII PHY configured 0x0000000b0000-0x000000100000 : "reserved" 0x000000100000-0x000000400000 : "kernel" 0x000000400000-0x000000600000 : "fpga" 0x000000600000-0x000000800000 : "spare" spi_davinci spi_davinci.1: Controller at 0xfef0e000 CAN device driver interface mcp251x spi1.1: probed davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask fffffff7 davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 ata1: SATA link down (SStatus 0 SControl 300) hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected i2c /dev entries driver cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver mmc0: new high speed SDHC card at address aaaa mmcblk0: mmc0:aaaa SA08G 7.40 GiB mmcblk0: p1 dsd1791 spi1.2: Failed to add route LLOUT->Line Out asoc: dsd1791 <-> davinci-mcasp.0 mapping ok ALSA device list: #0: MityDSP-L138 INDIO TCP cubic registered NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) regulator_init_complete: LDO2: incomplete constraints, leaving on regulator_init_complete: LDO1: incomplete constraints, leaving on regulator_init_complete: VDCDC3: incomplete constraints, leaving on regulator_init_complete: VDCDC2: incomplete constraints, leaving on regulator_init_complete: VDCDC1: incomplete constraints, leaving on console [netcon0] enabled netconsole: network logging started omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p1): using internal journal EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 179:1. devtmpfs: mounted Freeing init memory: 160K Failed to mount /sys/kernel/security: No such file or directory Welcome to The Ångström Distribution! NET: Registered protocol family 10 Starting LSB: The RPC portmapper... Starting Apply Kernel Variables... Started Huge Pages File System [ OK ] Started Set Up Additional Binary Formats [ OK ] Starting Debug File System... Starting POSIX Message Queue File System... Starting Load Kernel Modules... Starting Temporary Directory... Starting File System Check on Root Device... Starting udev Kernel Device Manager... Starting udev Coldplug all Devices... Starting Journal Service... Started Journal Service [ OK ] Starting Remount API VFS... udevd[1094]: starting version 182 Started udev Kernel Device Manager [ OK ] Started LSB: The RPC portmapper [ OK ] Started Apply Kernel Variables [ OK ] Started Debug File System [ OK ] Started POSIX Message Queue File System [ OK ] Started Load Kernel Modules [ OK ] Started Temporary Directory [ OK ] Started File System Check on Root Device [ OK ] Started Remount API VFS [ OK ] Starting Remount Root FS... Started Configuration File System [ OK ] Started FUSE Control File System [ OK ] Started Remount Root FS [ OK ] Starting Load Random Seed... Starting Recreate Volatile Files and Directories... Started Machine ID first boot configure [ OK ] Starting Run pending postinsts... Started Load Random Seed [ OK ] Started Recreate Volatile Files and Directories [ OK ] portmap[1080]: Starting portmap daemon... davinci_mdio davinci_mdio.0: resetting idled controller net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201) ADDRCONF(NETDEV_UP): eth0: link is not ready .---O---. | | .-. o o | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution mityomapl138 ttyS1 Angstrom v2012.05 - Kernel 3.2.0 mityomapl138 login: PHY: 0:03 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready