 
U-Boot SPL 2011.09 (Mar 18 2014 - 15:08:14)
Texas Instruments Revision detection unimplemented

 Sandia Pin Configuration is setting up 
 Sandia Pin config is complete.... 
Critical Link AM335X Dev Kit
PLL configuration complete
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img


U-Boot 2011.09 (Mar 18 2014 - 15:08:14)

I2C:   ready
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  HW ECC Hamming Code selected
256 MiB
MMC:   OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment

Net:   cpsw
Hit any key to stop autoboot:  3  2  1  0 
SD/MMC found on device 0
reading uenv.txt

1711 bytes read
Loaded environment from uenv.txt
Importing environment from mmc ...
reading uImage

3705872 bytes read
## Booting kernel from Legacy Image at 80007fc0 ...
   Image Name:   Linux-3.2.0-00217-g3c4aa5c-dirty
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3705808 Bytes = 3.5 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   XIP Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.2.0-00217-g3c4aa5c-dirty (root@dlinux) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #13 Tue Mar 18 15:13:44 PDT 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: mityarm335x
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] AM335X ES1.0 (sgx neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 251284k/251284k available, 10860k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0746000   (7416 kB)
[    0.000000]       .init : 0xc0746000 - 0xc0784000   ( 248 kB)
[    0.000000]       .data : 0xc0784000 - 0xc081d620   ( 614 kB)
[    0.000000]        .bss : 0xc081d644 - 0xc085d074   ( 255 kB)
[    0.000000] NR_IRQS:396
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[    0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000000] Console: colour dummy device 80x30
[    0.000152] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)
[    0.058044] pid_max: default: 32768 minimum: 301
[    0.058166] Security Framework initialized
[    0.058258] Mount-cache hash table entries: 512
[    0.058624] CPU: Testing write buffer coherency: ok
[    0.078338] omap_hwmod: gfx: failed to hardreset
[    0.094329] omap_hwmod: pruss: failed to hardreset
[    0.095672] print_constraints: dummy: 
[    0.096069] NET: Registered protocol family 16
[    0.098297] OMAP GPIO hardware version 0.1
[    0.100982] omap_mux_init: Add partition: #1: core, flags: 0
[    0.103515]  omap_i2c.3: alias fck already exists
[    0.103790]  omap_i2c.2: alias fck already exists
[    0.104492] Registering mcspi 1 [2]
[    0.104553]  omap2_mcspi.1: alias fck already exists
[    0.104766] Registering mcspi 2 [2]
[    0.104797]  omap2_mcspi.2: alias fck already exists
[    0.105072]  edma.0: alias fck already exists
[    0.105072]  edma.0: alias fck already exists
[    0.105102]  edma.0: alias fck already exists
[    0.108428] baseboard_init [MityARM-335x DevKit]...
[    0.108428] Configure Ethernet RGMII PINs...
[    0.108642] Configure SMSC LAN8820 PHY chip...
[    0.108642] ------------[ cut here ]------------
[    0.108673] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x58/0xd4()
[    0.108703] autorequest GPIO-53
[    0.108703] Modules linked in:
[    0.108703] Backtrace: 
[    0.108734] [<c00179e8>] (dump_backtrace+0x0/0x10c) from [<c04c35e4>] (dump_stack+0x18/0x1c)
[    0.108764]  r6:00000065 r5:c01eb61c r4:cf81bf00 r3:c07a6750
[    0.108795] [<c04c35cc>] (dump_stack+0x0/0x1c) from [<c004190c>] (warn_slowpath_common+0x54/0x6c)
[    0.108825] [<c00418b8>] (warn_slowpath_common+0x0/0x6c) from [<c00419c8>] (warn_slowpath_fmt+0x38/0x40)
[    0.108825]  r8:cf8044d8 r7:40000013 r6:00000035 r5:cf8044d8 r4:c084aabc
[    0.108856] r3:00000009
[    0.108856] [<c0041990>] (warn_slowpath_fmt+0x0/0x40) from [<c01eb61c>] (gpio_ensure_requested+0x58/0xd4)
[    0.108886]  r3:00000035 r2:c06b68dc
[    0.108886] [<c01eb5c4>] (gpio_ensure_requested+0x0/0xd4) from [<c01eb828>] (gpio_direction_output+0xa0/0x160)
[    0.108917]  r6:c084aabc r5:cf81a000 r4:00000015 r3:00000020
[    0.108947] [<c01eb788>] (gpio_direction_output+0x0/0x160) from [<c075377c>] (baseboard_init+0x74/0x464)
[    0.108947] [<c0753708>] (baseboard_init+0x0/0x464) from [<c00087bc>] (do_one_initcall+0x40/0x184)
[    0.108978]  r5:cf81a000 r4:c081d680
[    0.109008] [<c000877c>] (do_one_initcall+0x0/0x184) from [<c0746858>] (kernel_init+0x80/0x11c)
