Mity CPU Platforms » MitySOM-5CSX Altera Cyclone V

[    0.000000] On node 0 totalpages: 65536

[    0.000000] free_area_init_node: node 0, pgdat 80a69740, node_mem_map 8fdf9000

[    0.000000]   Normal zone: 512 pages used for memmap

[    0.000000]   Normal zone: 0 pages reserved

[    0.000000]   Normal zone: 65536 pages, LIFO batch:15

[    0.000000] percpu: Embedded 14 pages/cpu @8fdca000 s26764 r8192 d22388 u57344

[    0.000000] pcpu-alloc: s26764 r8192 d22388 u57344 alloc=14*4096

[    0.000000] pcpu-alloc: [0] 0 [0] 1 

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024

[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p3 rw rootwait mem=256M

[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)

[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

[    0.000000] Memory: 249820K/262144K available (6144K kernel code, 446K rwdata, 1388K rodata, 1024K init, 153K bss, 12324K reserved, 0K cma-reserved, 0K highmem)

[    0.000000] Virtual kernel memory layout:

                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)

                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)

                   vmalloc : 0x90800000 - 0xff800000   (1776 MB)

                   lowmem  : 0x80000000 - 0x90000000   ( 256 MB)

                   pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)

                   modules : 0x7f000000 - 0x7fe00000   (  14 MB)

                     .text : 0x80008000 - 0x80700000   (7136 kB)

                     .init : 0x80900000 - 0x80a00000   (1024 kB)

                     .data : 0x80a00000 - 0x80a6faec   ( 447 kB)

                      .bss : 0x80a6faec - 0x80a961a4   ( 154 kB)

[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

[    0.000000] Hierarchical RCU implementation.

[    0.000000] 	Build-time adjustment of leaf fanout to 32.

[    0.000000] NR_IRQS:16 nr_irqs:16 16

[    0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x02460000

[    0.000000] L2C-310 erratum 769419 enabled

[    0.000000] L2C-310 enabling early BRESP for Cortex-A9

[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9

[    0.000000] L2C-310 ID prefetch enabled, offset 1 lines

[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled

[    0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB

[    0.000000] L2C-310: CACHE_ID 0x410030c9, AUX_CTRL 0x76460001

[    0.000000] GIC: PPI13 is secure or misconfigured

[    0.000000] GIC: PPI13 is secure or misconfigured

[    0.000000] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns

[    0.000008] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns

[    0.000021] Switching to timer-based delay loop, resolution 10ns

[    0.000296] Console: colour dummy device 80x30

[    0.000321] Calibrating delay loop (skipped), value calculated using timer frequency.. 200.00 BogoMIPS (lpj=1000000)

[    0.000339] pid_max: default: 32768 minimum: 301

[    0.000463] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.000475] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[    0.001233] CPU: Testing write buffer coherency: ok

[    0.001268] ftrace: allocating 21557 entries in 64 pages

[    0.050278] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000

[    0.050542] Setting up static identity map for 0x100000 - 0x100058

[    1.059722] CPU1: failed to come online

[    1.059790] Brought up 1 CPUs

[    1.059801] SMP: Total of 1 processors activated (200.00 BogoMIPS).

[    1.059807] CPU: All CPU(s) started in SVC mode.

[    1.060766] devtmpfs: initialized

[    1.068121] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

[    1.068402] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns

[    1.068424] futex hash table entries: 512 (order: 3, 32768 bytes)

[    1.068628] pinctrl core: initialized pinctrl subsystem

[    1.069115] NET: Registered protocol family 16

[    1.070053] DMA: preallocated 256 KiB pool for atomic coherent allocations

[    1.071338] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.

[    1.071348] hw-breakpoint: maximum watchpoint size is 4 bytes.

[    1.098679] vgaarb: loaded

[    1.098980] SCSI subsystem initialized

[    1.099264] usbcore: registered new interface driver usbfs

[    1.099337] usbcore: registered new interface driver hub

[    1.099410] usbcore: registered new device driver usb

[    1.101230] pps_core: LinuxPPS API ver. 1 registered

[    1.101240] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>

[    1.101264] PTP clock support registered

[    1.101287] EDAC MC: Ver: 3.0.0

[    1.101938] FPGA manager framework

[    1.102193] fpga-region soc:base-fpga-region: FPGA Region probed

[    1.103274] clocksource: Switched to clocksource timer1

[    1.143469] NET: Registered protocol family 2

[    1.144190] TCP established hash table entries: 2048 (order: 1, 8192 bytes)

[    1.144228] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)

[    1.144276] TCP: Hash tables configured (established 2048 bind 2048)

[    1.144347] UDP hash table entries: 256 (order: 1, 8192 bytes)

[    1.144379] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[    1.144554] NET: Registered protocol family 1

[    1.145002] RPC: Registered named UNIX socket transport module.

