U-Boot SPL 2013.01.01 (Apr 23 2014 - 11:57:02) BOARD : Critical Link MitySOM-5CSX Module INFO : Watchdog enabled SDRAM: Initializing MMR registers SDRAM: Calibrating PHY SEQ.C: Preparing to start memory calibration SEQ.C: CALIBRATION PASSED SDRAM: ECC Enabled ALTERA DWMMC: 0 U-Boot 2013.01.01 (Apr 23 2014 - 11:57:17) Critical Link MitySOM-5CSX CPU : Altera SOCFPGA Platform BOARD : Critical Link MitySOM-5CSX Module I2C: ready DRAM: 1 GiB MMC: ALTERA DWMMC: 0 In: serial Out: serial Err: serial Net: mii0 preboot reading MMC uBoot ENV data ** File not found /etc/uBootStatic.env ** ## Info: input data size = 77 = 0x4D ** File not found /etc/uBoot.env ** ## Info: input data size = 77 = 0x4D ...done Hit any key to stop autoboot: 0 gpio: pin 28 (bank/mask = 0/0x10000000) gpio: pin 28 (gpio 28) value is 0 gpio: pin 28 (bank/mask = 0/0x10000000) gpio: pin 28 (gpio 28) value is 1 gpio: pin 0 (bank/mask = 0/0x00000001) gpio: pin 0 (gpio 0) value is 1 gpio: pin 9 (bank/mask = 0/0x00000200) gpio: pin 9 (gpio 9) value is 0 gpio: pin 9 (bank/mask = 0/0x00000200) gpio: pin 9 (gpio 9) value is 1 7007184 bytes read in 2389 ms (2.8 MiB/s) ## Starting application at 0x3FF7F330 ... ## Application terminated, rc = 0xA 3495680 bytes read in 1192 ms (2.8 MiB/s) 18391 bytes read in 25 ms (717.8 KiB/s) ## Booting kernel from Legacy Image at 00007fc0 ... Image Name: Linux-3.12.0-g456859b Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3495616 Bytes = 3.3 MiB Load Address: 00008000 Entry Point: 00008000 ## Flattened Device Tree blob at 00000100 Booting using the fdt blob at 0x00000100 XIP Kernel Image ... OK OK Loading Device Tree to 03ff8000, end 03fff7d6 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Linux version 3.12.0-g456859b (user@MitySOM-Dev) (gcc version 4.8.1 (GCC) ) #2 SMP Mon Jan 19 02:25:13 EST 2015 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Altera SOCFPGA, model: MitySOM-5CSX Altera SOCFPGA Cyclone V Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 8 pages/cpu @80b80000 s11328 r8192 d13248 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait mem=512M PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512008K/524288K available (5266K kernel code, 261K rwdata, 1472K rodata, 347K init, 247K bss, 12280K reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xff000000 (1512 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x8069cba4 (6739 kB) .init : 0x8069d000 - 0x806f3c40 ( 348 kB) .data : 0x806f4000 - 0x80735650 ( 262 kB) .bss : 0x80735650 - 0x80773384 ( 248 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949ms Console: colour dummy device 80x30 Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok ftrace: allocating 17987 entries in 53 pages CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x804c16c8 - 0x804c1720 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated. CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 NET: Registered protocol family 16 fpga bridge driver DMA: preallocated 256 KiB pool for atomic coherent allocations L310 cache controller enabled l2x0: 8 ways, CACHE_ID 0x410030c9, AUX_CTRL 0x32460000, Cache size: 512 kB syscon ffd05000.rstmgr: regmap [mem 0xffd05000-0xffd05fff] registered syscon ffc25000.sdrctl: regmap [mem 0xffc25000-0xffc25fff] registered syscon ff800000.l3regs: regmap [mem 0xff800000-0xff800fff] registered syscon ffd08000.sysmgr: regmap [mem 0xffd08000-0xffd0bfff] registered hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. altera_hps2fpga_bridge fpgabridge.2: fpga bridge [hps2fpga] registered as device hps2fpga altera_hps2fpga_bridge fpgabridge.2: init-val not specified altera_hps2fpga_bridge fpgabridge.3: fpga bridge [lshps2fpga] registered as device lwhps2fpga altera_hps2fpga_bridge fpgabridge.3: init-val not specified altera_hps2fpga_bridge fpgabridge.4: fpga bridge [fpga2hps] registered as device fpga2hps altera_hps2fpga_bridge fpgabridge.4: init-val not specified bio: create slab at 0 FPGA Mangager framework driver vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Switched to clocksource timer1 NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available arm-pmu arm-pmu: PMU:CTI successfully enabled NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered NTFS driver 2.1.30 [Flags: R/W]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 1000 io scheduler noop registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A console [ttyS0] enabled ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0 brd: module loaded at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write cadence-qspi ff705000.spi: DMA NOT enabled cadence-qspi ff705000.spi: master is unqueued, this is deprecated m25p80 spi2.0: found n25q128a11, expected n25q00 m25p80 spi2.0: n25q128a11 (16384 Kbytes) 6 ofpart partitions found on MTD device