=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.10.21 09:43:24 =~=~=~=~=~=~=~=~=~=~=~= ÿ U-Boot SPL 2019.01-g3a254cb755-dirty (Mar 22 2024 - 16:41:18 +0530) DRA752-GP ES2.0 no pinctrl state for default mode ** Unable to read file dra7-ipu1-fw.xem4 ** Firmware loading failed Trying to boot from MMC1 no pinctrl state for default mode Loading Environment from FAT... *** Warning - bad CRC, using default environment Loading Environment from MMC... *** Warning - bad CRC, using default environment U-Boot 2019.01-g3a254cb755-dirty (Mar 22 2024 - 16:41:18 +0530) CPU : DRA752-GP ES2.0 Model: TI AM5748 IDK Board: MitySOM-57x Dev Kit Non-FPGA DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment Loading Environment from MMC... *** Warning - bad CRC, using default environment MitySOM-57x - Model No: 5728-PX-4AA-RI Serial No: 21005279 Part Number: 80-001446RI-3A Warning: fastboot.board_rev: unknown board revision i2c_write: error waiting for data ACK (status=0x116) cdce9xx_reg_write: failed for addr:5, ret:-121 board_set_pru_ethaddr Net: Could not get PHY for ethernet@48484000: addr 0 Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 2  1  0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** ** Unable to read file uEnv.txt ** switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 4469248 bytes read in 196 ms (21.7 MiB/s) 90157 bytes read in 5 ms (17.2 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe6000, end 8ffff02c ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.94-g7317dfbd4116-dirty (mitysom@mitysom-OptiPlex-5040) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #13 SMP PREEMPT Fri Mar 22 15:29:24 IST 2024 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Critical Link MitySOM-AM57x [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x000000009d000000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@9d000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009f000000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node dsp2-memory@9f000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 128 MiB at 0x00000000f6c00000 [ 0.000000] OMAP4: Map 0x00000000fed00000 to (ptrval) for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] random: get_random_bytes called from start_kernel+0xb4/0x470 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s32396 r8192 d20852 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 460096 [ 0.000000] Kernel command line: console=ttyS2,115200n8 cma=128MB drm.edid_firmware=edid/1920x1080.bin video=HDMI-A-1:1920x1080 root=PARTUUID=2798f9c1-02 rw rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1550312K/1847296K available (10240K kernel code, 337K rwdata, 2828K rodata, 2048K init, 272K bss, 34840K reserved, 262144K cma-reserved, 1160192K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 338 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 273 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000018] Switching to timer-based delay loop, resolution 162ns [ 0.000295] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000305] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000769] Console: colour dummy device 80x30 [ 0.000812] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000827] pid_max: default: 32768 minimum: 301 [ 0.000946] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000961] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001521] CPU: Testing write buffer coherency: ok [ 0.001557] CPU0: Spectre v2: using ICIALLU workaround [ 0.001767] /cpus/cpu@0 missing clock-frequency property [ 0.001787] /cpus/cpu@1 missing clock-frequency property [ 0.001800] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.059922] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.079932] rcu: Hierarchical SRCU implementation. [ 0.100121] EFI services will not be available. [ 0.119992] smp: Bringing up secondary CPUs ... [ 0.200368] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.200374] CPU1: Spectre v2: using ICIALLU