[    1.145011] RPC: Registered udp transport module.

[    1.145016] RPC: Registered tcp transport module.

[    1.145022] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    1.145037] PCI: CLS 0 bytes, default 64

[    1.147294] workingset: timestamp_bits=30 max_order=16 bucket_order=0

[    1.158519] NFS: Registering the id_resolver key type

[    1.158548] Key type id_resolver registered

[    1.158555] Key type id_legacy registered

[    1.158600] ntfs: driver 2.1.32 [Flags: R/W].

[    1.158981] jffs2: version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.

[    1.160386] io scheduler noop registered (default)

[    1.170141] dma-pl330 ffe01000.pdma: Loaded driver for PL330 DMAC-341330

[    1.170159] dma-pl330 ffe01000.pdma: 	DBUFF-512x8bytes Num_Chans-8 Num_Peri-32 Num_Events-8

[    1.175195] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[    1.176626] console [ttyS0] disabled

[    1.176669] ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 45, base_baud = 6250000) is a 16550A

[    1.625888] console [ttyS0] enabled

[    1.631054] brd: module loaded

[    1.634073] at24 0-0050: 2048 byte 24c16 EEPROM, writable, 1 bytes/write

[    1.640550] cadence-qspi ff705000.spi: n25q128a11 (16384 Kbytes)

[    1.645694] 6 ofpart partitions found on MTD device ff705000.spi.0

[    1.650556] Creating 6 MTD partitions on "ff705000.spi.0":

[    1.654774] 0x000000000000-0x000000040000 : "Preloader Image 0-3"

[    1.660714] 0x000000040000-0x000000050000 : "U-Boot Env"

[    1.665845] 0x000000050000-0x000000060000 : "DTB"

[    1.670345] 0x000000060000-0x0000000e0000 : "U-Boot"

[    1.675169] 0x0000000e0000-0x0000008e0000 : "Kernel"

[    1.679961] 0x0000008e0000-0x000001000000 : "FPGA"

[    1.685167] libphy: Fixed MDIO Bus: probed

[    1.688406] CAN device driver interface

[    1.691733] c_can_platform ffc00000.can: c_can_platform device registered (regs=908eb000, irq=26)

[    1.700057] c_can_platform ffc01000.can: c_can_platform device registered (regs=908ed000, irq=30)

[    1.708205] stmmac - user ID: 0x10, Synopsys ID: 0x37

[    1.711941]  Ring mode enabled

[    1.713719]  DMA HW capability register supported

[    1.716933]  Enhanced/Alternate descriptors

[    1.719803] 	Enabled extended descriptors

[    1.722498]  RX Checksum Offload Engine supported

[    1.725903] 	COE Type 2

[    1.727043]  TX Checksum insertion supported

[    1.729996]  Enable RX Mitigation via HW Watchdog Timer

[    2.828855] libphy: stmmac: probed

[    2.830956] eth%d: PHY ID 00221611 at 3 IRQ POLL (stmmac-0:03) active

[    2.837888] dwc2 ffb40000.usb: EPs: 16, dedicated fifos, 8064 entries in SPRAM

[    2.844419] dwc2 ffb40000.usb: DWC OTG Controller

[    2.847839] dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1

[    2.853626] dwc2 ffb40000.usb: irq 47, io mem 0x00000000

[    2.857918] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    2.863423] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    2.869321] usb usb1: Product: DWC OTG Controller

[    2.872712] usb usb1: Manufacturer: Linux 4.9.78-ltsi-g818b616 dwc2_hsotg

[    2.878197] usb usb1: SerialNumber: ffb40000.usb

[    2.882227] hub 1-0:1.0: USB hub found

[    2.884783] hub 1-0:1.0: 1 port detected

[    2.888290] usbcore: registered new interface driver usb-storage

[    2.893101] usbcore: registered new interface driver usbserial

[    2.897712] usbcore: registered new interface driver usbserial_generic

[    2.902966] usbserial: USB Serial support registered for generic

[    2.908109] mousedev: PS/2 mouse device common for all mice

[    2.913051] rtc-abx80x 0-0069: model 1805, revision 2.3, lot 358, wafer 16, uid 140

[    2.920022] rtc-abx80x 0-0069: Oscillator failure, data is invalid.

[    2.925229] rtc-abx80x 0-0069: rtc core: registered abx8xx as rtc0

[    2.930171] i2c /dev entries driver

[    2.933077] lm73 0-004c: sensor 'lm73'

[    3.187503] EDAC MC: No ECC/ECC disabled [0x000A8042]

[    3.191615] Synopsys Designware Multimedia Card Interface Driver

[    3.196760] dw_mmc ff704000.dwmmc0: IDMAC supports 32-bit address mode.

[    3.202092] dw_mmc ff704000.dwmmc0: Using internal DMA controller.

