Project

General

Profile

RE: MityDSP L138F : The Linux kernel panics » Errors_out.txt

Terminal output - Okan Çalış, 09/06/2017 08:29 AM

 
1
U-Boot 2009.11-00006-g66bcd23-dirty (Dec 14 2011 - 11:33:14)
2

    
3
I2C:   ready
4
DRAM:  128 MB
5
NAND:  512 MiB
6
MMC:   davinci: 0
7
In:    serial
8
Out:   serial
9
Err:   serial
10
Error - Checksum on MityDSP-L138 Config Block Checksum Invalid
11
You must set the config to FLASH to make permanent
12
ARM    Clock : 300000000 Hz
13
DDR    Clock : 150000000 Hz
14
EMIFA  CLock : 100000000 Hz
15
DSP    Clock : 300000000 Hz
16
ASYNC3 Clock : 150000000 Hz
17
Enet  config : 2
18
MMC 0 Enable : 0
19
Resetting ethernet phy
20
Net:   Ethernet PHY: GENERIC @ 0x03 [0x8]
21

    
22
Hit any key to stop autoboot:  0
23
U-Boot > pri
24
bootdelay=3
25
baudrate=115200
26
bootfile="uImage"
27
flashuboot=tftp 0xc0700000 mityomap/u-boot-ubl.bin; sf probe 0; sf erase 0x10000 0x80000; sf write 0xc0700000 0x10000 ${filesize}
28
flashkernel=tftp 0xc0700000 mityomap/uImage; sf probe 0; sf erase 0x100000 0x280000; sf write 0xc0700000 0x100000 ${filesize}
29
flashubl=tftp 0xc0700000 mityomap/UBL_SPI_MEM.ais; sf probe 0; sf erase 0 0x10000; sf write 0xc0700000 0 0x10000
30
flashrootfs=tftp 0xc2000000 mityomap/mityomap-base-mityomapl138.jffs2; nand erase 0 0x08000000; nand write.jffs2 0xc2000000 0 ${filesize}
31
autoload=no
32
mtdids=nand0=nand
33
bootargsbase=mem=96M console=ttyS1,115200n8
34
flashargs=setenv bootargs ${bootargsbase} ${mtdparts} root=/dev/mtdblock0 rw,noatime rootfstype=jffs2
35
progfpga=nand device nand0; nand read c4000000 00c00000 00200000; nand read c4000000 00c00000 00200000;
36
updatefpga=tftp c0700000 mityomap/upp.bin; nand device nand0; nand erase c00000 200000; nand erase c00000 200000; nand write c0700000 c00000 200000
37
updatedsp=tftp c0700000 mityomap/binary.bin; nand device nand0; nand erase 200000 a00000; nand erase 200000 a00000; nand write c0700000 200000 a00000
38
updatedspbootloader=tftp c0700000 mityomap/dspBoot.out; nand erase 100000 100000; nand write c0700000 100000 100000;
39
mirketboot=run progfpga; nand read c0700000 00100000 00100000; nand read c7000000 00200000 00800000; nand read ca000000 20000 10000; nand read c2500000 30000 10000; loadfpga c4000000 200000;  bootdsp 0xc0700000;
40
bootargsbackup=mem=64M console=ttyS2,115200n8 ip=10.2.10.184 nfsroot=10.2.10.183: xport/rfs root=/dev/nfs rw
41
mtdparts=mtdparts=nand:14M(userfs),128M(rootfs),-(unused)
42
partition=nand0,0
43
mtddevnum=0
44
mtddevname=userfs
45
bootargs=mem=96M console=ttyS1,115200n8 root=/dev/mtdblock0 rw noatime rootfstype=jffs2 ip=192.168.1.11
46
filesize=269BB8
47
fileaddr=C0700000
48
ipaddr=192.168.1.11
49
serverip=192.168.1.10
50
defaultbootcmd=sf probe 0; sf read 0xc0700000 0x100000 0x300000; bootm 0xc0700000
51
bootcmd=sf probe 0; sf read 0xc0700000 0x100000 0x300000; bootm 0xc0700000
52
stdin=serial
53
stdout=serial
54
stderr=serial
55
ethaddr=70:b3:d5:b5:1d:93
56
ver=U-Boot 2009.11-00006-g66bcd23-dirty (Dec 14 2011 - 11:33:14)
57