workaround [ 0.200497] smp: Brought up 1 node, 2 CPUs [ 0.200508] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.200517] CPU: All CPU(s) started in HYP mode. [ 0.200525] CPU: Virtualization extensions available. [ 0.201085] devtmpfs: initialized [ 0.217636] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.217894] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.217913] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.222219] pinctrl core: initialized pinctrl subsystem [ 0.222743] DMI not present or invalid. [ 0.223018] NET: Registered protocol family 16 [ 0.224225] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.225145] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.418559] cpuidle: using governor ladder [ 0.418595] cpuidle: using governor menu [ 0.428662] OMAP GPIO hardware version 0.1 [ 0.453953] No ATAGs? [ 0.454026] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.454041] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.454883] OMAP DMA hardware revision 0.0 [ 0.466572] edma 43300000.edma: memcpy is disabled [ 0.469908] edma 43300000.edma: TI EDMA DMA engine driver [ 0.476918] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.563130] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.563315] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.563555] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.563785] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.564159] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.564338] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.564617] iommu: Adding device 58820000.ipu to group 1 [ 0.564697] iommu: Adding device 55020000.ipu to group 2 [ 0.564822] iommu: Adding device 40800000.dsp to group 0 [ 0.565047] iommu: Adding device 41000000.dsp to group 3 [ 0.566276] SCSI subsystem initialized [ 0.567334] palmas 0-0058: Irq flag is 0x00000008 [ 0.593522] palmas 0-0058: Muxing GPIO 2f, PWM 0, LED 0 [ 0.595156] SMPS12: supplied by regulator-dummy [ 0.596758] SMPS3: supplied by VMAIN [ 0.598246] SMPS45: supplied by regulator-dummy [ 0.599978] SMPS6: supplied by VMAIN [ 0.601569] SMPS7: supplied by VMAIN [ 0.603308] SMPS8: supplied by VMAIN [ 0.604893] SMPS9: supplied by VMAIN [ 0.605001] random: fast init done [ 0.605825] LDO1: supplied by VMAIN [ 0.631205] LDO2: supplied by VMAIN [ 0.651233] LDO3: supplied by VMAIN [ 0.671243] LDO4: supplied by VMAIN [ 0.671906] LDO5: supplied by regulator-dummy [ 0.672580] LDO6: supplied by regulator-dummy [ 0.673237] LDO7: supplied by regulator-dummy [ 0.673904] LDO8: supplied by regulator-dummy [ 0.674561] LDO9: supplied by VMAIN [ 0.691561] LDOLN: supplied by VMAIN [ 0.701292] LDOUSB: supplied by VMAIN [ 0.713758] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.714682] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 0.714884] media: Linux media interface: v0.10 [ 0.714923] videodev: Linux video capture interface: v2.00 [ 0.715001] pps_core: LinuxPPS API ver. 1 registered [ 0.715010] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.715030] PTP clock support registered [ 0.715060] EDAC MC: Ver: 3.0.0 [ 0.715826] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.716074] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.720899] Advanced Linux Sound Architecture Driver Initialized. [ 0.721720] clocksource: Switched to clocksource arch_sys_counter [ 0.729813] NET: Registered protocol family 2 [ 0.730396] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.730426] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.730489] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.730616] TCP: Hash tables configured (established 8192 bind 8192) [ 0.730687] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.730721] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.731004] NET: Registered protocol family 1 [ 0.751436] RPC: Registered named UNIX socket transport module. [ 0.751446] RPC: Registered udp transport module. [ 0.751454] RPC: Registered tcp transport module. [ 