U-Boot SPL 2013.01.01 (Apr 08 2015 - 15:41:35) BOARD : Critical Link MitySOM-5CSx Module CLOCK: EOSC1 clock 25000 KHz CLOCK: EOSC2 clock 25000 KHz CLOCK: F2S_SDR_REF clock 0 KHz CLOCK: F2S_PER_REF clock 0 KHz CLOCK: MPU clock 925 MHz CLOCK: DDR clock 400 MHz CLOCK: UART clock 100000 KHz CLOCK: MMC clock 50000 KHz CLOCK: QSPI clock 370000 KHz RESET: COLD INFO : Watchdog enabled SDRAM: Initializing MMR registers SDRAM: Calibrating PHY SEQ.C: Preparing to start memory calibration SEQ.C: CALIBRATION PASSED SDRAM: 1024 MiB SDRAM: Scrubbing 0x01000000 - 0x02000000 SDRAM: Scrubbing success with 25 ms SDRAM: Scrubbing 0x00000000 - 0x01000000 SDRAM: Scrubbing 0x02000000 - 0x40000000 SDRAM: ECC Enabled ALTERA DWMMC: 0 SDRAM: Scrubbing success with consuming additional 1505 ms U-Boot 2013.01.01 (Apr 08 2015 - 15:42:36) Critical Link MitySOM-5CSx CPU : Altera SOCFPGA Platform BOARD : Critical Link MitySOM-5CSx Module I2C: ready DRAM: 1 GiB MMC: ALTERA DWMMC: 0 In: serial Out: serial Err: serial Net: mii0 preboot reading MMC uBoot ENV data ** File not found /etc/uBootStatic.env ** ## Warning: Input data exceeds 1048576 bytes - truncated ## Info: input data size = 1048578 = 0x100002 ERROR: Environment import failed: errno = 12 at cmd_nvedit.c:1004/do_env_import() ** File not found /etc/uBoot.env ** ## Warning: Input data exceeds 1048576 bytes - truncated ## Info: input data size = 1048578 = 0x100002 ERROR: Environment import failed: errno = 12 at cmd_nvedit.c:1004/do_env_import() ...done Hit any key to stop autoboot: 0 gpio: pin 28 (bank/mask = 0/0x10000000) gpio: pin 28 (gpio 28) value is 0 gpio: pin 28 (bank/mask = 0/0x10000000) gpio: pin 28 (gpio 28) value is 1 gpio: pin 0 (bank/mask = 0/0x00000001) gpio: pin 0 (gpio 0) value is 1 gpio: pin 9 (bank/mask = 0/0x00000200) gpio: pin 9 (gpio 9) value is 0 gpio: pin 9 (bank/mask = 0/0x00000200) gpio: pin 9 (gpio 9) value is 1 7007184 bytes read in 390 ms (17.1 MiB/s) ## Starting application at 0x3FF78704 ... ## Application terminated, rc = 0x0 3663536 bytes read in 264 ms (13.2 MiB/s) 20209 bytes read in 56 ms (351.6 KiB/s) ## Booting kernel from Legacy Image at 00007fc0 ... Image Name: Linux-3.16.0-g1d15155 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3663472 Bytes = 3.5 MiB Load Address: 00008000 Entry Point: 00008000 ## Flattened Device Tree blob at 00000100 Booting using the fdt blob at 0x00000100 XIP Kernel Image ... OK OK Loading Device Tree to 03ff8000, end 03fffef0 ... OK Starting kernel ... Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Linux version 3.16.0-g1d15155 (user@MitySOM-Dev) (gcc version 4.8.1 (GCC) ) #1 SMP Thu Apr 2 10:24:03 BST 2015 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: MitySOM-5CSX Altera SOCFPGA Cyclone V Memory policy: Data cache writealloc PERCPU: Embedded 8 pages/cpu @9fbd5000 s11008 r8192 d13568 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait mem=512M PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 511736K/524288K available (5516K kernel code, 277K rwdata, 1540K rodata, 382K init, 125K bss, 12552K reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xffe00000 (2048 kB) vmalloc : 0xa0800000 - 0xff000000 (1512 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x806ec300 (7057 kB) .init : 0x806ed000 - 0x8074cb00 ( 383 kB) .data : 0x8074e000 - 0x807937e8 ( 278 kB) .bss : 0x807937e8 - 0x807b2e1c ( 126 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 L2C: platform modifies aux control register: 0x02060000 -> 0x32460000 L2C: platform provided aux values permit register corruption. L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001 sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949672950ns Console: colour dummy device 80x30 Calibrating delay loop... 1836.64 BogoMIPS (lpj=9183232) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok ftrace: allocating 18739 entries in 55 pages CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x4fa588 - 0x4fa5e0 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated. CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 NET: Registered protocol family 16 fpga bridge driver DMA: preallocated 256 KiB pool