
U-Boot SPL 2013.10 (Apr 27 2015 - 11:42:09)
MitySOM335x profile 1 - Model No: 3354-HX-X38-RI Serial No: 14008001
Configuring for 512 MB DDR3 @ 400MHz
enable_gpmc_cs_config: base = 8000000, size = 0, config1 = 800
Alstom NVSP2 -- NAND Page size = 4096k booting from dev 5
Using 4k bch16 layout
ECC Mode = 2 lo = 208/0
nand_spl_load_image: loading 4096 bytes from 100000 to 80800000
nand_spl_load_image: loading 455772 bytes from 100000 to 807fffc0


U-Boot 2013.10 (Apr 27 2015 - 11:42:09)

AM335X-GP rev 2
I2C:   ready
DRAM:  512 MiB
WARNING: Caches not enabled
enable_gpmc_cs_config: base = 8000000, size = 0, config1 = 800
NAND:  Using 4k bch16 layout
ECC Mode = 2 lo = 208/0
512 MiB
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
gpio input SPARE0 value = 0
Net:   cpsw:1 is connected to cpsw.  Reconnecting to cpsw
cpsw
Hit any key to stop autoboot:  0
SD/MMC found on device 0
reading uenv.txt
2199 bytes read in 5 ms (428.7 KiB/s)
Loaded environment from uenv.txt
Importing environment from mmc ...
Running uenvcmd ...
Setting bus to 1
i2c_write: error waiting for addr ACK (status=0x116)
Error writing the chip.
i2c_write: error waiting for addr ACK (status=0x116)
Error writing the chip.
reading uImage
3791312 bytes read in 397 ms (9.1 MiB/s)
## Booting kernel from Legacy Image at 80007fc0 ...
   Image Name:   Linux-3.2.0-svn158
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3791248 Bytes = 3.6 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   XIP Kernel Image ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Linux version 3.2.0-svn158 (mitydsp@mitydsp-dev) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #17 PREEMPT Mon Jan 12 15:28:44 EST 2015
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: mitysom335x
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] AM335X ES2.1 (sgx neon )
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 510864k/510864k available, 13424k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0787000   (7676 kB)
[    0.000000]       .init : 0xc0787000 - 0xc07c4000   ( 244 kB)
[    0.000000]       .data : 0xc07c4000 - 0xc085ced0   ( 612 kB)
[    0.000000]        .bss : 0xc085cef4 - 0xc08acb80   ( 320 kB)
[    0.000000] NR_IRQS:396
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[    0.000000] Total of 128 interrupts on 1 active controller
[    0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[    0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000000] Console: colour dummy device 80x30
[    0.000152] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    0.038848] pid_max: default: 32768 minimum: 301
[    0.039001] Security Framework initialized
[    0.039093] Mount-cache hash table entries: 512
[    0.039489] CPU: Testing write buffer coherency: ok
[    0.040466] devtmpfs: initialized
[    0.060211] omap_hwmod: gfx: failed to hardreset
[    0.075988] omap_hwmod: pruss: failed to hardreset
[    0.077484] print_constraints: dummy:
[    0.077972] NET: Registered protocol family 16
[    0.080718] OMAP GPIO hardware version 0.1
[    0.084075] mityarm335x_init...
[    0.084381] omap_mux_init: Add partition: #1: core, flags: 0
[    0.085723]  omap_i2c.3: alias fck already exists
[    0.086029]  omap_i2c.2: alias fck already exists
[    0.086853] Registering mcspi 1 [2]
[    0.086914]  omap2_mcspi.1: alias fck already exists
[    0.087158] Registering mcspi 2 [2]
[    0.087188]  omap2_mcspi.2: alias fck already exists
[    0.087524]  edma.0: alias fck already exists
[    0.087554]  edma.0: alias fck already exists
[    0.087554]  edma.0: alias fck already exists
[    0.091857] baseboard_init [Alstom NVSP2]...
[    0.092163] _omap_mux_get_by_name: Could not find signal gpmc_be1.gpmc_be1
[    0.093414]  omap_hsmmc.0: alias fck already exists
[    0.094116]  d_can.1: alias fck already exists
[    0.094818]  omap_i2c.1: alias fck already exists
[    0.127593] bio: create slab <bio-0> at 0
[    0.131225] SCSI subsystem initialized
[    0.133361] usbcore: registered new interface driver usbfs
[    0.133789] usbcore: registered new interface driver hub
[    0.134063] usbcore: registered new device driver usb
[    0.134246] musb-ti81xx musb-ti81xx: musb0, board_mode=0x3, plat_mode=0x3
[    0.134582] musb-ti81xx musb-ti81xx: musb1, board_mode=0x3, plat_mode=0x0