0.751462] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.752566] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.752761] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.753750] Initialise system trusted keyrings [ 0.753878] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.758828] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.769323] NFS: Registering the id_resolver key type [ 0.769347] Key type id_resolver registered [ 0.769356] Key type id_legacy registered [ 0.769397] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.771069] Key type asymmetric registered [ 0.771081] Asymmetric key parser 'x509' registered [ 0.771129] bounce: pool size: 64 pages [ 0.771163] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.771173] io scheduler noop registered [ 0.771182] io scheduler deadline registered [ 0.771277] io scheduler cfq registered (default) [ 0.771288] io scheduler mq-deadline registered [ 0.771297] io scheduler kyber registered [ 0.777058] pinctrl-single 4a003400.pinmux: 282 pins, size 1128 [ 0.784467] V3_3D: supplied by smps9 [ 0.784709] aic_dvdd: supplied by V3_3D [ 0.784774] vtt_fixed: supplied by V3_3D [ 0.831558] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.835126] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 43, base_baud = 3000000) is a 8250 [ 0.836072] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 44, base_baud = 3000000) is a 8250 [ 1.816543] console [ttyS2] enabled [ 1.820970] 4ae2b000.serial: ttyS9 at MMIO 0x4ae2b000 (irq = 45, base_baud = 3000000) is a 8250 [ 1.831893] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 1.832453] random: crng init done [ 1.841687] omapdss_dss 58000000.dss: Linked as a consumer to regulator.22 [ 1.848740] DSS: OMAP DSS rev 6.1 [ 1.855066] omapdss_hdmi5 58040000.encoder: Linked as a consumer to regulator.15 [ 1.862600] omapdss_hdmi5 58040000.encoder: Dropping the link to regulator.15 [ 1.882901] brd: module loaded [ 1.892235] loop: module loaded [ 1.901441] m25p80 spi0.0: found n25q256ax1, expected s25fl256s1 [ 1.907863] m25p80 spi0.0: n25q256ax1 (32768 Kbytes) [ 1.912953] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.919336] Creating 7 MTD partitions on "spi0.0": [ 1.924174] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 1.930052] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.936203] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 1.942952] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.949410] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 1.956600] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 1.962726] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 1.969905] libphy: Fixed MDIO Bus: probed [ 1.977240] i2c /dev entries driver [ 1.983902] gpio-fan gpio_fan: GPIO fan initialized [ 2.015443] cpu cpu0: Linked as a consumer to regulator.6 [ 2.020945] cpu cpu0: Linked as a consumer to regulator.29 [ 2.028142] sdhci: Secure Digital Host Controller Interface driver [ 2.034423] sdhci: Copyright(c) Pierre Ossman [ 2.039943] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.046284] omap_gpio 4805d000.gpio: Could not set line 27 debounce to 200000 microseconds (-22) [ 2.055139] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.059946] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.28 [ 2.066982] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.13 [ 2.074133] sdhci-omap 4809c000.mmc: Dropping the link to regulator.13 [ 2.080737] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.2 [ 2.087690] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.13 [ 2.094871] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_3_3v mode [ 2.127353] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.134960] sdhci-omap 480b4000.mmc: 480b4000.mmc supply vqmmc not found, using dummy regulator [ 2.143785] sdhci-omap 480b4000.mmc: Linked as a consumer to regulator.0 [ 2.150578] sdhci-omap 480b4000.mmc: Dropping the link to regulator.0 [ 2.158084] sdhci-omap 480b4000.mmc: Linked as a