Jonathan Cormier's activity
From 01/21/2018 to 02/19/2018
02/07/2018
- 02:17 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- > U-Boot > print ver
> ver=U-Boot 2017.05-rc1-00044-gc3b7cfe-dirty (Apr 08 2017 - 20:35:07 +0300)
This is definitel... - 02:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Currently our application program is part of .jffs2 file system (Linux root file system + ap...
02/06/2018
- 03:08 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- Okan Çalış wrote:
> But this is our custom board. What should I enter in those fields?
This is the factory config... - 02:38 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- > MityOMAPL138: Read Factory Config Failed: -110
This line is very concerning. It appears you have erased or corrup...
02/05/2018
- 04:31 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Using McASP Rx clock generation module
- Ideally you should get it working from the baseboard as that should be the source of all the pinmux settings. Not su...
- 02:40 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- Your u-boot and kernel partitions don't seem to match. Also asuming the u-boot partitions scheme is the correct one, ...
02/02/2018
- 06:57 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Using McASP Rx clock generation module
- Can you dump the pinmux registers so we can double check them?
0x01C14120 - PINMUX0
0x01C14124 - PINMUX1
01/30/2018
- 07:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
>
> 1)When application runs,there is some debug part (as above)which dsp sends to arm with ds... - 03:16 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> > > 2) FPGA write in SPI Flash
> > > U-Boot > setenv bootcmd "run programfpga"
> > You appe...
01/29/2018
- 04:44 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> I followed the suggestions and tried to boot from flash. But It still does not run applicatio...
01/24/2018
- 07:47 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Jonathan Cormier wrote:
> > Vivek Ponnani wrote:
> > > Thanks for your response. It is very... - 03:59 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Thanks for your response. It is very helpful.
>
> Most of the points are cleared. I have f...
01/23/2018
- 02:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Hi,
>
> I have a custom board with
> -- MityDspl-138F module (with FPGA)
> -- No Ethern...
Also available in: Atom
Go to top