Project

General

Profile

RE: FPGA programming problems » New boot wrong.txt

Dario Russo, 05/25/2020 08:14 AM

 
1

    
2
U-Boot SPL 2013.01.01 (Feb 13 2020 - 07:29:59)
3
BOARD : Critical Link MitySOM-5CSx Module
4
CLOCK: EOSC1 clock 25000 KHz
5
CLOCK: EOSC2 clock 25000 KHz
6
CLOCK: F2S_SDR_REF clock 0 KHz
7
CLOCK: F2S_PER_REF clock 0 KHz
8
CLOCK: MPU clock 800 MHz
9
CLOCK: DDR clock 400 MHz
10
CLOCK: UART clock 100000 KHz
11
CLOCK: MMC clock 50000 KHz
12
CLOCK: QSPI clock 400000 KHz
13
RESET: WARM
14
INFO : Watchdog enabled
15
SDRAM: Initializing MMR registers
16
SDRAM: Calibrating PHY
17
SEQ.C: Preparing to start memory calibration
18
SEQ.C: CALIBRATION PASSED
19
SDRAM: 1024 MiB
20
SDRAM: Initializing SDRAM ECC
21
SDRAM: ECC initialized successfully with 1510 ms
22
SDRAM: ECC Enabled
23
ALTERA DWMMC: 0
24

    
25

    
26
U-Boot 2013.01.01 (May 21 2020 - 03:48:22) Critical Link MitySOM-5CSx
27

    
28
CPU   : Altera SOCFPGA Platform
29
BOARD : Critical Link MitySOM-5CSx Module
30
I2C:   ready
31
DRAM:  1 GiB
32
MMC:   ALTERA DWMMC: 0
33
In:    serial
34
Out:   serial
35
Err:   serial
36
Info - Didn't find block
37
Net:   mii0
38
gpio: pin 28 (bank/mask = 0/0x10000000)
39
gpio: pin 28 (gpio 28) value is 0
40
gpio: pin 28 (bank/mask = 0/0x10000000)
41
gpio: pin 28 (gpio 28) value is 1
42
gpio: pin 0 (bank/mask = 0/0x00000001)
43
gpio: pin 0 (gpio 0) value is 1
44
gpio: pin 9 (bank/mask = 0/0x00000200)
45
gpio: pin 9 (gpio 9) value is 0
46
gpio: pin 9 (bank/mask = 0/0x00000200)
47
gpio: pin 9 (gpio 9) value is 1
48
Hit any key to stop autoboot:  0
49
3702832 bytes read in 204 ms (17.3 MiB/s)
50
21708 bytes read in 26 ms (814.5 KiB/s)
51
7007204 bytes read in 379 ms (17.6 MiB/s)
52
## Starting application at 0x3FF755C4 ...
53
## Application terminated, rc = 0x0
54
## Starting application at 0x3FF755C4 ...
55
## Application terminated, rc = 0x0
56
## Booting kernel from Legacy Image at 00007fc0 ...
57
   Image Name:   Linux-3.16.0-g3a017ba
58
   Created:      2020-02-13  11:38:31 UTC
59
   Image Type:   ARM Linux Kernel Image (uncompressed)
60
   Data Size:    3702768 Bytes = 3.5 MiB
61
   Load Address: 00008000
62
   Entry Point:  00008000
63
## Flattened Device Tree blob at 00000100
64
   Booting using the fdt blob at 0x00000100
65
   XIP Kernel Image ... OK
66
OK
67
   Loading Device Tree to 03ff7000, end 03fff4cb ... OK
68