[    0.136108] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[    0.137145] tps65910 3-002d: JTAGREVNUM 0x1
[    0.142150] print_constraints: VRTC:
[    0.143707] print_constraints: VIO: at 1500 mV
[    0.146087] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal
[    0.148529] print_constraints: VDD2: 600 <--> 1500 mV at 1137 mV normal
[    0.149597] print_constraints: VDD3: 5000 mV
[    0.151092] print_constraints: VDIG1: at 1800 mV
[    0.152557] print_constraints: VDIG2: at 1800 mV
[    0.154052] print_constraints: VPLL: at 1800 mV
[    0.155517] print_constraints: VDAC: at 1800 mV
[    0.157043] print_constraints: VAUX1: at 1800 mV
[    0.158508] print_constraints: VAUX2: at 3300 mV
[    0.160003] print_constraints: VAUX33: at 3300 mV
[    0.161468] print_constraints: VMMC: at 3300 mV
[    0.162109] tps65910 3-002d: No interrupt support, no core IRQ
[    0.162322] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 100 kHz
[    0.178039] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[    0.179412] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.180267] Switching to clocksource gp timer
[    0.205108] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    0.205322] musb-hdrc musb-hdrc.0: dma type: dma-cppi41
[    0.206298] musb-hdrc musb-hdrc.0: USB OTG mode controller at e081c000 using PIO, IRQ 18
[    0.206542] musb-hdrc musb-hdrc.1: dma type: dma-cppi41
[    0.206970] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[    0.207061] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
[    0.207244] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.207244] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.207275] usb usb1: Product: MUSB HDRC host driver
[    0.207275] usb usb1: Manufacturer: Linux 3.2.0-svn158 musb-hcd
[    0.207275] usb usb1: SerialNumber: musb-hdrc.1
[    0.208312] hub 1-0:1.0: USB hub found
[    0.208374] hub 1-0:1.0: 1 port detected
[    0.209075] musb-hdrc musb-hdrc.1: USB OTG mode controller at e081e800 using PIO, IRQ 19
[    0.209808] NET: Registered protocol family 2
[    0.210083] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.210968] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.211242] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    0.211395] TCP: Hash tables configured (established 16384 bind 16384)
[    0.211425] TCP reno registered
[    0.211425] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.211456] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.211730] NET: Registered protocol family 1
[    0.212341] RPC: Registered named UNIX socket transport module.
[    0.212341] RPC: Registered udp transport module.
[    0.212371] RPC: Registered tcp transport module.
[    0.212371] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.212677] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.232147] VFS: Disk quotas dquot_6.5.2
[    0.232269] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.234710] msgmni has been set to 997
[    0.235931] io scheduler noop registered
[    0.235931] io scheduler deadline registered
[    0.236145] io scheduler cfq registered (default)
[    0.238433] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.241180] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[    0.918640] console [ttyO0] enabled
[    0.922943] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[    0.931274] zilog_escc_init returning with 0
[    0.953613] brd: module loaded
[    0.963623] loop: module loaded
[    0.967132] i2c-core: driver [tsl2550] using legacy suspend method
[    0.973724] i2c-core: driver [tsl2550] using legacy resume method
[    0.980133] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
[    0.992980] MitySOM-335x: Part Number = 3354-HX-X38-RI
[    0.998321] Alstom NVSP2: factory_config_callback
[    1.003814] No SPI NOR Flash found.
[    1.007446] Configuring 512MB NAND device
[    1.012359] omap-gpmc omap-gpmc: GPMC revision 6.0
[    1.017333] Registering NAND on CS0
[    1.021057] Enabling CS0, base=0x100000, size=0xf00000, config7=0xf40
[    1.027740] Registering CS0, resource start=0x100000, end=0xffffff
[    1.037628] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes)
[    1.043457] Creating 1 MTD partitions on "spi_flash":
[    1.048736] 0x000000000000-0x000000800000 : "NOR User Defined"