consumer to regulator.2 [ 2.164895] sdhci-omap 480b4000.mmc: no pinctrl state for ddr_1_8v mode [ 2.171553] sdhci-omap 480b4000.mmc: no pinctrl state for ddr_3_3v mode [ 2.178239] sdhci-omap 480b4000.mmc: no pinctrl state for hs mode [ 2.184388] sdhci-omap 480b4000.mmc: no pinctrl state for hs mode [ 2.190519] sdhci-omap 480b4000.mmc: no pinctrl state for hs200_1_8v mode [ 2.222533] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.230595] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.239096] ledtrig-cpu: registered to indicate activity on CPUs [ 2.245314] mmc0: new high speed SDXC card at address 59b4 [ 2.254018] ad799x 4-0029: Linked as a consumer to regulator.2 [ 2.259976] ad799x 4-0029: 4-0029 supply vref not found, using dummy regulator [ 2.261572] mmcblk0: mmc0:59b4 58.9 GiB [ 2.267396] ad799x 4-0029: Linked as a consumer to regulator.0 [ 2.280493] NET: Registered protocol family 10 [ 2.295558] Segment Routing with IPv6 [ 2.299301] mmcblk0: p1 p2 [ 2.299331] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.309300] NET: Registered protocol family 17 [ 2.314013] Key type dns_resolver registered [ 2.318498] Registering SWP/SWPB emulation handler [ 2.323346] omap_voltage_late_init: Voltage driver support not added [ 2.329736] Power Management for TI OMAP4+ devices. [ 2.329754] mmc1: new MMC card at address 0001 [ 2.335331] Loading compiled-in X.509 certificates [ 2.349821] mmcblk1: mmc1:0001 S0J56X 14.8 GiB [ 2.354813] mmcblk1boot0: mmc1:0001 S0J56X partition 1 31.5 MiB [ 2.361172] mmcblk1boot1: mmc1:0001 S0J56X partition 2 31.5 MiB [ 2.367284] mmcblk1rpmb: mmc1:0001 S0J56X partition 3 4.00 MiB, chardev (244:0) [ 2.367305] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.382158] dmm 4e000000.dmm: initialized all PAT entries [ 2.387642] mmcblk1: [ 2.390283] omapdss_hdmi5 58040000.encoder: Linked as a consumer to regulator.15 [ 2.397811] omapdss_hdmi5 58040000.encoder: Dropping the link to regulator.15 [ 2.406267] omapdss_hdmi5 58040000.encoder: Linked as a consumer to regulator.15 [ 2.414073] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops) [ 2.422079] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops) [ 2.430793] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.437455] [drm] No driver support for vblank timestamp query. [ 2.443438] [drm] Cannot find any crtc or sizes [ 2.448668] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0 [ 2.456239] hctosys: unable to open rtc device (rtc0) [ 2.461873] ALSA device list: [ 2.464853] No soundcards found. [ 3.014368] EXT4-fs (mmcblk0p2): recovery complete [ 3.022253] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.030440] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 3.044538] devtmpfs: mounted [ 3.048432] Freeing unused kernel memory: 2048K [ 3.053095] Run /sbin/init as init process [ 3.347674] systemd[1]: System time before build time, advancing clock. [ 3.367633] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 3.389935] systemd[1]: Detected architecture arm. Welcome to Arago 2019.11! [ 3.442658] systemd[1]: Set hostname to . [ 3.521815] [drm] Cannot find any crtc or sizes [ 3.619433] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 3.636669] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 3.837682] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 3.873036] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 3.901839] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 3.934351] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 3.965515] systemd[1]: Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Mounting Kernel Debug File System... [ OK ] Listening on udev Kernel Socket. Starting Load Kernel Modules... [ OK ] Created slice system-getty.slice. [ OK ] Listening on udev Control Socket. [ 4.167335] usbcore: registered new interface driver usbfs [ 4.172931] usbcore: registered new interface driver hub [ 4.178351] usbcore: registered new device driver usb Starting udev Coldplug all Devices... [ 4.197517] usbcore: registered new interface driver ftdi_sio [ 4.203546] usbserial: USB Serial support registered for FTDI USB Serial Device [ OK ] Reached target Slices. [ OK ] Listening on Process Core Dump Socket. [ OK ] Reached target Swap. Mounting Temporary Directory (/tmp)... [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Listening on Journal Socket (/dev/log). Starting Journal Service... [ OK ] Created slice system-serial\x2dgetty.slice. Mounting POSIX Message Queue File System... Starting Remount Root and Kernel File Systems... [ 4.541761] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Started Journal Service. [ OK ] Mounted Kernel Debug File System. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Remount Root and Kernel File Systems. Starting Create Static Device Nodes in /dev... Mounting Kernel Configuration File System... Starting Apply Kernel Variables... Starting Flush Journal to Persistent Storage... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Apply Kernel Variables. [ 5.039558] systemd-journald[100]: Received request to flush runtime journal from PID 1 [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... [ OK ] Reached target Containers. Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started udev Coldplug all Devices. [ OK ] Started udev Kernel Device Manager. [ OK ] Mounted /media/ram. [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories[ 5.477209] omap-rproc 58820000.ipu: ignoring dependency for device, assuming no driver . Starting Network Service... [ 5.521012] omap-rproc 58820000.ipu: ignoring dependency for device, assuming no driver [ 5.532127] omap-rproc 58820000.ipu: assigned reserved memory node ipu1-memory@9d000000 [ 5.553683] remoteproc remoteproc0: 58820000.ipu is available Starting Network Time Synchronization... [ 5.566021] omap-rproc 55020000.ipu: ignoring dependency for device, assuming no driver Starting Update UTMP about System Boot/Shutdown... [ 5.602180] omap-rproc 55020000.ipu: ignoring dependency for device, assuming no driver [ 5.610227] omap-rproc 55020000.ipu: assigned reserved memory node ipu2-memory@95800000 [ OK ] Found device /dev/ttyS2. [ 5.741265] remoteproc remoteproc1: 55020000.ipu is available [ 5.773742] omap-rproc 40800000.dsp: ignoring dependency for device, assuming no driver [ OK ] Started Update UTMP about System Boot/Shutdown. [ 5.810557] omap-rproc 40800000.dsp: ignoring dependency for device, assuming no driver [[ 5.863025] omap-rproc 40800000.dsp: assigned reserved memory node dsp1-memory@99000000  OK ] Found device /dev/ttyS0. [ 5.899337] remoteproc remoteproc2: 40800000.dsp is available [ 5.923367] remoteproc remoteproc0: powering up 58820000.ipu [ 5.929764] remoteproc remoteproc0: Booting fw image dra7-ipu1-fw.xem4, size 6849560 [ 5.938709] omap-rproc 41000000.dsp: ignoring dependency for device, assuming no driver [ 5.951124] Driver for 1-wire Dallas network protocol. [ 5.955421] virtio_rpmsg_bus virtio0: rpmsg host is online [ 5.963974] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: rtc core: registered 48070000.i2c:tps659038@58:tps659038_rtc as rtc0 [ 5.964146] omap-rproc 41000000.dsp: ignoring dependency for device, assuming no driver [ 5.990545] remoteproc remoteproc0: registered virtio0 (type 7) [ 6.002321] remoteproc remoteproc0: remote processor 58820000.ipu is now up [ 6.012453] omap-rproc 41000000.dsp: assigned reserved memory node dsp2-memory@9f000000 [ 6.020646] remoteproc remoteproc3: 41000000.dsp is available [ 6.035498] omap_gpio 48051000.gpio: Could not set line 25 debounce to 20000 microseconds (-22) [ 6.101765] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.:. Driver in Interrupt mode [ 6.186491] at24 0-0050: 4096 byte 24c32 EEPROM, read-only, 0 bytes/write [ 6.211549] at24 4-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write [ 6.324410] w1_master_driver w1_bus_master1: Attaching one wire slave 01.000000000000 crc 3d [ 6.336144] tlv320aic3x-codec 4-0018: Linked as a consumer to regulator.3 [ 6.345669] omap_rtc 48838000.rtc: registered as rtc1 [ 6.352371] tlv320aic3x-codec 4-0018: Linked as a consumer to regulator.2 [ 6.388449] w1_master_driver w1_bus_master1: Family 1 for 01.000000000000.3d is not registered. [ 6.530252] remoteproc remoteproc1: powering up 55020000.ipu [ 6.535999] remoteproc remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 4808704 [ 6.543894] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1 [ 6.567890] virtio_rpmsg_bus virtio1: rpmsg host is online [ 6.573469] remoteproc remoteproc1: registered virtio1 (type 7) [ 6.575042] virtio_rpmsg_bus virtio1: creating channel rpmsg-client-sample addr 0x32 [ 6.579412] remoteproc remoteproc1: remote processor 55020000.ipu is now up [ 6.596371] virtio_rpmsg_bus virtio1: creating channel rpmsg-client-sample addr 0x33 [ 6.604896] virtio_rpmsg_bus virtio1: creating channel rpmsg-omx addr 0x3c [ 6.612606] virtio_rpmsg_bus virtio1: creating channel rpmsg-rpc addr 0x65 [ 6.620414] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 6.627608] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ 6.633990] omap-des 480a5000.des: will run requests pump with realtime priority [ 6.644587] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 6.752223] phy phy-4a084000.phy.3: Linked as a consumer to regulator.23 [ 6.771615] phy phy-4a085000.phy.4: Linked as a consumer to regulator.23 [ OK ] Started Network Time Synchronization. [ OK ] Started Network Service. Starting Wait for Network to be Configured... Starting Network Name Resolution... [ 6.954225] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ 6.969054] omap-aes 4b500000.aes: will run requests pump with realtime priority [ OK ] Reached target System Initialization. [ 6.977642] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 6.990938] omap-aes 4b700000.aes: will run requests pump with realtime priority [ OK ] Listening on RPCbind Server Activation Socket. Starting Reboot and dump vmcore via kexec... [ OK ] Started Daily Cleanup of Temporary Directories. [ 7.278047] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin [ 7.377269] ahci 4a140000.sata: controller can't do 64bit DMA, forcing 32bit [ 7.384546] ahci 4a140000.sata: forcing port_map 0x0 -> 0x1 [ 7.394880] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 7.394968] omap-hdmi-audio omap-hdmi-audio.0.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok [ 7.407844] ahci 4a140000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 7.429872] omap-hdmi-audio omap-hdmi-audio.0.auto: ASoC: no DMI vendor name! [ 7.450554] scsi host0: ahci [ 7.453795] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 82 [ 7.492602] vpe 489d0000.vpe: Device registered as /dev/video0 [ 7.517019] omap_gpio 48051000.gpio: Could not set line 24 debounce to 20000 microseconds (-22) [ OK ] Listening on D-Bus System Message Bus Socket. [ 7.795098] ata1: SATA link down (SStatus 0 SControl 300) [ OK ] Listening on dropbear.socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting TI MultiCore Tools Daemon... [ 8.106765] asoc-simple-card sound0: tlv320aic3x-hifi <-> 4847c000.mcasp mapping ok [ OK ] Started Periodic Command Scheduler. [ 8.118274] asoc-simple-card sound0: ASoC: no DMI vendor name! Starting Print notice about GPLv3 packages... [ OK ] Started D-Bus System Message Bus. Starting TI IPC Daemon... Starting Login Service... [ OK ] Started Job spooling tools. [ 8.193674] remoteproc remoteproc2: powering up 40800000.dsp Starting RPC Bind Service... Starting rc.pvr.service... [ OK ] Reached[ 8.221261] remoteproc remoteproc2: Booting fw image dra7-dsp1-fw.xe66, size 20360464 target System Time Synchronized. [ 8.239511] omap-iommu 40d01000.mmu: 40d01000.mmu: version 3.0 [ 8.245448] omap-iommu 40d02000.mmu: 40d02000.mmu: version 3.0 [ 8.254715] remoteproc remoteproc3: powering up 41000000.dsp [ 8.260434] remoteproc remoteproc3: Booting fw image dra7-dsp2-fw.xe66, size 20360464 [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. [ OK ] Started Network Name Resolution. [ 8.291810] omap-iommu 41501000.mmu: 41501000.mmu: version 3.0 [ 8.292039] davinci_mdio 4b2b2400.