    
69
Starting kernel ...
70

    
71
Booting Linux on physical CPU 0x0
72
Initializing cgroup subsys cpuset
73
Linux version 3.16.0-g3a017ba (root@MitySOM-Dev) (gcc version 4.8.3 20140401 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.04 - Linaro GCC 4.8-2014.04) ) #2 SMP Thu Feb 13 06:38:14 EST 2020
74
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
75
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
76
Machine model: MitySOM-5CSX Altera SOCFPGA Cyclone V
77
Memory policy: Data cache writealloc
78
PERCPU: Embedded 8 pages/cpu @a7ad0000 s11008 r8192 d13568 u32768
79
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 162560
80
Kernel command line: console=ttyS0,115200 mem=640M root=/dev/mmcblk0p2 rw rootwait
81
PID hash table entries: 4096 (order: 2, 16384 bytes)
82
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
83
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
84
Memory: 641296K/655360K available (5540K kernel code, 280K rwdata, 1552K rodata, 394K init, 143K bss, 14064K reserved, 0K highmem)
85
Virtual kernel memory layout:
86
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
87
    fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
88
    vmalloc : 0xa8800000 - 0xff000000   (1384 MB)
89
    lowmem  : 0x80000000 - 0xa8000000   ( 640 MB)
90
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
91
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
92
      .text : 0x80008000 - 0x806f5318   (7093 kB)
93
      .init : 0x806f6000 - 0x80758b00   ( 395 kB)
94
      .data : 0x8075a000 - 0x807a0248   ( 281 kB)
95
       .bss : 0x807a0248 - 0x807c415c   ( 144 kB)
96
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
97
Hierarchical RCU implementation.
98
NR_IRQS:16 nr_irqs:16 16
99
L2C: platform modifies aux control register: 0x02060000 -> 0x32460000
100
L2C: platform provided aux values permit register corruption.
101
L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000
102
L2C-310 erratum 769419 enabled
103
L2C-310 enabling early BRESP for Cortex-A9
104
L2C-310 full line of zeros enabled for Cortex-A9
105
L2C-310 ID prefetch enabled, offset 1 lines
106
L2C-310 dynamic clock gating enabled, standby mode enabled
107
L2C-310 cache controller enabled, 8 ways, 512 kB
108
L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001
109
sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949672950ns
110
Console: colour dummy device 80x30
111
Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
112
pid_max: default: 32768 minimum: 301
113
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
114
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
115
CPU: Testing write buffer coherency: ok
116
ftrace: allocating 18906 entries in 56 pages
117
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
118
Setting up static identity map for 0x4ffba0 - 0x4ffbf8
119
CPU1: Booted secondary processor
120
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
121
Brought up 2 CPUs
122
SMP: Total of 2 processors activated.
123
CPU: All CPU(s) started in SVC mode.
124
devtmpfs: initialized
125
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
126
NET: Registered protocol family 16
127
fpga bridge driver
128
DMA: preallocated 256 KiB pool for atomic coherent allocations
129
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
130
hw-breakpoint: maximum watchpoint size is 4 bytes.
131
altera_hps2fpga_bridge soc:fpgabridge@0: fpga bridge [hps2fpga] registered as device hps2fpga
132
altera_hps2fpga_bridge soc:fpgabridge@0: init-val not specified
133
altera_hps2fpga_bridge soc:fpgabridge@1: fpga bridge [lwhps2fpga] registered as device lwhps2fpga
134
altera_hps2fpga_bridge soc:fpgabridge@1: init-val not specified
135
altera_hps2fpga_bridge soc:fpgabridge@2: fpga bridge [fpga2hps] registered as device fpga2hps
136
altera_hps2fpga_bridge soc:fpgabridge@2: init-val not specified
137
FPGA Mangager framework driver
138
vgaarb: loaded
139
SCSI subsystem initialized
140
usbcore: registered new interface driver usbfs
141
usbcore: registered new interface driver hub
142
usbcore: registered new device driver usb
143
pps_core: LinuxPPS API ver. 1 registered
144
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
145
PTP clock support registered
146
Switched to clocksource timer1
147
NET: Registered protocol family 2
148
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
149
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
150
TCP: Hash tables configured (established 8192 bind 8192)
151
TCP: reno registered
152
UDP hash table entries: 512 (order: 2, 16384 bytes)
153
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
154
NET: Registered protocol family 1
155
RPC: Registered named UNIX socket transport module.
156
RPC: Registered udp transport module.
157
RPC: Registered tcp transport module.
158
RPC: Registered tcp NFSv4.1 backchannel transport module.
159
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
160
arm-pmu arm-pmu: PMU:CTI successfully enabled for 2 cores
161
futex hash table entries: 512 (order: 3, 32768 bytes)
162
NFS: Registering the id_resolver key type
163
Key type id_resolver registered
164
Key type id_legacy registered
165
ntfs: driver 2.1.30 [Flags: R/W].
166
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
167
msgmni has been set to 1252
168
io scheduler noop registered (default)
169
dma-pl330 ffe01000.pdma: Loaded driver for PL330 DMAC-3412784
170
dma-pl330 ffe01000.pdma:        DBUFF-512x8bytes Num_Chans-8 Num_Peri-32 Num_Events-8
171
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
172
console [ttyS0] disabled
173
ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A
174
console [ttyS0] enabled
175
ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A
176
altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
177
brd: module loaded
178
at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write
179
cadence-qspi ff705000.spi: DMA NOT enabled
180
cadence-qspi ff705000.spi: master is unqueued, this is deprecated
181
m25p80 spi2.0: n25q128a11 (16384 Kbytes)
182
6 ofpart partitions found on MTD device spi2.0
183
Creating 6 MTD partitions on "spi2.0":
184
0x000000000000-0x000000040000 : "Preloader Image 0-3"
185
0x000000040000-0x000000050000 : "U-Boot Env"
186
0x000000050000-0x000000060000 : "DTB"
187
0x000000060000-0x0000000e0000 : "U-Boot"
188
0x0000000e0000-0x0000008e0000 : "Kernel"
189
0x0000008e0000-0x000001000000 : "FPGA"
190
m25p80 spi2.1: n25q128a11 (16384 Kbytes)
191
1 ofpart partitions found on MTD device spi2.1
192
Creating 1 MTD partitions on "spi2.1":
193
0x000000000000-0x000001000000 : "Data"
194
cadence-qspi ff705000.spi: Cadence QSPI controller driver
195
CAN device driver interface
196
c_can_platform ffc00000.can: c_can_platform device registered (regs=a88dc000, irq=163)
197
c_can_platform ffc01000.can: c_can_platform device registered (regs=a88de000, irq=167)
198
stmmac - user ID: 0x10, Synopsys ID: 0x37
199
 Ring mode enabled
200
 DMA HW capability register supported
201
 Enhanced/Alternate descriptors
202
        Enabled extended descriptors
203
 RX Checksum Offload Engine supported (type 2)
204
 TX Checksum insertion supported
205
 Enable RX Mitigation via HW Watchdog Timer
206
stmmac-mdio ff702000.mdio: mdio@ff702000
207
libphy: stmmac_mdio: probed
208
dwc2 ffb40000.usb: EPs: 15, dedicated fifos, 8064 entries in SPRAM
209
dwc2 ffb40000.usb: DWC OTG Controller
210
dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1
211
dwc2 ffb40000.usb: irq 160, io mem 0x00000000
212
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
213
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
214
usb usb1: Product: DWC OTG Controller
215
usb usb1: Manufacturer: Linux 3.16.0-g3a017ba dwc2_hsotg
216
usb usb1: SerialNumber: ffb40000.usb
217