[    0.109008] [<c07467d8>] (kernel_init+0x0/0x11c) from [<c004474c>] (do_exit+0x0/0x66c)
[    0.109039]  r5:c07467d8 r4:00000000
[    0.109100] ---[ end trace 1b75b31a2719ed1c ]---
[    0.109313]  omap_hsmmc.0: alias fck already exists
[    0.109771]  omap_hsmmc.2: alias fck already exists
[    0.110748]  da8xx_lcdc.0: alias fck already exists
[    0.111267]  d_can.0: alias fck already exists
[    0.111511]  d_can.1: alias fck already exists
[    0.111785] Configuring audio...
[    0.111846] Registering mcasp[1]
[    0.111877]  davinci-mcasp.1: alias fck already exists
[    0.112487]  omap_i2c.1: alias fck already exists
[    0.112701] WLAN GPIO Info.. IRQ = 186 WL_EN = 100 BT_EN = -22
[    0.112731] Bluetooth not Enabled!
[    0.112792] baseboard_setup_wlan: finished
[    0.112854] ------------[ cut here ]------------
[    0.112884] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x58/0xd4()
[    0.112884] autorequest GPIO-54
[    0.112884] Modules linked in:
[    0.112915] Backtrace: 
[    0.112945] [<c00179e8>] (dump_backtrace+0x0/0x10c) from [<c04c35e4>] (dump_stack+0x18/0x1c)
[    0.112945]  r6:00000065 r5:c01eb61c r4:cf81bf00 r3:c07a6750
[    0.112976] [<c04c35cc>] (dump_stack+0x0/0x1c) from [<c004190c>] (warn_slowpath_common+0x54/0x6c)
[    0.113006] [<c00418b8>] (warn_slowpath_common+0x0/0x6c) from [<c00419c8>] (warn_slowpath_fmt+0x38/0x40)
[    0.113006]  r8:cf8044d8 r7:60000013 r6:00000036 r5:cf8044d8 r4:c084aac8
[    0.113037] r3:00000009
[    0.113037] [<c0041990>] (warn_slowpath_fmt+0x0/0x40) from [<c01eb61c>] (gpio_ensure_requested+0x58/0xd4)
[    0.113067]  r3:00000036 r2:c06b68dc
[    0.113067] [<c01eb5c4>] (gpio_ensure_requested+0x0/0xd4) from [<c01eb828>] (gpio_direction_output+0xa0/0x160)
[    0.113098]  r6:c084aac8 r5:c04ccb90 r4:00000016 r3:00000020
[    0.113128] [<c01eb788>] (gpio_direction_output+0x0/0x160) from [<c0753ab0>] (baseboard_init+0x3a8/0x464)
[    0.113159] [<c0753708>] (baseboard_init+0x0/0x464) from [<c00087bc>] (do_one_initcall+0x40/0x184)
[    0.113159]  r5:cf81a000 r4:c081d680
[    0.113189] [<c000877c>] (do_one_initcall+0x0/0x184) from [<c0746858>] (kernel_init+0x80/0x11c)
[    0.113220] [<c07467d8>] (kernel_init+0x0/0x11c) from [<c004474c>] (do_exit+0x0/0x66c)
[    0.113220]  r5:c07467d8 r4:00000000
[    0.113220] ---[ end trace 1b75b31a2719ed1d ]---
[    0.137725] bio: create slab <bio-0> at 0
[    0.139953] SCSI subsystem initialized
[    0.141998] usbcore: registered new interface driver usbfs
[    0.142333] usbcore: registered new interface driver hub
[    0.142547] usbcore: registered new device driver usb
[    0.142700] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3
[    0.143005] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0
[    0.156616] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[    0.157592] tps65910 3-002d: JTAGREVNUM 0x1
[    0.159973] print_constraints: VRTC: 
[    0.161437] print_constraints: VIO: at 1800 mV 
[    0.163696] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal 
[    0.165954] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal 
[    0.166961] print_constraints: VDD3: 5000 mV 
[    0.168395] print_constraints: VDIG1: at 1800 mV 
[    0.169799] print_constraints: VDIG2: at 1800 mV 
[    0.171234] print_constraints: VPLL: at 1800 mV 
[    0.172637] print_constraints: VDAC: at 1800 mV 
[    0.174072] print_constraints: VAUX1: at 1800 mV 
[    0.175506] print_constraints: VAUX2: at 3300 mV 
[    0.176910] print_constraints: VAUX33: at 3300 mV 
[    0.178344] print_constraints: VMMC: at 3300 mV 
[    0.178863] tps65910 3-002d: No interrupt support, no core IRQ
[    0.195983] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz
[    0.215667] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[    0.216827] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.218200] cfg80211: Calling CRDA to update world regulatory domain
[    0.219390] Switching to clocksource gp timer
[    0.235321] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    0.235534] musb-hdrc musb-hdrc.0: dma type: pio
[    0.236419] musb-hdrc musb-hdrc.0: USB OTG mode controller at d081c000 using PIO, IRQ 18
[    0.236602] musb-hdrc musb-hdrc.1: dma type: pio
[    0.236999] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[    0.237091] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