spi2.0 Creating 6 MTD partitions on "spi2.0": 0x000000000000-0x000000040000 : "Preloader Image 0-3" 0x000000040000-0x000000050000 : "U-Boot Env" 0x000000050000-0x000000060000 : "DTB" 0x000000060000-0x0000000e0000 : "U-Boot" 0x0000000e0000-0x0000008e0000 : "Kernel" 0x0000008e0000-0x000001000000 : "Flash 0 jffs2 Filesystem" m25p80 spi2.1: found n25q128a11, expected n25q00 m25p80 spi2.1: n25q128a11 (16384 Kbytes) 1 ofpart partitions found on MTD device spi2.1 Creating 1 MTD partitions on "spi2.1": 0x000000000000-0x000001000000 : "Flash 1 Filesystem" cadence-qspi ff705000.spi: Cadence QSPI controller driver dw_spi_mmio fff00000.spi: master is unqueued, this is deprecated CAN device driver interface c_can_platform ffc00000.d_can: invalid resource c_can_platform ffc00000.d_can: control memory is not used for raminit c_can_platform ffc00000.d_can: c_can_platform device registered (regs=a08d0000, irq=163) c_can_platform ffc01000.d_can: invalid resource c_can_platform ffc01000.d_can: control memory is not used for raminit c_can_platform ffc01000.d_can: c_can_platform device registered (regs=a08d2000, irq=167) stmmac - user ID: 0x10, Synopsys ID: 0x37 Ring mode enabled DMA HW capability register supported Enhanced/Alternate descriptors Enabled extended descriptors RX Checksum Offload Engine supported (type 2) TX Checksum insertion supported Enable RX Mitigation via HW Watchdog Timer libphy: stmmac: probed eth0: PHY ID 00221622 at 3 IRQ 0 (stmmac-0:03) active usbcore: registered new interface driver usb-storage s3c-hsotg ffb40000.usb: unable to find phy s3c-hsotg ffb40000.usb: regs a08e0000, irq 160 s3c-hsotg ffb40000.usb: EPs:15 s3c-hsotg ffb40000.usb: dedicated fifos mousedev: PS/2 mouse device common for all mice rtc-ab18xx 0-0069: rtc core: registered ab1803 as rtc0 rtc-ab18xx 0-0069: 192 bytes nvram i2c /dev entries driver Synopsys Designware Multimedia Card Interface Driver dwmmc_socfpga ff704000.dwmmc0: Using internal DMA controller. dwmmc_socfpga ff704000.dwmmc0: Version ID is 240a dwmmc_socfpga ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo mmc_host mmc0: Bus speed (slot 0) = 12500000Hz (slot req 400000Hz, actual 390625HZ div = 16) dwmmc_socfpga ff704000.dwmmc0: 1 slots initialized lp5562 0-0030: internal clock used ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver oprofile: using arm/armv7-ca9 TCP: cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered ThumbEE CPU extension supported. Registering SWP/SWPB emulation handler Waiting for root device /dev/mmcblk0p2... dwmmc_socfpga ff704000.dwmmc0: data FIFO error (status=00000800) mmc0: problem reading SD Status register. mmc_host mmc0: Bus speed (slot 0) = 12500000Hz (slot req 12500000Hz, actual 12500000HZ div = 0) mmc0: new high speed SDHC card at address 8883 mmcblk0: mmc0:8883 RF04G 3.69 GiB mmcblk0: p1 p2 p3 kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 344K (8069d000 - 806f3000) INIT: version 2.88 booting Error opening /dev/fb0: No such file or directory Starting udev udevd[84]: starting version 182 Starting Bootlog daemon: bootlogd. Configuring network interfaces... eth0: device MAC address 70:00:d5:ef:98:3c udhcpc (v1.21.1) started Sending discover... libphy: stmmac-0:03 - Link is Up - 1000/Full Sending discover... Sending select for 10.40.20.200... Lease of 10.40.20.200 obtained, lease time 604800 /etc/udhcpc.d/50default: Adding DNS 10.40.16.1 /etc/udhcpc.d/50default: Adding DNS 10.40.16.4 done. Starting rpcbind daemon...rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 done. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 warning: /etc/sysctl.conf(70): invalid syntax, continuing... warning: /etc/sysctl.conf(71): invalid syntax, continuing... net.core.wmem_max = 12582912 net.core.rmem_max = 12582912 net.ipv4.tcp_rmem = 12582912 12582912 12582912 net.ipv4.tcp_wmem = 12582912 12582912 12582912 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_timestamps = 1 net.ipv4.tcp_sack = 1 net.ipv4.tcp_no_metrics_save = 1 net.core.netdev_max_backlog = 50000 net.ipv4.tcp_mtu_probing = 1 net.ipv4.tcp_slow_start_after_idle = 0 Starting atd: OK INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd generating ssh RSA key... generating ssh ECDSA key... generating ssh DSA key... done. creating NFS state directory: done NFS daemon support not enabled in kernel Starting system log daemon...0 Starting kernel log daemon...0 Starting Lighttpd Web Server: lighttpd. 2015-01-21 07:57:28: (/home/user/brdu/poky/build/tmp/work/cortexa9hf-vfp-neon-poky-linux-gnueabi/lighttpd/1.4.32-r0/lighttpd-1.4.32/src/log.c.118) opening errorlog '/www/logs/lighttpd.error.log' failed: Read-only file system Starting crond: OK Stopping Bootlog daemon: bootlogd. Poky (Yocto Project Reference Distro) 1.5.3 mitysom-5csx /dev/ttyS0 mitysom-5csx login: