Project

General

Profile

RE: MityDSP-L138F Boot issue, I2C0 (PCB Dev Post) » BOOT4.txt

Jon Cox, 11/03/2023 04:15 PM

 
1
▒OMAP-L138/AM-1808/AM-1810 initialization passed!
2
Configuring 256MB mDDR
3
                      Booting TI User Boot Loader
4
        UBL Version: 1.65:2.28.1 BuiltJul 11 2011 12:49:53
5
        UBL Flashtype: SPI
6
Starting SPI Memory Copy...
7
Valid magicnum, 0x55424CBB, found at offset 0x00010000.
8
   DONE
9
Jumping to entry point at 0xC1080000.
10

    
11

    
12
U-Boot 2009.11-00004-gabfcd79 (Jan 03 2018 - 11:30:43)
13

    
14
I2C:   ready
15
DRAM:  256 MB
16
NAND:  512 MiB
17
MMC:   davinci: 0
18
In:    serial
19
Out:   serial
20
Err:   serial
21
ARM    Clock : 300000000 Hz
22
DDR    Clock : 150000000 Hz
23
EMIFA  CLock : 100000000 Hz
24
DSP    Clock : 300000000 Hz
25
ASYNC3 Clock : 150000000 Hz
26
Enet  config : 2
27
MMC 0 Enable : 1
28
Resetting ethernet phy
29
Net:   Ethernet PHY: GENERIC @ 0x03 [0x8]
30

    
31
Hit any key to stop autoboot:  0
32
Device: davinci
33
Manufacturer ID: 3
34
OEM: 5344
35
Name: SC16G
36
Tran Speed: 25000000
37
Rd Block Len: 512
38
SD version 2.0
39
High Capacity: Yes
40
Capacity: 15931539456
41
Bus Width: 4-bit
42
Loading file "/boot/uImage" from mmc device 0:1 (xxa1)
43
2544888 bytes read
44
## Booting kernel from Legacy Image at c0700000 ...
45
   Image Name:   Linux-3.2.0
46
   Image Type:   ARM Linux Kernel Image (uncompressed)
47
   Data Size:    2544824 Bytes =  2.4 MB
48
   Load Address: c0008000
49
   Entry Point:  c0008000
50
   Verifying Checksum ... OK
51
   Loading Kernel Image ... OK
52
OK
53

    
54
Starting kernel ...
55

    
56
Uncompressing Linux... done, booting the kernel.
57
Linux version 3.2.0 (adam@intelligen-adam) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #4 PREEMPT Thu May 25 15:50:07 CDT 2023
58
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
59
CPU: VIVT data cache, VIVT instruction cache
60
Machine: MityDSP-L138/MityARM-1808
61
Ignoring unrecognised tag 0x42000101
62
Memory policy: ECC disabled, Data cache writethrough
63
DaVinci da850/omap-l138/am18x variant 0x1
64
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 24384
65
Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/mmcblk0p1 rw,rootwait ip=1.2.3.4::1.2.3.1:255.255.255.248
66
PID hash table entries: 512 (order: -1, 2048 bytes)
67
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
68
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
69
Memory: 96MB = 96MB total
70
Memory: 91336k/91336k available, 6968k reserved, 0K highmem
71
Virtual kernel memory layout:
72
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
73
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
74
    vmalloc : 0xc6800000 - 0xfea00000   ( 898 MB)
75
    lowmem  : 0xc0000000 - 0xc6000000   (  96 MB)
76
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
77
      .text : 0xc0008000 - 0xc053476c   (5298 kB)
78
      .init : 0xc0535000 - 0xc055d000   ( 160 kB)
79
      .data : 0xc055e000 - 0xc05bdbe0   ( 383 kB)
80
       .bss : 0xc05bdc04 - 0xc05ea610   ( 179 kB)
81
NR_IRQS:245
82
Console: colour dummy device 80x30
83
Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
84
pid_max: default: 32768 minimum: 301
85
Mount-cache hash table entries: 512
86
CPU: Testing write buffer coherency: ok
87
devtmpfs: initialized
88
DaVinci: 144 gpio irqs
89
print_constraints: dummy:
90
NET: Registered protocol family 16
91
baseboard_pre_init: Entered
92
mityomapl138_setup_nand: using 8 bit data
93
baseboard_init [IndustrialIO]...
94
bio: create slab <bio-0> at 0
95
SCSI subsystem initialized
96
usbcore: registered new interface driver usbfs
97
usbcore: registered new interface driver hub
98
usbcore: registered new device driver usb
99
print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV
100
print_constraints: VDCDC2: 1800 mV
101
print_constraints: VDCDC3: 1200 mV
102
print_constraints: LDO1: 1800 mV
103
print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV
104
Advanced Linux Sound Architecture Driver Version 1.0.24.
105
Switching to clocksource timer0_1
106
musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
107
Waiting for USB PHY clock good...
108
musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using PIO, IRQ 58
109
NET: Registered protocol family 2
110
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
111
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
112
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
113
TCP: Hash tables configured (established 4096 bind 4096)
114
TCP reno registered
115
UDP hash table entries: 256 (order: 0, 4096 bytes)
116
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
117
NET: Registered protocol family 1
118
RPC: Registered named UNIX socket transport module.
119
RPC: Registered udp transport module.
120
RPC: Registered tcp transport module.
121
RPC: Registered tcp NFSv4.1 backchannel transport module.
122
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
123
msgmni has been set to 178
124
io scheduler noop registered (default)
125
start plist test
126
end plist test
127
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
128
serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A
129
serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A
130
console [ttyS1] enabled
131
serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A
132
brd: module loaded
133
at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
134
MityOMAPL138: Found MAC = c4:ff:bc:70:17:0b
135
MityOMAPL138: Part Number = L138-FI-236-RL
136
ONFI flash detected
137
ONFI param page 0 valid
138
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP)
139
Bad block table found at page 262080, version 0x01
140
Bad block table found at page 262016, version 0x01
141
Creating 2 MTD partitions on "davinci_nand.1":
142
0x000000000000-0x000008000000 : "rootfs"
143
0x000008000000-0x000020000000 : "homefs"
144
davinci_nand davinci_nand.1: controller rev. 2.5
145
spi_davinci spi_davinci.1: DMA: supported
146
spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
147
m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes)
148
Creating 8 MTD partitions on "m25p80":
149
0x000000000000-0x000000010000 : "ubl"
150
0x000000010000-0x000000090000 : "u-boot"
151
0x000000090000-0x0000000a0000 : "u-boot-env"
152
0x0000000a0000-0x0000000b0000 : "periph-config"
153
No LCD configured
154
MII PHY configured
155
0x0000000b0000-0x000000100000 : "reserved"
156
0x000000100000-0x000000400000 : "kernel"
157
0x000000400000-0x000000600000 : "fpga"
158
0x000000600000-0x000000800000 : "spare"
159
spi_davinci spi_davinci.1: cs2 >= max 2
160
spi_davinci spi_davinci.1: can't create new device for dsd1791
161
spi_davinci spi_davinci.1: Controller at 0xfef0e000
162
CAN device driver interface
163
mcp251x spi1.1: MCP251x didn't enter in conf mode after reset
164
mcp251x spi1.1: Probe failed
165
mcp251x spi1.1: probe failed
166
davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
167
davinci_mdio davinci_mdio.0: detected phy mask fffffff7
168
davinci_mdio.0: probed
169
davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown
170
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
171
ohci ohci.0: DA8xx OHCI
172
ohci ohci.0: new USB bus registered, assigned bus number 1
173
Waiting for USB PHY clock good...
174
ohci ohci.0: irq 59, io mem 0x01e25000
175
hub 1-0:1.0: USB hub found
176
hub 1-0:1.0: 1 port detected
177
Initializing USB Mass Storage driver...
178
usbcore: registered new interface driver usb-storage
179
USB Mass Storage support registered.
180
mousedev: PS/2 mouse device common for all mice
181
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
182
omap_rtc: RTC power up reset detected
183
omap_rtc: already running
184
i2c /dev entries driver
185
cpuidle: using governor ladder
186
cpuidle: using governor menu
187
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
188
usbcore: registered new interface driver usbhid
189
usbhid: USB HID core driver
190
mmc0: new high speed SDHC card at address e624
191
mmcblk0: mmc0:e624 SC16G 14.8 GiB
192
 mmcblk0: p1
193
ALSA device list:
194
  No soundcards found.
195
TCP cubic registered
196
NET: Registered protocol family 17
197
can: controller area network core (rev 20090105 abi 8)
198
NET: Registered protocol family 29
199
can: raw protocol (rev 20090105)
200
console [netcon0] enabled
201
netconsole: network logging started
202
omap_rtc omap_rtc: setting system clock to 2000-01-19 01:02:14 UTC (948243734)
203
davinci_mdio davinci_mdio.0: resetting idled controller
204
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201)
205
PHY: 0:03 - Link is Up - 100/Full
206
IP-Config: Complete:
207
     device=eth0, addr=1.2.3.4, mask=255.255.255.248, gw=1.2.3.1,
208
     host=1.2.3.4, domain=, nis-domain=(none),
209
     bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
210
kjournald starting.  Commit interval 5 seconds
211
EXT3-fs (mmcblk0p1): using internal journal
212
EXT3-fs (mmcblk0p1): 2 orphan inodes deleted
213
EXT3-fs (mmcblk0p1): recovery complete
214
EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
215
VFS: Mounted root (ext3 filesystem) on device 179:1.
216
devtmpfs: mounted
217
Freeing init memory: 160K
218
Failed to mount /sys/kernel/security: No such file or directory
219

    
220
Welcome to The Ångström Distribution!
221

    
222
NET: Registered protocol family 10
223
Starting LSB: The RPC portmapper...
224
Starting udev Coldplug all Devices...
225
Starting Temporary Directory...
226
Starting Remount API VFS...
227
Starting udev Kernel Device Manager...
228
Starting Journal Service...
229
Started Journal Service                                                [  OK  ]
230
Starting Load Kernel Modules...
231
Starting POSIX Message Queue File System...
232
udevd[1077]: starting version 182
233
Started Set Up Additional Binary Formats                               [  OK  ]
234
Started Huge Pages File System                                         [  OK  ]
235
Starting Debug File System...
236
Starting Apply Kernel Variables...
237
Disabling lock debugging due to kernel taint
238
Starting File System Check on Root Device...
239
DSPLINK Module (1.65.00.03) created on Date: Aug 10 2012 Time: 16:33:03
240
Started udev Kernel Device Manager                                     [  OK  ]
241
Started LSB: The RPC portmapper                                        [  OK  ]
242
Started Temporary Directory                                            [  OK  ]
243
Started Remount API VFS                                                [  OK  ]
244
Started POSIX Message Queue File System                                [  OK  ]
245
Started Debug File System                                              [  OK  ]
246
Started Apply Kernel Variables                                         [  OK  ]
247
Started File System Check on Root Device                               [  OK  ]
248
Starting Remount Root FS...
249
Started Load Kernel Modules                                            [  OK  ]
250
Started Configuration File System                                      [  OK  ]
251
Started FUSE Control File System                                       [  OK  ]
252
Started Remount Root FS                                                [  OK  ]
253
Started Run pending postinsts                                          [  OK  ]
254
Starting Recreate Volatile Files and Directories...
255
Starting Load Random Seed...
256
Started Machine ID first boot configure                                [  OK  ]
257
Started Load Random Seed                                               [  OK  ]
258
Started Recreate Volatile Files and Directories                        [  OK  ]
259
Starting Avahi mDNS/DNS-SD Stack...
260
Starting LSB: Kernel NFS server support...
261
Starting Timestamping service...
262
Started Timestamping service                                           [  OK  ]
263
Starting Manages Mity_GPP, Mity_DSP, and FPGA binaries deployed to the SOM...
264
Started Manages Mity_GPP, Mity_DSP, and FPGA binarie...oyed to the SOM [  OK  ]
265
Started SSH Key Generation                                             [  OK  ]
266
Starting Permit User Sessions...
267
portmap[1072]: Starting portmap daemon...
268
Starting Login Service...
269
Starting D-Bus System Message Bus...
270
Started Permit User Sessions                                           [  OK  ]
271
nfsserver[1320]: creating NFS state directory: done
272
Started D-Bus System Message Bus                                       [  OK  ]
273
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
274
svc: failed to register lockdv1 RPC service (errno 97).
275
Started Avahi mDNS/DNS-SD Stack                                        [  OK  ]
276
Started Login Service                                                  [  OK  ]
277
nfsserver[1320]: starting 8 nfsd kernel threads: done
278
nfsserver[1320]: starting mountd: done
279
Starting Serial Getty on ttyS1...
280
Started Serial Getty on ttyS1                                          [  OK  ]
281

    
282
.---O---.
283
|       |                  .-.           o o
284
|   |   |-----.-----.-----.| |   .----..-----.-----.
285
|       |   Failed to start LSB: Kernel NFS server support                         [FAILED]
286
See 'systemctl status nfsserver.service' for details.
287
nfsserver[1320]: starting statd: done
288
  | __  |  ---'| '--.|  .-'|     |     |
289
|   |   |  |  |     |---  ||  --'|  |  |  '  | | | |
290
'---'---'--'--'--.  |-----''----''--'  '-----'-'-'-'
291
                -'  |
292
                '---'
293

    
294
The Angstrom Distribution mityomapl138 ttyS1
295

    
296
Angstrom v2012.05 - Kernel 3.2.0
297

    
298
Starting abs_gpp.service...
299
mityomapl138 login: fpga fpga_ctrl: loading the fpga_ctrl module.
300
fpga fpga_ctrl: Found Device ID 00-Base Module (01.01) at C687C000
301
fpga fpga_ctrl: Found Device ID 00-Base Module (01.01) at C687C400
302
abs_gpp.sh[1789]: Starting ABS MityDSP Application:
303
Started abs_gpp.service                                                [  OK  ]
304
Started udev Coldplug all Devices                                      [  OK  ]
305
Starting Getty on tty1...
306
Started Getty on tty1                                                  [  OK  ]
307

    
(2-2/4) Go to top
Add picture from clipboard (Maximum size: 1 GB)