[    0.237213] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.237213] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.237243] usb usb1: Product: MUSB HDRC host driver
[    0.237243] usb usb1: Manufacturer: Linux 3.2.0-00217-g3c4aa5c-dirty musb-hcd
[    0.237274] usb usb1: SerialNumber: musb-hdrc.1
[    0.238037] hub 1-0:1.0: USB hub found
[    0.238067] hub 1-0:1.0: 1 port detected
[    0.238616] musb-hdrc musb-hdrc.1: USB OTG mode controller at d081e800 using PIO, IRQ 19
[    0.239074] NET: Registered protocol family 2
[    0.239288] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.239685] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.239837] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[    0.239929] TCP: Hash tables configured (established 8192 bind 8192)
[    0.239959] TCP reno registered
[    0.239959] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.239990] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.240173] NET: Registered protocol family 1
[    0.240447] RPC: Registered named UNIX socket transport module.
[    0.240478] RPC: Registered udp transport module.
[    0.240478] RPC: Registered tcp transport module.
[    0.240478] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.240692] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.252471] VFS: Disk quotas dquot_6.5.2
[    0.252532] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.253082] msgmni has been set to 490
[    0.253906] io scheduler noop registered
[    0.253936] io scheduler deadline registered
[    0.253997] io scheduler cfq registered (default)
[    0.254974] _regulator_get: tps6116x supply vlcd not found, using dummy regulator
[    0.257934] tps6116x tps6116x: registered backlight controller
[    0.258483] DA8XX FB - options = bpp=16
[    0.258605] da8xx_lcdc da8xx_lcdc.0: GLCD: Found 800x600 panel
[    0.259704] DA8XX FB: 1024 x 768 16 bpp
[    0.275451] Console: switching to colour frame buffer device 128x48
[    0.285736] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.287597] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[    1.316253] console [ttyO0] enabled
[    1.320709] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[    1.328430] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[    1.336181] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[    1.343902] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[    1.351593] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[    1.368988] brd: module loaded
[    1.377258] loop: module loaded
[    1.380737] i2c-core: driver [tsl2550] using legacy suspend method
[    1.387084] i2c-core: driver [tsl2550] using legacy resume method
[    1.393432] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
[    1.406097] MityARM-335x: Part Number = 3359-GX-226-RC
[    1.411376] MityARM-335x DevKit: factory_config_callback
[    1.417419] Configuring 256MB NAND device
[    1.422302] omap-gpmc omap-gpmc: GPMC revision 6.0
[    1.427246] Registering NAND on CS0
[    1.433746] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes)
[    1.439239] Creating 1 MTD partitions on "spi_flash":
[    1.444458] 0x000000000000-0x000000800000 : "NOR User Defined"
[    1.452545] omap2-nand driver initializing
[    1.457092] ONFI flash detected
[    1.460479] ONFI param page 0 valid
[    1.464050] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP)
[    1.472320] Creating 8 MTD partitions on "omap2-nand.0":
[    1.477783] 0x000000000000-0x000000020000 : "SPL"
[    1.484039] 0x000000020000-0x000000040000 : "SPL.backup1"
[    1.490936] 0x000000040000-0x000000060000 : "SPL.backup2"
[    1.497772] 0x000000060000-0x000000080000 : "SPL.backup3"
[    1.504669] 0x000000080000-0x000000260000 : "U-Boot"
[    1.511901] 0x000000260000-0x000000280000 : "U-Boot Env"
[    1.518707] 0x000000280000-0x000000780000 : "Kernel"
[    1.527221] 0x000000780000-0x000010000000 : "File System"
[    1.635620] OneNAND driver initializing
[    1.639862] INIT SMSC PHY.
[    1.643249] SMSC lan8820_driver status: 0
[    1.647613] CAN device driver interface
[    1.651580] CAN bus driver for Bosch D_CAN controller 1.0
[    1.657958] d_can d_can.0: device registered (irq=52, irq_obj=53)
[    1.664916] d_can d_can.1: device registered (irq=55, irq_obj=56)