[    3.206988] dw_mmc ff704000.dwmmc0: Version ID is 240a

[    3.210865] dw_mmc ff704000.dwmmc0: DW MMC controller at irq 39,32 bit host data width,1024 deep fifo

[    3.243368] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)

[    3.273335] dw_mmc ff704000.dwmmc0: 1 slots initialized

[    3.295928] lp5562 0-0030: internal clock used

[    3.300740] ledtrig-cpu: registered to indicate activity on CPUs

[    3.305702] usbcore: registered new interface driver usbhid

[    3.309955] usbhid: USB HID core driver

[    3.312851] fpga_manager fpga0: Altera SOCFPGA FPGA Manager registered

[    3.318627] altera_hps2fpga_bridge ff400000.fpga_bridge: fpga bridge [lwhps2fpga] registered

[    3.326050] altera_hps2fpga_bridge ff500000.fpga_bridge: fpga bridge [hps2fpga] registered

[    3.333643] oprofile: no performance counters

[    3.336808] oprofile: using timer interrupt.

[    3.340018] NET: Registered protocol family 17

[    3.343178] NET: Registered protocol family 15

[    3.346341] can: controller area network core (rev 20120528 abi 9)

[    3.351263] NET: Registered protocol family 29

[    3.354439] can: raw protocol (rev 20120528)

[    3.357397] can: broadcast manager protocol (rev 20161123 t)

[    3.361743] can: netlink gateway (rev 20130117) max_hops=1

[    3.366192] 8021q: 802.1Q VLAN Support v1.8

[    3.369105] Key type dns_resolver registered

[    3.372176] ThumbEE CPU extension supported.

[    3.375170] Registering SWP/SWPB emulation handler

[    3.378802] usb 1-1: new full-speed USB device number 2 using dwc2

[    3.383792] dwc2 ffb40000.usb: XactErr

[    3.386435] dwc2 ffb40000.usb: XactErr

[    3.389004] dwc2 ffb40000.usb: XactErr

[    3.395215] input: gpio_keys as /devices/platform/gpio_keys/input/input0

[    3.401464] ttyS0 - failed to request DMA

[    3.404439] Waiting for root device /dev/mmcblk0p3...

[    3.425313] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)

[    3.433840] mmc0: new high speed SDHC card at address aaaa

[    3.438566] mmcblk0: mmc0:aaaa SA08G 7.40 GiB 

[    3.444003]  mmcblk0: p1 p2 p3

[    3.524832] EXT4-fs (mmcblk0p3): mounting ext3 file system using the ext4 subsystem

[    3.562517] random: fast init done

[    3.593300] usb 1-1: device descriptor read/64, error -71

[    3.606764] EXT4-fs (mmcblk0p3): warning: mounting fs with errors, running e2fsck is recommended

[    3.617418] EXT4-fs (mmcblk0p3): recovery complete

[    3.622446] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)

[    3.629278] VFS: Mounted root (ext3 filesystem) on device 179:3.

[    3.642815] devtmpfs: mounted

[    3.645785] Freeing unused kernel memory: 1024K

[    3.713396] dwc2 ffb40000.usb: XactErr

[    3.715985] dwc2 ffb40000.usb: XactErr

[    3.718618] dwc2 ffb40000.usb: XactErr

[    3.923333] usb 1-1: device descriptor read/64, error -71

[    4.253335] usb 1-1: new full-speed USB device number 3 using dwc2

[    4.258355] dwc2 ffb40000.usb: XactErr

[    4.261351] dwc2 ffb40000.usb: XactErr

[    4.264285] dwc2 ffb40000.usb: XactErr

[    4.278217] udevd[79]: starting version 3.2.2

[    4.349867] udevd[80]: starting eudev-3.2.2

[    4.473380] usb 1-1: device descriptor read/64, error -71

[    4.593548] dwc2 ffb40000.usb: XactErr

[    4.596148] dwc2 ffb40000.usb: XactErr

[    4.598759] dwc2 ffb40000.usb: XactErr

[    4.803355] usb 1-1: device descriptor read/64, error -71

[    4.923375] usb usb1-port1: attempt power cycle

[    6.109517] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null)

[    6.301038] rtc-abx80x 0-0069: Oscillator failure, data is invalid.

[    7.096330] socfpga-dwmac ff702000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported

[    7.103896] socfpga-dwmac ff702000.ethernet eth0: registered PTP clock

[   17.161172] NET: Registered protocol family 10

[   17.182791] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[  126.343338] random: crng init done

[  305.143275] EXT4-fs (mmcblk0p3): error count since last fsck: 6

[  305.147885] EXT4-fs (mmcblk0p3): initial error at time 1620767484: ext4_mb_generate_buddy:805

[  305.155115] EXT4-fs (mmcblk0p3): last error at time 1605566430: ext4_mb_generate_buddy:758