for atomic coherent allocations hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. altera_hps2fpga_bridge soc:fpgabridge@0: fpga bridge [hps2fpga] registered as device hps2fpga altera_hps2fpga_bridge soc:fpgabridge@0: init-val not specified altera_hps2fpga_bridge soc:fpgabridge@1: fpga bridge [lshps2fpga] registered as device lwhps2fpga altera_hps2fpga_bridge soc:fpgabridge@1: init-val not specified altera_hps2fpga_bridge soc:fpgabridge@2: fpga bridge [fpga2hps] registered as device fpga2hps altera_hps2fpga_bridge soc:fpgabridge@2: init-val not specified FPGA Mangager framework driver vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Switched to clocksource timer1 NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available arm-pmu arm-pmu: PMU:CTI successfully enabled for 2 cores futex hash table entries: 512 (order: 3, 32768 bytes) NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered ntfs: driver 2.1.30 [Flags: R/W]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 999 io scheduler noop registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled console [ttyS0] disabled ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A console [ttyS0] enabled ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0 brd: module loaded at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write CAN device driver interface /soc/ethernet@ff702000: could not get #reset-cells for /soc/rstmgr@ffd05000 stmmaceth ff702000.ethernet: no reset control found stmmac - user ID: 0x10, Synopsys ID: 0x37 Ring mode enabled DMA HW capability register supported Enhanced/Alternate descriptors Enabled extended descriptors RX Checksum Offload Engine supported (type 2) TX Checksum insertion supported Enable RX Mitigation via HW Watchdog Timer libphy: stmmac: probed eth0: No PHY found stmmac_pltfr_probe: main driver probe failed dwc2 ffb40000.usb: s3c_hsotg_corereset: reset failed, GRSTCTL=00000000 dwc2 ffb40000.usb: EPs: 0, shared fifos, 0 entries in SPRAM ------------[ cut here ]------------ WARNING: CPU: 1 PID: 1 at drivers/usb/dwc2/gadget.c:203 s3c_hsotg_init_fifo+0x1b8/0x1ec() insufficient fifo memory Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.16.0-g1d15155 #1 [<8001860c>] (unwind_backtrace) from [<80013260>] (show_stack+0x20/0x24) [<80013260>] (show_stack) from [<804f4ef4>] (dump_stack+0x8c/0x9c) [<804f4ef4>] (dump_stack) from [<800264fc>] (warn_slowpath_common+0x80/0x9c) [<800264fc>] (warn_slowpath_common) from [<80026558>] (warn_slowpath_fmt+0x40/0x48) [<80026558>] (warn_slowpath_fmt) from [<803a72dc>] (s3c_hsotg_init_fifo+0x1b8/0x1ec) [<803a72dc>] (s3c_hsotg_init_fifo) from [<803aa50c>] (dwc2_gadget_init+0x1ec/0x6a4) [<803aa50c>] (dwc2_gadget_init) from [<803aad5c>] (dwc2_driver_probe+0x100/0x174) [<803aad5c>] (dwc2_driver_probe) from [<8032432c>] (platform_drv_probe+0x28/0x58) [<8032432c>] (platform_drv_probe) from [<803224fc>] (really_probe+0x84/0x224) [<803224fc>] (really_probe) from [<803227a8>] (__driver_attach+0xa8/0xac) [<803227a8>] (__driver_attach) from [<803208b0>] (bus_for_each_dev+0x70/0xa4) [<803208b0>] (bus_for_each_dev) from [<80322080>] (driver_attach+0x2c/0x30) [<80322080>] (driver_attach) from [<80321cf8>] (bus_add_driver+0x15c/0x204) [<80321cf8>] (bus_add_driver) from [<80323018>] (driver_register+0x88/0x108) [<80323018>] (driver_register) from [<803242fc>] (__platform_driver_register+0x64/0x6c) [<803242fc>] (__platform_driver_register) from [<807183dc>] (dwc2_platform_driver_init+0x1c/0x20) [<807183dc>] (dwc2_platform_driver_init) from [<80008940>] (do_one_initcall+0x9c/0x1dc) [<80008940>] (do_one_initcall) from [<806edde4>] (kernel_init_freeable+0x1e0/0x280) [<806edde4>] (kernel_init_freeable) from [<804f0ce8>] (kernel_init+0x1c/0x100) [<804f0ce8>] (kernel_init) from [<8000ebf8>] (ret_from_fork+0x14/0x20) ---[ end trace 38a0734e9bd7cabb ]--- ------------[ cut here ]------------ WARNING: CPU: 1 PID: 1 at drivers/usb/dwc2/gadget.c:214 s3c_hsotg_init_fifo+0x1e4/0x1ec() insufficient fifo memory Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 3.16.0-g1d15155 #1 [<8001860c>] (unwind_backtrace) from [<80013260>] (show_stack+0x20/0x24) [<80013260>] (show_stack) from [<804f4ef4>] (dump_stack+0x8c/0x9c) [<804f4ef4>] (dump_stack) from [<800264fc>] (warn_slowpath_common+0x80/0x9c) [<800264fc>] (warn_slowpath_common) from [<80026558>] (warn_slowpath_fmt+0x40/0x48) [<80026558>] (warn_slowpath_fmt) from [<803a7308>] (s3c_hsotg_init_fifo+0x1e4/0x1ec) [<803a7308>] (s3c_hsotg_init_fifo) from [<803aa50c>] (dwc2_gadget_init+0x1ec/0x6a4) [<803aa50c>] (dwc2_gadget_init) from [<803aad5c>] (dwc2_driver_probe+0x100/0x174) [<803aad5c>] (dwc2_driver_probe) from [<8032432c>] (platform_drv_probe+0x28/0x58) [<8032432c>] (platform_drv_probe) from [<803224fc>] (really_probe+0x84/0x224) [<803224fc>] (really_probe) from [<803227a8>] (__driver_attach+0xa8/0xac) [<803227a8>] (__driver_attach) from [<803208b0>] (bus_for_each_dev+0x70/0xa4) [<803208b0>] (bus_for_each_dev) from [<80322080>] (driver_attach+0x2c/0x30) [<80322080>] (driver_attach) from [<80321cf8>] (bus_add_driver+0x15c/0x204) [<80321cf8>] (bus_add_driver) from [<80323018>] (driver_register+0x88/0x108) [<80323018>] (driver_register) from [<803242fc>] (__platform_driver_register+0x64/0x6c) [<803242fc>] (__platform_driver_register) from [<807183dc>] (dwc2_platform_driver_init+0x1c/0x20) [<807183dc>] (dwc2_platform_driver_init) from [<80008940>] (do_one_initcall+0x9c/0x1dc) [<80008940>] (do_one_initcall) from [<806edde4>] (kernel_init_freeable+0x1e0/0x280) [<806edde4>] (kernel_init_freeable) from [<804f0ce8>] (kernel_init+0x1c/0x100) [<804f0ce8>] (kernel_init) from [<8000ebf8>] (ret_from_fork+0x14/0x20) ---[ end trace 38a0734e9bd7cabc ]--- dwc2 ffb40000.usb: wrong number of EPs (zero) dwc2: probe of ffb40000.usb failed with error -22 usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice rtc-ab18xx 0-0069: rtc core: registered ab1803 as rtc0 rtc-ab18xx 0-0069: 192 bytes nvram i2c /dev entries driver i2c_designware ffc05000.i2c: controller timed out i2c_designware ffc05000.i2c: controller timed out i2c_designware ffc05000.i2c: controller timed out i2c_designware ffc05000.i2c: controller timed out i2c_designware ffc05000.i2c: controller timed out i2c_designware ffc05000.i2c: controller timed out Synopsys Designware Multimedia Card Interface Driver dw_mmc ff704000.dwmmc0: no vmmc regulator found: -19 dw_mmc ff704000.dwmmc0: Using internal DMA controller. dw_mmc ff704000.dwmmc0: Version ID is 240a dw_mmc ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo dw_mmc ff704000.dwmmc0: 1 slots initialized lp5562 0-0030: internal clock used ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver oprofile: using arm/armv7-ca9 TCP: cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered ThumbEE CPU extension supported. Registering SWP/SWPB emulation handler Waiting for root device /dev/mmcblk0p2... mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 50000000Hz, actual 50000000HZ div = 2) mmc0: new high speed SDHC card at address 1234 mmcblk0: mmc0:1234 SA04G 3.63 GiB mmcblk0: p1 p2 p3 kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 380K (806ed000 - 8074c000) INIT: version 2.88 booting Error opening /dev/fb0: No such file or directory Starting udev udevd[70]: starting version 182 input: gpio_keys as /devices/gpio_keys/input/input0 random: nonblocking pool is initialized Starting Bootlog daemon: bootlogd. Populating dev cache Configuring network interfaces... eth0: ERROR while getting interface flags: No such device Starting rpcbind daemon...NET: Registered protocol family 10 done. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 Fri Apr 10 09:34:00 UTC 2015 Starting atd: OK INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd generating ssh RSA key... generating ssh ECDSA key... generating ssh DSA key... done. creating NFS state directory: done NFS daemon support not enabled in kernel Starting system log daemon...0 Starting kernel log daemon...0 Starting Lighttpd Web Server: lighttpd. Starting crond: OK Starting Network Interface Plugging Daemon: eth0. Stopping Bootlog daemon: bootlogd. Poky (Yocto Project Reference Distro) 1.5.4 mitysom-5csx /dev/ttyS0 mitysom-5csx login: root root@mitysom-5csx:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@mitysom-5csx:~#