[    1.720214] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[    1.726562] davinci_mdio davinci_mdio.0: detected phy mask fffffffe
[    1.733489] am335x_lan8820_phy_fixup 7c0ec here addr = 0
[    1.739288] davinci_mdio.0: probed
[    1.742828] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8820
[    1.751007] usbcore: registered new interface driver cdc_ether
[    1.757141] usbcore: registered new interface driver cdc_subset
[    1.763305] Initializing USB Mass Storage driver...
[    1.768585] usbcore: registered new interface driver usb-storage
[    1.774749] USB Mass Storage support registered.
[    1.779571]  gadget: using random self ethernet address
[    1.784973]  gadget: using random host ethernet address
[    1.790924] usb0: MAC 1a:3d:56:b7:98:d9
[    1.794860] usb0: HOST MAC 6a:0f:d5:2e:f9:f8
[    1.799316]  gadget: Ethernet Gadget, version: Memorial Day 2008
[    1.805541]  gadget: g_ether ready
[    1.809020] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[    1.814544] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2
[    1.822265] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.829223] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.836669] usb usb2: Product: MUSB HDRC host driver
[    1.841766] usb usb2: Manufacturer: Linux 3.2.0-00217-g3c4aa5c-dirty musb-hcd
[    1.849121] usb usb2: SerialNumber: musb-hdrc.0
[    1.854583] hub 2-0:1.0: USB hub found
[    1.858459] hub 2-0:1.0: 1 port detected
[    1.863708] mousedev: PS/2 mouse device common for all mice
[    1.870513] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
[    1.879577] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0
[    1.892608] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc1
[    1.900512] i2c /dev entries driver
[    1.905029] Linux media interface: v0.10
[    1.909271] Linux video capture interface: v2.00
[    1.914550] usbcore: registered new interface driver uvcvideo
[    1.920562] USB Video Class driver (1.1.1)
[    1.928863] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.937500] cpuidle: using governor ladder
[    1.942352] cpuidle: using governor menu
[    1.952941] usbcore: registered new interface driver usbhid
[    1.958770] usbhid: USB HID core driver
[    1.963806] usbcore: registered new interface driver snd-usb-audio
[    1.992736] tlv320aic26-codec spi1.1: Probing AIC26 SoC CODEC driver
[    2.011291] asoc: tlv320aic26-hifi <-> davinci-mcasp.1 mapping ok
[    2.018890] ALSA device list:
[    2.022033]   #0: MityARM-335X DevKit
[    2.025848] oprofile: hardware counters not available
[    2.031097] oprofile: using timer interrupt.
[    2.035583] nf_conntrack version 0.5.0 (3926 buckets, 15704 max)
[    2.042388] ip_tables: (C) 2000-2006 Netfilter Core Team
[    2.048065] TCP cubic registered
[    2.051452] NET: Registered protocol family 17
[    2.056121] can: controller area network core (rev 20090105 abi 8)
[    2.062652] NET: Registered protocol family 29
[    2.067352] can: raw protocol (rev 20090105)
[    2.071807] can: broadcast manager protocol (rev 20090105 t)
[    2.077758] lib80211: common routines for IEEE802.11 drivers
[    2.083709] Registering the dns_resolver key type
[    2.088684] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    2.096679] ThumbEE CPU extension supported.
[    2.101226] mux: Failed to setup hwmod io irq -22
[    2.106781] Power Management for AM33XX family
[    2.111694] Trying to load am335x-pm-firmware.bin (60 secs timeout)
[    2.118316] Copied the M3 firmware to UMEM
[    2.122650] omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift
[    2.137695] Detected MACID=78:c5:e5:77:ae:c6
[    2.143768] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801)
[    2.153045] Waiting for root device /dev/mmcblk0p2...
[    2.170532] mmc0: new high speed SDHC card at address aaaa
[    2.176940] mmcblk0: mmc0:aaaa SU16G 14.8 GiB 
[    2.183593]  mmcblk0: p1 p2 p3
[    2.474304] kjournald starting.  Commit interval 5 seconds
[    2.480102] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
[    2.491973] EXT3-fs (mmcblk0p2): using internal journal
[    2.497436] EXT3-fs (mmcblk0p2): recovery complete
[    2.504486] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    2.511749] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    2.518432] Freeing init memory: 248K

