, pgdat c05f7af0, node_mem_map c0626000 DMA zone: 192 pages used for memmap DMA zone: 0 pages reserved DMA zone: 24384 pages, LIFO batch:3 pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384 Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/sda1 rw,rootwait PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 96MB = 96MB total Memory: 91100k/91100k available, 7204k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc6800000 - 0xfea00000 ( 898 MB) lowmem : 0xc0000000 - 0xc6000000 ( 96 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc056b814 (5519 kB) .init : 0xc056c000 - 0xc0598000 ( 176 kB) .data : 0xc0598000 - 0xc05f8560 ( 386 kB) .bss : 0xc05f8584 - 0xc0625894 ( 181 kB) NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 148.88 BogoMIPS (lpj=744448) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok devtmpfs: initialized DaVinci: 144 gpio irqs print_constraints: dummy: NET: Registered protocol family 16 baseboard_pre_init: Entered mityomapl138_setup_nand: using 8 bit data baseboard_init [IndustrialIO]... bio: create slab at 0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV print_constraints: VDCDC2: 1800 mV print_constraints: VDCDC3: 1200 mV print_constraints: LDO1: 1800 mV print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV Advanced Linux Sound Architecture Driver Version 1.0.24. Switching to clocksource timer0_1 musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) Waiting for USB PHY clock good... musb-hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn) musb-hdrc: MHDRC RTL version 1.800 musb-hdrc: setup fifo_mode 2 musb-hdrc: 7/9 max ep, 2624/4096 memory musb-hdrc musb-hdrc: MUSB HDRC host driver musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1 musb-hdrc musb-hdrc: supports USB remote wakeup usb usb1: default language 0x0409 usb usb1: udev 1, busnum 1, minor = 0 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: MUSB HDRC host driver usb usb1: Manufacturer: Linux 3.2.0 musb-hcd usb usb1: SerialNumber: musb-hdrc usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected hub 1-0:1.0: standalone hub hub 1-0:1.0: individual port power switching hub 1-0:1.0: no over-current protection hub 1-0:1.0: Single TT hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) hub 1-0:1.0: power on to power good time: 10ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports musb-hdrc musb-hdrc: USB Host mode controller at fee00000 using DMA, IRQ 58 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 177 io scheduler noop registered (default) start plist test end plist test hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 1-1: new high-speed USB device number 2 using musb-hdrc usb 1-1: default language 0x0409 usb 1-1: udev 2, busnum 1, minor = 1 usb 1-1: New USB device found, idVendor=8564, idProduct=4000 usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=5 usb 1-1: Product: GL3220 usb 1-1: Manufacturer: Genesys usb 1-1: SerialNumber: 000000059 usb 1-1: usb_probe_device usb 1-1: configuration #1 chosen from 1 choice usb 1-1: adding 1-1:1.0 (config #1, interface 0) hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 hub 1-0:1.0: port 1 enable change, status 00000503 Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A console [ttyS1] enabled serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A brd: module loaded at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write MityOMAPL138: Found MAC = 00:50:c2:e6:7a:a1 MityOMAPL138: Part Number = L138-FI-236-RL ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67 ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP) Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 Creating 2 MTD partitions on "davinci_nand.1": 0x000000000000-0x000008000000 : "rootfs" 0x000008000000-0x000020000000 : "homefs" davinci_nand davinci_nand.1: controller rev. 2.5 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 ------------[ cut here ]------------ WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x54/0x108() autorequest GPIO-8 Modules linked in: [] (unwind_backtrace+0x0/0xec) from [] (warn_slowpath_common+0x4c/0x64) [] (warn_slowpath_common+0x4c/0x64) from [] (warn_slowpath_fmt+0x30/0x40) [] (warn_slowpath_fmt+0x30/0x40) from [] (gpio_ensure_requested+0x54/0x108) [] (gpio_ensure_requested+0x54/0x108) from [] (gpio_direction_output+0x80/0x140) [] (gpio_direction_output+0x80/0x140) from [] (davinci_spi_probe+0x334/0x47c) [] (davinci_spi_probe+0x334/0x47c) from [] (platform_drv_probe+0x1c/0x24) [] (platform_drv_probe+0x1c/0x24) from [] (driver_probe_device+0xd8/0x1c8) [] (driver_probe_device+0xd8/0x1c8) from [] (__driver_attach+0x60/0x84) [] (__driver_attach+0x60/0x84) from [] (bus_for_each_dev+0x4c/0x8c) [] (bus_for_each_dev+0x4c/0x8c) from [] (bus_add_driver+0xa0/0x220) [] (bus_add_driver+0xa0/0x220) from [] (driver_register+0xbc/0x148) [] (driver_register+0xbc/0x148) from [] (do_one_initcall+0x94/0x164) [] (do_one_initcall+0x94/0x164) from [] (kernel_init+0x78/0x120) [] (kernel_init+0x78/0x120) from [] (kernel_thread_exit+0x0/0x8) ---[ end trace c1fc27cd4f832e8a ]--- spi_davinci spi_davinci.1: registered master spi1 spi spi1.0: setup mode 0, 8 bits/w, 30000000 Hz max --> 0 m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes) Creating 8 MTD partitions on "m25p80": 0x000000000000-0x000000010000 : "ubl" 0x000000010000-0x000000090000 : "u-boot" 0x000000090000-0x0000000a0000 : "u-boot-env" 0x0000000a0000-0x0000000b0000 : "periph-config" No LCD configured MII PHY configured 0x0000000b0000-0x000000100000 : "reserved" 0x000000100000-0x000000400000 : "kernel" 0x000000400000-0x000000600000 : "fpga" 0x000000600000-0x000000800000 : "spare" spi_davinci spi_davinci.1: registered child spi1.0 spi spi1.1: setup mode 0, 8 bits/w, 1000000 Hz max --> 0 spi_davinci spi_davinci.1: registered child spi1.1 spi_davinci spi_davinci.1: Controller at 0xfef0e000 CAN device driver interface ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask fffffff7 ata1.00: ATA-8: WDC WD1600BEKT-00PVMT0, 01.01A01, max UDMA/133 ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32) davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 64 td 64 ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 2 ohci ohci.0: starting USB controller Waiting for USB PHY clock good... ohci ohci.0: created debug files ohci ohci.0: irq 59, io mem 0x01e25000 ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEKT-0 01.