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 8.297739] omap-iommu 41502000.mmu: 41502000.mmu: version 3.0 [ 8.342491] virtio_rpmsg_bus virtio2: rpmsg host is online [ 8.349909] remoteproc remoteproc2: registered virtio2 (type 7) [ 8.349915] remoteproc remoteproc2: remote processor 40800000.dsp is now up [ 8.378376] libphy: 4b2b2400.mdio: probed [ 8.378978] virtio_rpmsg_bus virtio2: creating channel rpmsg-proto addr 0x3d [ 8.399199] virtio_rpmsg_bus virtio3: rpmsg host is online [ 8.399262] remoteproc remoteproc3: registered virtio3 (type 7) [ 8.399268] remoteproc remoteproc3: remote processor 41000000.dsp is now up [ 8.402481] virtio_rpmsg_bus virtio3: creating channel rpmsg-proto addr 0x3d [ 8.414047] davinci_mdio 4b2b2400.mdio: phy[0]: device 4b2b2400.mdio:00, driver unknown [ 8.414053] davinci_mdio 4b2b2400.mdio: phy[1]: device 4b2b2400.mdio:01, driver unknown [ 8.444484] remoteproc remoteproc4: 4b234000.pru is available [ OK ] Started Reboot and dump vmcore via kexec. [ OK ] Started TI IPC Daemon. [FAILED] Failed to start TI MultiCore Tools Daemon. See 'systemctl status ti-mct-daemon.service' for details. [ OK ] Started RPC Bind Service. [ 8.762270] pru-rproc 4b234000.pru: PRU rproc node pru@4b234000 probed successfully [ 8.819128] remoteproc remoteproc5: 4b238000.pru is available [ 8.840625] pru-rproc 4b238000.pru: PRU rproc node pru@4b238000 probed successfully [ 8.897661] remoteproc remoteproc6: 4b2b4000.pru is available [ 8.953515] pru-rproc 4b2b4000.pru: PRU rproc node pru@4b2b4000 probed successfully [ 9.028336] remoteproc remoteproc7: 4b2b8000.pru is available [ 9.093173] pru-rproc 4b2b8000.pru: PRU rproc node pru@4b2b8000 probed successfully [ 9.202267] prueth pruss2_eth: port 2: using random MAC addr: ba:87:c1:29:74:c0 [ 9.253791] prueth pruss2_eth: pruss_fw_drop_untagged_vlan 0 [ 9.291751] prueth pruss2_eth: pruss MC Mask (Port 0) ff:ff:ff:ff:ff:ff [ 9.298406] prueth pruss2_eth: pruss MC Mask (Port 1) ff:ff:ff:ff:ff:ff [ 9.381294] prueth pruss2_eth: TI PRU ethernet (type 0) driver initialized [ 10.287048] dwc3 48890000.usb: Failed to get clk 'ref': -2 [ 10.327568] rpmsg_rpc virtio1.rpmsg-rpc.-1.101: probing service rpc_example_1 with src 1024 dst 101 [ 10.346656] dwc3 488d0000.usb: Failed to get clk 'ref': -2 [ 10.352633] dwc3 48890000.usb: changing max_speed on rev 5533202a [ 10.392885] rpmsg_rpc virtio1.rpmsg-rpc.-1.101: published functions = 8 [ 10.510585] NET: Registered protocol family 45 [ 10.555802] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 10.613251] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 10.630332] iep ptp bc clkid -1 [ 10.633882] remoteproc remoteproc7: powering up 4b2b8000.pru [ 10.666418] remoteproc remoteproc7: Booting fw image ti-pruss/am57xx-pru1-prueth-fw.elf, size 7256 [ 10.676147] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 10.697780] pruss 4b280000.pruss: configured system_events[63-0] = 00600000,08a00000 [ 10.705131] xhci-hcd xhci-hcd.1.auto: irq 193, io mem 0x488d0000 [ 10.722191] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 10.730642] pruss 4b280000.pruss: configured intr_channels = 0x0000032a host_intr = 0x000002aa [ 10.734523] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.757943] usb usb1: Product: xHCI Host Controller [ 10.758511] remoteproc remoteproc7: remote processor 4b2b8000.pru is now up [ 10.767544] usb usb1: Manufacturer: Linux 4.19.94-g7317dfbd4116-dirty xhci-hcd [ 10.777585] usb usb1: SerialNumber: xhci-hcd.1.auto [ 10.785519] hub 1-0:1.0: USB hub found [ 10.792012] hub 1-0:1.0: 1 port detected [ 10.796451] net eth1: started [ OK ] Started rc.pvr.service. [ 10.805909] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 10.808213] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 10.819299] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 