INIT: version 2.86 booting

Please wait: booting...
Starting udev
[    3.038696] udevd (820): /proc/820/oom_adj is deprecated, please use /proc/820/oom_score_adj instead.
[    7.796325] kjournald starting.  Commit interval 5 seconds
[    7.802154] EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended
[    7.852722] EXT3-fs (mmcblk0p3): using internal journal
[    7.858215] EXT3-fs (mmcblk0p3): recovery complete
[    7.863250] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode
[    7.988800] alignment: ignoring faults is unsafe on this CPU.  Defaulting to fixup mode.
Remounting root file system...
Caching udev devnodes
ALSA: Restoring mixer settings...
Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
eth0      No such device

ifconfig: SIOCGIFFLAGS: No such device
done.
Setting up IP spoofing protection: rp_filter.
Sat Dec 24 10:11:00 UTC 2011

INIT: Entering runlevel: 5

Starting system message bus: dbus.
Starting Hardware abstraction layer hald
Starting Dropbear SSH server: dropbear.
Starting telnet daemon.
Starting network benchmark server: netserver.
Starting syslogd/klogd: done
Starting thttpd.
Starting PVR
[   11.649353] pvrsrvkm: disagrees about version of symbol module_layout
insmod: error inserting '/lib/modules/3.1.0/kernel/drivers/gpu/pvr/pvrsrvkm.ko': -1 Invalid module format
FATAL: Module omaplfb not found.
FATAL: Module bufferclass_ti not found.
BusyBox v1.13.2 (2011-12-15 15:46:39 CST) multi-call binary

Usage: mknod [OPTIONS] NAME TYPE MAJOR MINOR

Create a special file (block, character, or pipe)

Options:
	-m	Create the special file using the specified mode (default a=rw)
TYPEs include:
	b:	Make a block device
	c or u:	Make a character device
	p:	Make a named pipe (MAJOR and MINOR are ignored)

chmod: /dev/pvrsrvkm: No such file or directory
[   11.752929] Unhandled fault: external abort on non-linefetch (0x1018) at 0x40262014
Bus error
Starting Lighttpd Web Server: lighttpd.
2011-12-24 10:11:01: (log.c.166) server started 
/
/
Starting Matrix GUI application.
FATAL: Module g_mass_storage not found.
***************************************************************
***************************************************************
NOTICE: This file system contains the followin GPLv3 packages:
	binutils-dev
	binutils-symlinks
	binutils
	gdbserver

