U-Boot 2009.11-00162-g649c446 (Jun 28 2010 - 08:12:30) I2C: ready DRAM: 128 MB NAND: 256 MiB In: serial Out: serial Err: serial ARM Clock : 300000000 Hz DDR Clock : 132000000 Hz EMIFA CLock : 100000000 Hz DSP Clock : 300000000 Hz ASYNC3 Clock : 150000000 Hz Enet config : 2 Resetting ethernet phy Net: Ethernet PHY: GENERIC @ 0x03 [0x8] Hit any key to stop autoboot: 0 8192 KiB M25P64 at 0:0 is now current device 8192 KiB M25P64 at 0:0 is now current device ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-2.6.34-rc1-07430-g2e70fb6 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1818012 Bytes = 1.7 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Linux version 2.6.34-rc1-07430-g2e70fb6 (mikew@mikew-ubuntu-vm) (gcc version 4.3 .3 (GCC) ) #114 PREEMPT Fri Jun 25 13:44:48 EDT 2010 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: MityDSP-L138 Peripheral Config Block Found Enet_Config = 2 EMAC = 00:50:C2:BF:83:24 PHYMask = 0x8 No LCD Configured UART[0] = 0, 0, 0, 115200 UART[1] = 1, 1, 0, 115200 UART[2] = 0, 0, 0, 115200 SPI[0] = 0, 0, 00, 0, 0 SPI[1] = 1, 1, 01, 0, 30000000 Memory policy: ECC disabled, Data cache writethrough DaVinci da850/omap-l138 variant 0x0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),- (userfs) root=/dev/mtdblock0 rw rootfstype=jffs2 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 93652k/93652k available, 4652k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xff000000 - 0xffe00000 ( 14 MB) vmalloc : 0xc6800000 - 0xfea00000 ( 898 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0028000 ( 128 kB) .text : 0xc0028000 - 0xc034d000 (3220 kB) .data : 0xc0364000 - 0xc0384f80 ( 132 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 start_kernel(): bug: interrupts were enabled early Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs regulator: core version 0.5 NET: Registered protocol family 16 mityomapl138_init... mityomapl138_init: no LCD device enabled MUX: initialized MMCSD0_DAT_0 MUX: Setting register MMCSD0_DAT_0 PINMUX10 (0x00000028) = 0x00000000 -> 0x00000200 MUX: initialized MMCSD0_DAT_1 MUX: Setting register MMCSD0_DAT_1 PINMUX10 (0x00000028) = 0x00000200 -> 0x00002200 MUX: initialized MMCSD0_DAT_2 MUX: Setting register MMCSD0_DAT_2 PINMUX10 (0x00000028) = 0x00002200 -> 0x00022200 MUX: initialized MMCSD0_DAT_3 MUX: Setting register MMCSD0_DAT_3 PINMUX10 (0x00000028) = 0x00022200 -> 0x00222200 MUX: initialized MMCSD0_CLK MUX: Setting register MMCSD0_CLK PINMUX10 (0x00000028) = 0x00222200 -> 0x00222202 MUX: initialized MMCSD0_CMD MUX: Setting register MMCSD0_CMD PINMUX10 (0x00000028) = 0x00222202 -> 0x00222222 MUX: initialized GPIO4_0 MUX: Setting register GPIO4_0 PINMUX10 (0x00000028) = 0x00222222 -> 0x80222222 MUX: initialized GPIO4_1 MUX: Setting register GPIO4_1 PINMUX10 (0x00000028) = 0x80222222 -> 0x88222222 MUX: initialized AHCLKX MUX: Setting register AHCLKX PINMUX0 (0x00000000) = 0x00440000 -> 0x00140000 MUX: initialized ACLKX MUX: Setting register ACLKX PINMUX0 (0x00000000) = 0x00140000 -> 0x00140010 MUX: initialized AFSX MUX: Setting register AFSX PINMUX0 (0x00000000) = 0x00140010 -> 0x00141010 MUX: initialized AHCLKR MUX: Setting register AHCLKR PINMUX0 (0x00000000) = 0x00141010 -> 0x00111010 MUX: initialized ACLKR MUX: Setting register ACLKR PINMUX0 (0x00000000) = 0x00111010 -> 0x00111011 MUX: initialized AFSR MUX: Setting register AFSR PINMUX0 (0x00000000) = 0x00111011 -> 0x00111111 MUX: initialized AMUTE MUX: Setting register AMUTE PINMUX0 (0x00000000) = 0x00111111 -> 0x01111111 MUX: initialized AXR_13 MUX: Setting register AXR_13 PINMUX1 (0x00000004) = 0x00000000 -> 0x00000100 bio: create slab at 0 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb regulator: VDCDC1: 1150 <--> 1350 mV at 1225 mV regulator: VDCDC2: 