10.827828] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 10.835158] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 10.844666] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19 [ 10.853398] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.854227] remoteproc remoteproc6: powering up 4b2b4000.pru [ 10.867361] usb usb2: Product: xHCI Host Controller [ 10.873555] usb usb2: Manufacturer: Linux 4.19.94-g7317dfbd4116-dirty xhci-hcd [ 10.873786] remoteproc remoteproc6: Booting fw image ti-pruss/am57xx-pru0-prueth-fw.elf, size 7228 [ 10.880810] usb usb2: SerialNumber: xhci-hcd.1.auto [ 10.895481] pruss 4b280000.pruss: configured system_events[63-0] = 00000600,04500000 [ 10.895635] hub 2-0:1.0: USB hub found [ 10.903757] pruss 4b280000.pruss: configured intr_channels = 0x000000d5 host_intr = 0x00000155 [ 10.915785] hub 2-0:1.0: 1 port detected [ 10.916011] remoteproc remoteproc6: remote processor 4b2b4000.pru is now up [ 10.927180] net eth0: started [ 10.931686] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: autoconf bash-dev bash bc binutils-dev binutils bison-dev bison cifs-utils cpio cpp-symlinks cpp dosfstools elfutils-dev elfutils findutils g++-symlinks g++ gawk gcc-symlinks gcc gdb gdbc6x gdbserver gettext glmark2 gstreamer1.0-libav gzip hidapi libasm1 libbfd libcairo-perf-utils libdw1 libelf1 libgdbm-compat4 libgdbm-dev libgdbm6 libgettextlib libgettextsrc libgmp10 libidn2-0 libmavconn libmpc3 libmpfr6 libreadline-dev libreadline7 libunistring2 m4-dev m4 make mavlink mavros-extras mavros-msgs mavros nettle parted pdm-anomaly-detection rsync socketcan-interface swig-dev swig which If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. [ 12.935035] NOHZ: local_softirq_pending 08 [ 12.966402] NOHZ: local_softirq_pending 08 [ 13.052621] prueth pruss2_eth eth0: Link is Up - 100Mbps/Full - flow control off [ 13.060122] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 13.231548] NOHZ: local_softirq_pending 08 Starting Save/Restore Sound Card State... [ 13.935460] NOHZ: local_softirq_pending 08 [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Starting weston.service... [ OK ] Created slice system-systemd\x2dfsck.slice. Starting File System Check on /dev/mmcblk0p1... [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Network. [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started Redis In-Memory Data Store. Starting Lightning Fast Webserver With Light System Requirements... Starting Simple Network Management Protocol (SNMP) Daemon.... Starting Enable and configure wl18xx bluetooth stack... Starting Permit User Sessions... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Save/Restore Sound Card State. [ OK ] Started File System Check on /dev/mmcblk0p1. [ OK ] Started Enable and configure wl18xx bluetooth stack. [ OK ] Started Permit User Sessions. [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS2. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. Starting Synchronize System and HW clocks... Mounting /run/media/mmcblk0p1... [ OK ] Reached target Sound Card. [ OK ] Started Synchronize System and HW clocks. [ OK ] Started Login Service. [ OK ] Mounted /run/media/mmcblk0p1. [ OK ] Started Simple Network Management Protocol (SNMP) Daemon.. [ 14.935892] NOHZ: local_softirq_pending 08 [ 15.232521] NOHZ: local_softirq_pending 08 [ 15.248571] NOHZ: local_softirq_pending 08 [ 15.467803] NOHZ: local_softirq_pending 08 [ 15.514476] NOHZ: local_softirq_pending 08 [ 15.545819] NOHZ: local_softirq_pending 08 [ OK ] Started weston.service. Starting Matrix GUI... Starting telnetd.service... [ OK ] Started Matrix GUI. [ OK ] Started telnetd.service. Starting thttpd.service... [ OK ] Started thttpd.service. [ OK ] Created slice system-systemd\x2dcoredump.slice. [ OK ] Started Process Core Dump (PID 1051/UID 0). _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org mitysom-am57x ttyS2 Arago 2019.11 mitysom-am57x ttyS2 mitysom-am57x login: root 78root@mitysom-am57x:~# [ 32.481777] aic_dvdd: disabling