If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution.  This can be done using
the opkg remove command.  i.e.:
    opkg remove <package>
Where <package> is the name printed in the list above

NOTE: If the package is a dependency of another package you
      will be notified of the dependent packages.  You should
      use the --force-removal-of-dependent-packages option to
      also remove the dependent packages as well
***************************************************************
***************************************************************

                                                                                                    
,--.   ,--.,--.  ,--.            ,---.  ,------. ,--.   ,--. 
|   `.'   |`--',-'  '-.,--. ,--./  O  \ |  .--. '|   `.'   |
|  |'.'|  |,--.'-.  .-' \  '  /|  .-.  ||  '--'.'|  |'.'|  |
|  |   |  ||  |  |  |    \   ' |  | |  ||  |\  \ |  |   | 
`--'   `--'`--'  `--'  .-'  /  `--' `--'`--' '--'`--'   `--' 
                       `---'                                
          ,----. ,----. ,-----.,--.   ,--. 
          '.-.  |'.-.  ||  .--' \  `.'  /  
            .' <   .' < '--. `\  .'    \   
          /'-'  |/'-'  |.--'  / /  .'.  \  
          `----' `----' `----' '--'   '--' 

Critical Link LLC http://support.criticallink.com mityarm-335x ttyO0
        Linux kernel verison Linux armv7l #13 Tue Mar 18 15:13:44 PDT 2014

mityarm-335x login: root
root@mityarm-335x:~# ifconfig -a
can0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          NOARP  MTU:16  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:10 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:52 

can1      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          NOARP  MTU:16  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:10 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:55 

eth1      Link encap:Ethernet  HWaddr 78:C5:E5:77:AE:C6  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:40 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:129 errors:0 dropped:0 overruns:0 frame:0
          TX packets:129 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:245629 (239.8 KiB)  TX bytes:245629 (239.8 KiB)

usb0      Link encap:Ethernet  HWaddr 1A:3D:56:B7:98:D9  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@mityarm-335x:~# ifconfig eth1 192.168.0.12
[   42.700012] am335x_lan8820_phy_fixup 7c0ec here addr = 0
[   42.705871] smsc_phy_config_init
[   42.709442] ..... smsc PHY REGS: 0: VAL: 2000 
[   42.714202] ..... smsc PHY REGS: 1: VAL: 794d 
[   42.718933] ..... smsc PHY REGS: 2: VAL: 7 
[   42.723419] ..... smsc PHY REGS: 3: VAL: c0ec 
[   42.728179] ..... smsc PHY REGS: 4: VAL: 1e1 
[   42.732788] ..... smsc PHY REGS: 5: VAL: c5e1 
[   42.737548] 
[   42.737548] CPSW phy found : id is : 0x7c0ec
[   42.744293] PHY 0:01 not found
root@mityarm-335x:~# [   43.731414] SMSC_config_aneg
[   45.731719] PHY: 0:00 - Link is Up - 100/Full
[   47.731811] PHY: 0:00 - Link is Up - 100/Half

root@mityarm-335x:~# ifcongi     config -a
can0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          NOARP  MTU:16  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:10 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:52 

can1      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          NOARP  MTU:16  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:10 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:55 

eth1      Link encap:Ethernet  HWaddr 78:C5:E5:77:AE:C6  
          inet addr:192.168.0.12  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:40 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:129 errors:0 dropped:0 overruns:0 frame:0
          TX packets:129 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:245629 (239.8 KiB)  TX bytes:245629 (239.8 KiB)

usb0      Link encap:Ethernet  HWaddr 1A:3D:56:B7:98:D9  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@mityarm-335x:~# ping 192.168.0.1
PING 192.168.0.1 (192.168.0.1): 56 data bytes

--- 192.168.0.1 ping statistics ---
6 packets transmitted, 0 packets received, 100% packet loss
root@mityarm-335x:~# ethtoll  ol eth1
Settings for eth1:
	Current message level: 0x00000000 (0)
			       
	Link detected: yes
root@mityarm-335x:~# 