    
58
Environment size: 2148/65532 bytes
59
U-Boot > boot
60
8192 KiB M25P64 at 0:0 is now current device
61
## Booting kernel from Legacy Image at c0700000 ...
62
   Image Name:   Linux-3.2.0
63
   Image Type:   ARM Linux Kernel Image (uncompressed)
64
   Data Size:    2530168 Bytes =  2.4 MB
65
   Load Address: c0008000
66
   Entry Point:  c0008000
67
   Verifying Checksum ... OK
68
   Loading Kernel Image ... OK
69
OK
70

    
71
Starting kernel ...
72

    
73
Uncompressing Linux... done, booting the kernel.
74
Linux version 3.2.0 (root@mitydsp) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #1 PREEMPT Mon Jan 13 11:06:16 EST 2014
75
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
76
CPU: VIVT data cache, VIVT instruction cache
77
Machine: MityDSP-L138/MityARM-1808
78
Ignoring unrecognised tag 0x42000101
79
Memory policy: ECC disabled, Data cache writethrough
80
DaVinci da850/omap-l138/am18x variant 0x1
81
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 24384
82
Kernel command line: mem=96M console=ttyS1,115200n8 root=/dev/mtdblock0 rw noatime rootfstype=jffs2 ip=192.168.1.11
83
PID hash table entries: 512 (order: -1, 2048 bytes)
84
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
85
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
86
Memory: 96MB = 96MB total
87
Memory: 91368k/91368k available, 6936k reserved, 0K highmem
88
Virtual kernel memory layout:
89
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
90
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
91
    vmalloc : 0xc6800000 - 0xfea00000   ( 898 MB)
92
    lowmem  : 0xc0000000 - 0xc6000000   (  96 MB)
93
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
94
      .text : 0xc0008000 - 0xc052c598   (5266 kB)
95
      .init : 0xc052d000 - 0xc0555000   ( 160 kB)
96
      .data : 0xc0556000 - 0xc05b5a80   ( 383 kB)
97
       .bss : 0xc05b5aa4 - 0xc05e2490   ( 179 kB)
98
NR_IRQS:245
99
Console: colour dummy device 80x30
100
Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
101
pid_max: default: 32768 minimum: 301
102
Mount-cache hash table entries: 512
103
CPU: Testing write buffer coherency: ok
104
devtmpfs: initialized
105
DaVinci: 144 gpio irqs
106
print_constraints: dummy:
107
NET: Registered protocol family 16
108
baseboard_pre_init: Entered
109
mityomapl138_setup_nand: using 8 bit data
110
baseboard_init [IndustrialIO]...
111
bio: create slab <bio-0> at 0
112
SCSI subsystem initialized
113
usbcore: registered new interface driver usbfs
114
usbcore: registered new interface driver hub
115
usbcore: registered new device driver usb
116
print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV
117
print_constraints: VDCDC2: 1800 mV
118
print_constraints: VDCDC3: 1200 mV
119
print_constraints: LDO1: 1800 mV
120
print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV
121
Advanced Linux Sound Architecture Driver Version 1.0.24.
122
Switching to clocksource timer0_1
123
musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
124
Waiting for USB PHY clock good...
125
musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using PIO, IRQ 58
126
NET: Registered protocol family 2
127
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
128
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
129
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
130
TCP: Hash tables configured (established 4096 bind 4096)
131
TCP reno registered
132
UDP hash table entries: 256 (order: 0, 4096 bytes)
133
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
134
NET: Registered protocol family 1
135
RPC: Registered named UNIX socket transport module.
136
RPC: Registered udp transport module.
137
RPC: Registered tcp transport module.
138
RPC: Registered tcp NFSv4.1 backchannel transport module.
139
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
140
msgmni has been set to 178
141
io scheduler noop registered (default)
142
start plist test
143
end plist test
144
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
145
serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A
146
serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A
147
console [ttyS1] enabled
148
serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A
149
brd: module loaded
150
at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
151
MityOMAPL138: Found MAC = 70:b3:d5:b5:1d:93
152
MityOMAPL138: Part Number = L138-FI-236-RL
153
ahci ahci: forcing PORTS_IMPL to 0x1
154
ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
155
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc
156
scsi0 : ahci_platform
157
ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67
158
ONFI flash detected
159
ONFI param page 0 valid
160