hub 1-0:1.0: USB hub found
218
hub 1-0:1.0: 1 port detected
219
usbcore: registered new interface driver usb-storage
220
mousedev: PS/2 mouse device common for all mice
221
rtc-abx80x 0-0069: model 1805, revision 2.3, lot 2d, wafer 1, uid 4a89
222
rtc-abx80x 0-0069: rtc core: registered abx8xx as rtc0
223
i2c /dev entries driver
224
lm73 0-004c: sensor 'lm73'
225
Synopsys Designware Multimedia Card Interface Driver
226
dw_mmc ff704000.dwmmc0: no vmmc regulator found: -19
227
dw_mmc ff704000.dwmmc0: Using internal DMA controller.
228
dw_mmc ff704000.dwmmc0: Version ID is 240a
229
dw_mmc ff704000.dwmmc0: DW MMC controller at irq 171, 32 bit host data width, 1024 deep fifo
230
dw_mmc ff704000.dwmmc0: 1 slots initialized
231
lp5562 0-0030: internal clock used
232
ledtrig-cpu: registered to indicate activity on CPUs
233
usbcore: registered new interface driver usbhid
234
usbhid: USB HID core driver
235
oprofile: using arm/armv7-ca9
236
TCP: cubic registered
237
NET: Registered protocol family 17
238
NET: Registered protocol family 15
239
can: controller area network core (rev 20120528 abi 9)
240
NET: Registered protocol family 29
241
can: raw protocol (rev 20120528)
242
can: broadcast manager protocol (rev 20120528 t)
243
can: netlink gateway (rev 20130117) max_hops=1
244
8021q: 802.1Q VLAN Support v1.8
245
Key type dns_resolver registered
246
ThumbEE CPU extension supported.
247
Registering SWP/SWPB emulation handler
248
input: soc:gpio_keys as /devices/soc/soc:gpio_keys/input/input0
249
Waiting for root device /dev/mmcblk0p2...
250
mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 50000000Hz, actual 50000000HZ div = 2)
251
mmc0: new high speed SDHC card at address aaaa
252
mmcblk0: mmc0:aaaa SA08G 7.40 GiB
253
 mmcblk0: p1 p2 p3
254
kjournald starting.  Commit interval 5 seconds
255
EXT3-fs (mmcblk0p2): warning: mounting fs with errors, running e2fsck is recommended
256
EXT3-fs (mmcblk0p2): using internal journal
257
EXT3-fs (mmcblk0p2): recovery complete
258
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
259
VFS: Mounted root (ext3 filesystem) on device 179:2.
260
devtmpfs: mounted
261
Freeing unused kernel memory: 392K (806f6000 - 80758000)
262
INIT: version 2.88 booting
263
Error opening /dev/fb0: No such file or directory
264
Starting udev
265
random: nonblocking pool is initialized
266
udevd[87]: starting version 182
267
Starting Bootlog daemon: bootlogd.
268
Configuring network interfaces... udhcpc (v1.21.1) started
269
run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1
270
Sending discover...
271
stmmaceth ff702000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
272
Sending discover...
273
Sending select for 192.168.1.139...
274
Lease of 192.168.1.139 obtained, lease time 86400
275
run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1
276
/etc/udhcpc.d/50default: Adding DNS 192.168.1.254
277
done.
278
Starting rpcbind daemon...rpcbind: cannot create socket for udp6
279
rpcbind: cannot create socket for tcp6
280
done.
281
net.ipv4.conf.default.rp_filter = 1
282
net.ipv4.conf.all.rp_filter = 1
283
Starting atd: OK
284
INIT: Entering runlevel: 5
285
Starting system message bus: dbus.
286
Starting OpenBSD Secure Shell server: sshd
287
done.
288
creating NFS state directory: done
289
NFS daemon support not enabled in kernel
290
Starting system log daemon...0
291
Starting kernel log daemon...0
292
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon                       [ ok ]
293
 * Starting Avahi Unicast DNS Configuration Daemon: avahi-dnsconfd       [ ok ]
294
Starting Lighttpd Web Server: lighttpd.
295
Starting crond: OK
296
Starting Network Interface Plugging Daemon: eth0.
297
Stopping Bootlog daemon: bootlogd.
298

    
299
Poky (Yocto Project Reference Distro) 1.5.4 mitysom-5csx /dev/ttyS0
300

    
301
mitysom-5csx login:
(2-2/4) Go to top
Add picture from clipboard (Maximum size: 1 GB)