[    1.057312] omap2-nand driver initializing
[    1.062072] ONFI flash detected
[    1.065460] ONFI param page 0 valid
[    1.069091] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAWP)
[    1.077453] Creating 8 MTD partitions on "omap2-nand.0":
[    1.083007] 0x000000000000-0x000000040000 : "SPL"
[    1.089721] 0x000000040000-0x000000080000 : "SPL.backup1"
[    1.097137] 0x000000080000-0x0000000c0000 : "SPL.backup2"
[    1.104431] 0x0000000c0000-0x000000100000 : "SPL.backup3"
[    1.111846] 0x000000100000-0x000000300000 : "U-Boot"
[    1.119049] 0x000000300000-0x000000340000 : "U-Boot Env"
[    1.126342] 0x000000340000-0x000000840000 : "Kernel"
[    1.134246] 0x000000840000-0x000020000000 : "File System"
[    1.247436] OneNAND driver initializing
[    1.253967] CAN device driver interface
[    1.257965] CAN bus driver for Bosch D_CAN controller 1.0
[    1.264617] d_can d_can.1: device registered (irq=55, irq_obj=56)
[    1.320922] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[    1.327331] davinci_mdio davinci_mdio.0: detected phy mask fffffff9
[    1.334350] nvsp2_phy_fixup phy_id = 0x221622, addr = 1
[    1.340484] nvsp2_phy_fixup phy_id = 0x221622, addr = 2
[    1.346221] davinci_mdio.0: probed
[    1.349761] davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver Micrel KSZ9031 Gigabit PHY
[    1.358856] davinci_mdio davinci_mdio.0: phy[2]: device 0:02, driver Micrel KSZ9031 Gigabit PHY
[    1.368438] usbcore: registered new interface driver cdc_ether
[    1.374755] usbcore: registered new interface driver cdc_subset
[    1.381011] Initializing USB Mass Storage driver...
[    1.386322] usbcore: registered new interface driver usb-storage
[    1.392639] USB Mass Storage support registered.
[    1.398132] mousedev: PS/2 mouse device common for all mice
[    1.404663] dev addr = df8c6408
[    1.407928] pdev addr = df8c6400
[    1.414184] tps65910-rtc tps65910-rtc: Wake up is not possible as irq = 0
[    1.427459] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc0
[    1.435455] i2c /dev entries driver
[    1.440246] Linux media interface: v0.10
[    1.444641] Linux video capture interface: v2.00
[    1.449859] usbcore: registered new interface driver uvcvideo
[    1.455932] USB Video Class driver (1.1.1)
[    1.465301] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    1.474121] cpuidle: using governor ladder
[    1.479095] cpuidle: using governor menu
[    1.486511] usbcore: registered new interface driver usbhid
[    1.492462] usbhid: USB HID core driver
[    1.497253] usbcore: registered new interface driver snd-usb-audio
[    1.532562] ALSA device list:
[    1.535736]   No soundcards found.
[    1.539276] oprofile: hardware counters not available
[    1.544677] oprofile: using timer interrupt.
[    1.549163] nf_conntrack version 0.5.0 (7982 buckets, 31928 max)
[    1.556243] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.561981] TCP cubic registered
[    1.565399] NET: Registered protocol family 17
[    1.570068] can: controller area network core (rev 20090105 abi 8)
[    1.576751] NET: Registered protocol family 29
[    1.581512] can: raw protocol (rev 20090105)
[    1.585998] can: broadcast manager protocol (rev 20090105 t)
[    1.592041] lib80211: common routines for IEEE802.11 drivers
[    1.598052] Registering the dns_resolver key type
[    1.603088] Registering FPGA on CS1
[    1.606811] Enabling CS1, base=0x1000000, size=0x1000000, config7=0xf41
[    1.613739] Registering CS1, resource start=0x1000000, end=0x1ffffff
[    1.620910] fpga_base_probe constant1 = 0x89ab, constant2 = 0xcdef
[    1.627563] mmc0: new high speed SDHC card at address 59b4
[    1.736145] mmcblk0: mmc0:59b4 SDC   14.9 GiB
[    1.843322]  mmcblk0: p1 p2 p3
[    1.846710] zilog_escc: ttyZ0 at MMIO 0x1008004 (irq = 256) is a zs (ESCC)
[    1.855957] zilog_escc: ttyZ1 at MMIO 0x1008000 (irq = 256) is a zs (ESCC)
[    1.863952] slot_id_probe
[    1.866729] slot_id_probe - exit
[    1.870422] nvio_probe
[    1.872985] nvio_probe - exit
[    1.876342] i2c_eeprom_probe
[    1.879364] i2c_eeprom_probe - exit
[    1.883361] i2c_mbox_probe
[    1.886199] i2c_mbox_probe - exit
[    1.889953] vsp_probe
[    1.892395] vsp_probe - exit
[    1.895416] Registering ENET on CS2
[    1.899047] Enabling CS2, base=0x2000000, size=0x1000000, config7=0xf42