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP)
161
Bad block table found at page 262080, version 0x01
162
Bad block table found at page 262016, version 0x01
163
Creating 2 MTD partitions on "davinci_nand.1":
164
0x000000000000-0x000008000000 : "rootfs"
165
0x000008000000-0x000020000000 : "homefs"
166
davinci_nand davinci_nand.1: controller rev. 2.5
167
spi_davinci spi_davinci.1: DMA: supported
168
spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
169
m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes)
170
Creating 8 MTD partitions on "m25p80":
171
0x000000000000-0x000000010000 : "ubl"
172
0x000000010000-0x000000090000 : "u-boot"
173
0x000000090000-0x0000000a0000 : "u-boot-env"
174
0x0000000a0000-0x0000000b0000 : "periph-config"
175
Using LCD panel: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
176
baseboard_setup_lcd: unknown LCD type : ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
177
MII PHY configured
178
0x0000000b0000-0x000000100000 : "reserved"
179
0x000000100000-0x000000400000 : "kernel"
180
0x000000400000-0x000000600000 : "fpga"
181
0x000000600000-0x000000800000 : "spare"
182
spi_davinci spi_davinci.1: Controller at 0xfef0e000
183
CAN device driver interface
184
mcp251x spi1.1: probed
185
davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
186
davinci_mdio davinci_mdio.0: detected phy mask fffffff7
187
davinci_mdio.0: probed
188
davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown
189
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
190
ohci ohci.0: DA8xx OHCI
191
ohci ohci.0: new USB bus registered, assigned bus number 1
192
Waiting for USB PHY clock good...
193
ohci ohci.0: irq 59, io mem 0x01e25000
194
ata1: SATA link down (SStatus 0 SControl 300)
195
hub 1-0:1.0: USB hub found
196
hub 1-0:1.0: 1 port detected
197
Initializing USB Mass Storage driver...
198
usbcore: registered new interface driver usb-storage
199
USB Mass Storage support registered.
200
mousedev: PS/2 mouse device common for all mice
201
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
202
omap_rtc: RTC power up reset detected
203
omap_rtc: already running
204
i2c /dev entries driver
205
cpuidle: using governor ladder
206
cpuidle: using governor menu
207
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
208
usbcore: registered new interface driver usbhid
209
usbhid: USB HID core driver
210
dsd1791 spi1.2: Failed to add route LLOUT->Line Out
211
asoc: dsd1791 <-> davinci-mcasp.0 mapping ok
212
ALSA device list:
213
  #0: MityDSP-L138 INDIO
214
TCP cubic registered
215
NET: Registered protocol family 17
216
can: controller area network core (rev 20090105 abi 8)
217
NET: Registered protocol family 29
218
can: raw protocol (rev 20090105)
219
regulator_init_complete: LDO2: incomplete constraints, leaving on
220
regulator_init_complete: LDO1: incomplete constraints, leaving on
221
regulator_init_complete: VDCDC3: incomplete constraints, leaving on
222
regulator_init_complete: VDCDC2: incomplete constraints, leaving on
223
regulator_init_complete: VDCDC1: incomplete constraints, leaving on
224
console [netcon0] enabled
225
netconsole: network logging started
226
omap_rtc omap_rtc: setting system clock to 2000-01-01 00:55:04 UTC (946688104)
227
davinci_mdio davinci_mdio.0: resetting idled controller
228
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201)
229
PHY: 0:03 - Link is Up - 100/Full
230
IP-Config: Guessing netmask 255.255.255.0
231
IP-Config: Complete:
232
     device=eth0, addr=192.168.1.11, mask=255.255.255.0, gw=255.255.255.255,
233
     host=192.168.1.11, domain=, nis-domain=(none),
234
     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
235
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9d4: 0x48b1 instead
236
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9d8: 0xb238 instead
237
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9dc: 0xe34e instead
238
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9e0: 0xe80d instead
239
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9e4: 0xc3f5 instead
240
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9e8: 0xc02c instead
241
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9ec: 0x01e9 instead
242
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9f0: 0x64e4 instead
243
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9f4: 0x1012 instead
244
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0212d9f8: 0x01e2 instead
245
Further such events for this erase block will not be printed
246
VFS: Mounted root (jffs2 filesystem) on device 31:0.
247
devtmpfs: mounted
248
Freeing init memory: 160K
249
Failed to mount /sys/kernel/security: No such file or directory
250