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write Protect is off ohci ohci.0: OHCI controller state ohci ohci.0: OHCI 1.0, NO legacy support registers ohci ohci.0: control 0x083 HCFS=operational CBSR=3 ohci ohci.0: cmdstatus 0x00000 SOC=0 ohci ohci.0: intrstatus 0x00000000 ohci ohci.0: intrenable 0x8000005a MIE RHSC UE RD WDH ohci ohci.0: hcca frame #0000 ohci ohci.0: roothub.a 00001202 POTPGT=0 NOCP NPS NDP=2(1) ohci ohci.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci ohci.0: roothub.status 00008000 DRWE ohci ohci.0: roothub.portstatus [0] 0x00000100 PPS usb usb2: default language 0x0409 usb usb2: udev 1, busnum 2, minor = 128 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA usb usb2: Product: DA8xx OHCI usb usb2: Manufacturer: Linux 3.2.0 ohci_hcd usb usb2: SerialNumber: ohci.0 usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: no over-current protection hub 2-0:1.0: power on to power good time: 0ms hub 2-0:1.0: local power source is good hub 2-0:1.0: trying to enable port power on non-switchable hub ohci ohci.0: SetPortFeature(1): POWER uas 1-1:1.0: usb_probe_interface uas 1-1:1.0: usb_probe_interface - got id usbcore: registered new interface driver uas Initializing USB Mass Storage driver... usb-storage 1-1:1.0: usb_probe_interface usb-storage 1-1:1.0: usb_probe_interface - got id usb-storage: USB Mass Storage device detected usb-storage: -- associate_dev usb-storage: Vendor: 0x8564, Product: 0x4000, Revision: 0x0008 usb-storage: Interface Subclass: 0x06, Protocol: 0x50 usb-storage: Transport: Bulk usb-storage: Protocol: Transparent SCSI scsi1 : usb-storage 1-1:1.0 usb-storage: *** thread sleeping. usb-storage 1-1:1.0: device found usb-storage 1-1:1.0: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-cypress usbcore: registered new interface driver ums-datafab usbcore: registered new interface driver ums_eneub6250 usbcore: registered new interface driver ums-freecom usbcore: registered new interface driver ums-isd200 usbcore: registered new interface driver ums-jumpshot usbcore: registered new interface driver ums-onetouch usbcore: registered new interface driver ums-realtek usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 usbcore: registered new interface driver ums-usbat ohci ohci.0: GetPortStatus(1) hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000 mousedev: PS/2 mouse device common for all mice omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected i2c /dev entries driver davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode davinci_mmc davinci_mmc.1: Using DMA, 4-bit mode VUB300 Driver rom wait states = 1C irqpoll timeout = 0400 usbcore: registered new interface driver vub300 usbcore: registered new interface driver ushc usbcore: registered new interface driver usbhid usbhid: USB HID core driver mmc0: new high speed SDHC card at address 0001 mmcblk0: mmc0:0001 00000 14.6 GiB mmcblk0: p1 ALSA device list: No soundcards found. TCP cubic registered NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) regulator_init_complete: LDO2: incomplete constraints, leaving on regulator_init_complete: LDO1: incomplete constraints, leaving on regulator_init_complete: VDCDC3: incomplete constraints, leaving on regulator_init_complete: VDCDC2: incomplete constraints, leaving on regulator_init_complete: VDCDC1: incomplete constraints, leaving on console [netcon0] enabled netconsole: network logging started omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) kjournald starting. Commit interval 5 seconds EXT3-fs (sda1): using internal journal ext3_orphan_cleanup: deleting unreferenced inode 9093135 EXT3-fs (sda1): 1 orphan inode deleted EXT3-fs (sda1): recovery complete usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1 usb-storage: GetMaxLUN command result is 1, data is 2 usb-storage 1-1:1.0: scan complete EXT3-fs (sda1): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 8:1. devtmpfs: mounted Freeing init memory: 176K NET: Registered protocol family 10 >udevd[1130]: starting version 182 udc_core: exports duplicate symbol usb_add_gadget_udc (owned by kernel) EXT3-fs (mmcblk0): error: can't find ext3 filesystem on dev mmcblk0. EXT2-fs (mmcblk0): error: can't find an ext2 filesystem on dev mmcblk0. FAT-fs (mmcblk0): bogus number of reserved sectors FAT-fs (mmcblk0): Can't find a valid FAT filesystem VFS: Can't find a Minix filesystem V1 | V2 | V3 on device mmcblk0. cramfs: wrong magic FAT-fs (mmcblk0): bogus number of reserved sectors FAT-fs (mmcblk0): Can't find a valid FAT filesystem kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p1): using internal journal EXT3-fs (mmcblk0p1): recovery complete EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode davinci_mdio davinci_mdio.0: resetting idled controller net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201) ADDRCONF(NETDEV_UP): eth0: link is not ready PHY: 0:03 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present