1710 <--> 1910 mV at 3300 mV regulator: VDCDC3: 1120 <--> 1320 mV at 1800 mV regulator: LDO1: 1800 mV regulator: LDO2: 3300 mV Switching to clocksource timer0_1 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. EMAC: MII PHY configured, RMII PHY will not be functional mityomapl138_init: setting phy_mask to 8 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 182 io scheduler noop registered (default) Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM (writable) NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB 3,3V 16-bi t) Creating 2 MTD partitions on "davinci_nand.0": 0x000000000000-0x000008000000 : "rootfs" mtd: Giving out device 0 to rootfs ftl_cs: FTL header not found. 0x000008000000-0x000010000000 : "homefs" mtd: Giving out device 1 to homefs ftl_cs: FTL header not found. davinci_nand davinci_nand.0: controller rev. 2.5 m25p80 spi1.0: m25p64 (8192 Kbytes) Creating 3 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "UBL" mtd: Giving out device 2 to UBL ftl_cs: FTL header not found. 0x000000010000-0x000000090000 : "U-Boot" mtd: Giving out device 3 to U-Boot ftl_cs: FTL header not found. 0x000000090000-0x000000800000 : "Spare" mtd: Giving out device 4 to Spare ftl_cs: FTL header not found. spi_davinci spi_davinci.1: Controller at 0xfef0e000 console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: DA8xx OHCI usb usb1: Manufacturer: Linux 2.6.34-rc1-07430-g2e70fb6 ohci_hcd usb usb1: SerialNumber: ohci.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected mice: PS/2 mouse device common for all mice omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected omap_rtc: already running i2c /dev entries driver watchdog watchdog: heartbeat 60 sec cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused i2c1 Clocks: disable unused emac Clocks: disable unused mcasp Clocks: disable unused lcdc Clocks: disable unused mmcsd Clocks: disable unused spi0 Clocks: disable unused mcbsp0 Clocks: disable unused mcbsp1 Clocks: disable unused vpif regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on regulator_init_complete: incomplete constraints, leaving VDCDC3 on regulator_init_complete: incomplete constraints, leaving VDCDC2 on regulator_init_complete: incomplete constraints, leaving VDCDC1 on emac-mii: probed omap_rtc omap_rtc: setting system clock to 2010-05-09 21:18:43 UTC (1273439923) Empty flash at 0x007cff44 ends at 0x007d0000 jffs2_scan_inode_node(): CRC failed on node at 0x061347d4: Read 0xffffffff, calc ulated 0x78efc9db Empty flash at 0x061348f8 ends at 0x06135000 Empty flash at 0x069a4318 ends at 0x069a4800 VFS: Mounted root (jffs2 filesystem) on device 31:0. Freeing init memory: 128K INIT: version 2.86 booting Please wait: booting... Starting udev udev: starting version 151 Remounting root file system... Caching udev devnodes Populating dev cachemv: cannot rename '/tmp/uname': No such file or directory root: mount: mount point /proc/bus/usb does not exist Configuring network interfaces... eth0: attached PHY driver [Generic PHY] (mii_b us:phy_addr=1:03, id=40005201) udhcpc (v1.13.2) started run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1 Sending discover... Sending discover... Sending discover... JFFS2 notice: (1045) check_node_data: wrong data CRC in data node at 0x006d8a98: read 0xb9a89bec, calculated 0x4b82af42. No lease, failing done. Starting portmap daemon: portmap. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution mityomapl138 ttyS1 Angstrom 2010.4-test-20100508 mityomapl138 ttyS1 mityomapl138 login: JFFS2 notice: (1045) check_node_data: wrong data CRC in data node at 0x029c2dcc: read 0xec47f2fc, calculated 0x5263b2b2. JFFS2 notice: (1045) check_node_data: wrong data CRC in data node at 0x069a3f44: read 0x4a677306, calculated 0x6e113e42.