    
251
Welcome to The Ångström Distribution!
252

    
253
NET: Registered protocol family 10
254
Starting Remount API VFS...
255
Starting Temporary Directory...
256
Starting Load Kernel Modules...
257
Started Set Up Additional Binary Formats                               [  OK  ]
258
Starting Apply Kernel Variables...
259
Starting Debug File System...
260
Started Huge Pages File System                                         [  OK  ]
261
Starting POSIX Message Queue File System...
262
Starting File System Check on Root Device...
263
Starting udev Coldplug all Devices...
264
Starting udev Kernel Device Manager...
265
Starting Journal Service...
266
Started Journal Service                                                [  OK  ]
267
Starting LSB: The RPC portmapper...
268
Started Remount API VFS                                                [  OK  ]
269
Started Temporary Directory                                            [  OK  ]
270
Started Load Kernel Modules                                            [  OK  ]
271
Started Apply Kernel Variables                                         [  OK  ]
272
Started Debug File System                                              [  OK  ]
273
Started POSIX Message Queue File System                                [  OK  ]
274
Started File System Check on Root Device                               [  OK  ]
275
Starting Remount Root FS...
276
Started Configuration File System                                      [  OK  ]
277
Started FUSE Control File System                                       [  OK  ]
278
udevd[1086]: starting version 182
279
Started udev Kernel Device Manager                                     [  OK  ]
280
Started Remount Root FS                                                [  OK  ]
281
Started Run pending postinsts                                          [  OK  ]
282
Started Machine ID first boot configure                                [  OK  ]
283
Starting Recreate Volatile Files and Directories...
284
Starting Load Random Seed...
285
Started Load Random Seed                                               [  OK  ]
286
Started Recreate Volatile Files and Directories                        [  OK  ]
287
Started LSB: The RPC portmapper                                        [  OK  ]
288
portmap[1095]: Starting portmap daemon...
289
Starting Avahi mDNS/DNS-SD Stack...
290
Started SSH Key Generation                                             [  OK  ]
291
Starting D-Bus System Message Bus...
292
Starting Permit User Sessions...
293
Starting Login Service...
294
Starting Timestamping service...
295
Started Timestamping service                                           [  OK  ]
296
Started Permit User Sessions                                           [  OK  ]
297
Started D-Bus System Message Bus                                       [  OK  ]
298
Starting Serial Getty on ttyS1...
299
Started Serial Getty on ttyS1                                          [  OK  ]
300

    
301
.---O---.
302
|       |                  .-.           o o
303
|   |   |-----.-----.-----.| |   .----..-----.-----.
304
|       |     | __  |  ---'| '--.|  .-'|     |     |
305
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
306
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
307
                -'  |
308
                '---'
309

    
310
The Angstrom Distribution mityomapl138 ttyS1
311

    
312
Angstrom v2012.05 - Kernel 3.2.0
313

    
314
mityomapl138 login: Started udev Coldplug all Devices                                      [  OK  ]
315
Starting Networking...
316
Started Avahi mDNS/DNS-SD Stack                                        [  OK  ]
317
Started Login Service                                                  [  OK  ]
318
Started Networking                                                     [  OK  ]
319
Starting Getty on tty1...
320
Started Getty on tty1                                                  [  OK  ]
321
root
322
Last login: Sat Jan  1 00:54:23 UTC 2000 on ttyS1
323
root@mityomapl138:~# shutdown now
324
Stopping Avahi mDNS/DNS-SD Stack...
325
Stopping D-Bus System Message Bus...
326
Stopping Serial Getty on tStopping Getty on tty1...                             
327
Stopping Login Service...
328
Stopping Timestamping service...
329
Starting Save Random Seed...
330
Stopped Avahi mDNS/DNS-SD Stack                                        [  OK  ]
331
Stopped Login Service                                                  [  OK  ]
332
Stopped D-Bus System Message Bus                                       [  OK  ]
333
Stopped Serial Getty on ttyS1                                          [  OK  ]
334
Stopped Getty on tty1                                                  [  OK  ]
335
Started Save Random Seed                                               [  OK  ]
336
Stopping Permit User Sessions...
337
Stopped Timestamping service                                           [  OK  ]
338
Stopped Permit User Sessions                                           [  OK  ]
339
Stopping Load Kernel Modules...
340
Stopped Load Kernel Modules                                            [  OK  ]
341
Stopping Apply Kernel Variables...
342
Stopped Apply Kernel Variables                                         [  OK  ]
343
Starting Notify Audit System and Update UTMP about System Shutdown...
344
Stopping Remount API VFS...
345
Stopped Remount API VFS                                                [  OK  ]
346
Stopping Temporary Directory...
347
Stopping Remount Root FS...
348
Stopped Remount Root FS                                                [  OK  ]
349
Sending SIGTERM to remaining processes...
350
Sending SIGKILL to remaining processes...
351
Unmounting file systems.
352
Unmounted /sys/kernel/debug.
353
Unmounted /dev/mqueue.
354
Disabling swaps.
355
Detaching loop devices.
356
Detaching DM devices.
357
USB 1.1 clocked from USB 2.0 PHY -- can't power it down
358
System halted.
    (1-1/1)
    Go to top
    Add picture from clipboard (Maximum size: 1 GB)