[    1.905975] Registering CS2, resource start=0x2000000, end=0x2ffffff
[    1.912963] ks8851_mll ks8851_mll: (unregistered net_device): message enable is 0
[    1.920806] ks8851_mll ks8851_mll: (unregistered net_device): the selftest passes
[    1.940338] ks8851_mll ks8851_mll: eth0: Using random mac address
[    1.946807] ks8851_mll ks8851_mll: eth0: Mac address is: 0e:d0:78:51:41:b6
[    1.954071] ks8851_mll ks8851_mll: eth0: Found chip, family: 0x88, id: 0x7, rev: 0x1
[    1.962188] ks8851_mll ks8851_mll: eth0: MARM register value: 0x7851
[    1.968841] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    1.976867] ThumbEE CPU extension supported.
[    1.981414] mux: Failed to setup hwmod io irq -22
[    1.987823] Power Management for AM33XX family
[    1.992706] Trying to load am335x-pm-firmware.bin (60 secs timeout)
[    1.999359] Copied the M3 firmware to UMEM
[    2.003662] omap_hwmod: wkup_m3: wkup_m3: hwmod data error: OMAP4 does not support st_shift
[    2.024047] Detected MACID=90:59:af:91:32:22
[    2.033233] tps65910-rtc tps65910-rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    2.283813] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended
[    2.293426] kjournald starting.  Commit interval 5 seconds
[    2.303192] EXT3-fs (mmcblk0p2): using internal journal
[    2.308654] EXT3-fs (mmcblk0p2): recovery complete
[    2.322814] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[    2.330078] VFS: Mounted root (ext3 filesystem) on device 179:2.
[    2.336730] Freeing init memory: 244K
INIT: version 2.86 booting
Please wait: booting...
Error opening /dev/fb0: No such device
Starting udev
[    2.836120] udevd (805): /proc/805/oom_adj is deprecated, please use /proc/805/oom_score_adj instead.
[    8.080780] EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended
[    8.090423] kjournald starting.  Commit interval 5 seconds
[    8.112243] EXT3-fs (mmcblk0p3): using internal journal
[    8.118041] EXT3-fs (mmcblk0p3): recovery complete
[    8.123413] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode
[   93.333190] alignment: ignoring faults is unsafe on this CPU.  Defaulting to fixup mode.
Remounting root file system...
Caching udev devnodes
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1625: No soundcards found...
Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCSIFADDR: No such device
route: SIOCADDRT: No such device
done.
Setting up IP spoofing protection: rp_filter.
Fri Dec 19 01:36:00 UTC 2014
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Hardware abstraction layer hald
Starting Dropbear SSH server: dropbear.
Starting telnet daemon.
Starting network benchmark server: netserver.
Starting syslogd/klogd: done
Starting thttpd.
Module pvrsrvkm failed to load. Retrying.
Running /sbin/depmod
Starting Lighttpd Web Server: lighttpd.
2014-12-19 01:36:01: (log.c.166) server started
/
/
Starting Matrix GUI application.
FATAL: Module g_mass_storage not found.
***************************************************************
***************************************************************
NOTICE: This file system contains the followin GPLv3 packages:
        binutils-dev
        binutils-symlinks
        binutils
        gdbserver

If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution.  This can be done using
the opkg remove command.  i.e.:
    opkg remove <package>
Where <package> is the name printed in the list above

NOTE: If t
                                                                                           
,--.   ,--.,--.  ,--.            ,---.   ,-----. ,--.   ,--.
|   `.'   |`--',-'  '-.,--. ,--.'   .-' '  .-.  '|   `.'   |
|  |'.'|  |,--.'-.  .-' \  '  / `.  `-. |  | |  ||  |'.'|  |
|  |   |  ||  |  |  |    \   '  .-'    |'  '-'  '|  |   |  |
`--'   `--'`--'  `--'  .-'  /   `-----'  `-----' `--'   `--'
                       `---'
              ,----. ,----. ,-----.,--.   ,--.
              '.-.  |'.-.  ||  .--' \  `.'  /
                .' <   .' < '--. `\  .'    \
              /'-'  |/'-'  |.--'  / /  .'.  \
              `----' `----' `----' '--'   '--'

Critical Link LLC http://support.criticallink.com mitysom-335x ttyO0
        Linux kernel verison Linux armv7l #17 PREEMPT Mon Jan 12 15:28:44 EST 2015

mitysom-335x login: