1
|
, pgdat c05f7af0, node_mem_map c0626000
|
2
|
DMA zone: 192 pages used for memmap
|
3
|
DMA zone: 0 pages reserved
|
4
|
DMA zone: 24384 pages, LIFO batch:3
|
5
|
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
|
6
|
pcpu-alloc: [0] 0
|
7
|
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 24384
|
8
|
Kernel command line: mem=96M console=ttyS1,115200n8 mtdparts=nand:128M(rootfs),-(userfs) root=/dev/sda1 rw,rootwait
|
9
|
PID hash table entries: 512 (order: -1, 2048 bytes)
|
10
|
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
|
11
|
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
|
12
|
Memory: 96MB = 96MB total
|
13
|
Memory: 91100k/91100k available, 7204k reserved, 0K highmem
|
14
|
Virtual kernel memory layout:
|
15
|
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
|
16
|
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
|
17
|
vmalloc : 0xc6800000 - 0xfea00000 ( 898 MB)
|
18
|
lowmem : 0xc0000000 - 0xc6000000 ( 96 MB)
|
19
|
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
|
20
|
.text : 0xc0008000 - 0xc056b814 (5519 kB)
|
21
|
.init : 0xc056c000 - 0xc0598000 ( 176 kB)
|
22
|
.data : 0xc0598000 - 0xc05f8560 ( 386 kB)
|
23
|
.bss : 0xc05f8584 - 0xc0625894 ( 181 kB)
|
24
|
NR_IRQS:245
|
25
|
Console: colour dummy device 80x30
|
26
|
Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
|
27
|
pid_max: default: 32768 minimum: 301
|
28
|
Mount-cache hash table entries: 512
|
29
|
CPU: Testing write buffer coherency: ok
|
30
|
devtmpfs: initialized
|
31
|
DaVinci: 144 gpio irqs
|
32
|
print_constraints: dummy:
|
33
|
NET: Registered protocol family 16
|
34
|
baseboard_pre_init: Entered
|
35
|
mityomapl138_setup_nand: using 8 bit data
|
36
|
baseboard_init [IndustrialIO]...
|
37
|
bio: create slab <bio-0> at 0
|
38
|
SCSI subsystem initialized
|
39
|
libata version 3.00 loaded.
|
40
|
usbcore: registered new interface driver usbfs
|
41
|
usbcore: registered new interface driver hub
|
42
|
usbcore: registered new device driver usb
|
43
|
print_constraints: VDCDC1: 1150 <--> 1350 mV at 1200 mV
|
44
|
print_constraints: VDCDC2: 1800 mV
|
45
|
print_constraints: VDCDC3: 1200 mV
|
46
|
print_constraints: LDO1: 1800 mV
|
47
|
print_constraints: LDO2: 2500 <--> 3300 mV at 3300 mV
|
48
|
Advanced Linux Sound Architecture Driver Version 1.0.24.
|
49
|
Switching to clocksource timer0_1
|
50
|
musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
|
51
|
Waiting for USB PHY clock good...
|
52
|
musb-hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn)
|
53
|
musb-hdrc: MHDRC RTL version 1.800
|
54
|
musb-hdrc: setup fifo_mode 2
|
55
|
musb-hdrc: 7/9 max ep, 2624/4096 memory
|
56
|
musb-hdrc musb-hdrc: MUSB HDRC host driver
|
57
|
musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 1
|
58
|
musb-hdrc musb-hdrc: supports USB remote wakeup
|
59
|
usb usb1: default language 0x0409
|
60
|
usb usb1: udev 1, busnum 1, minor = 0
|
61
|
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
|
62
|
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
|
63
|
usb usb1: Product: MUSB HDRC host driver
|
64
|
usb usb1: Manufacturer: Linux 3.2.0 musb-hcd
|
65
|
usb usb1: SerialNumber: musb-hdrc
|
66
|
usb usb1: usb_probe_device
|
67
|
usb usb1: configuration #1 chosen from 1 choice
|
68
|
usb usb1: adding 1-0:1.0 (config #1, interface 0)
|
69
|
hub 1-0:1.0: usb_probe_interface
|
70
|
hub 1-0:1.0: usb_probe_interface - got id
|
71
|
hub 1-0:1.0: USB hub found
|
72
|
hub 1-0:1.0: 1 port detected
|
73
|
hub 1-0:1.0: standalone hub
|
74
|
hub 1-0:1.0: individual port power switching
|
75
|
hub 1-0:1.0: no over-current protection
|
76
|
hub 1-0:1.0: Single TT
|
77
|
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
|
78
|
hub 1-0:1.0: power on to power good time: 10ms
|
79
|
hub 1-0:1.0: local power source is good
|
80
|
hub 1-0:1.0: enabling power on all ports
|
81
|
musb-hdrc musb-hdrc: USB Host mode controller at fee00000 using DMA, IRQ 58
|
82
|
NET: Registered protocol family 2
|
83
|
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
|
84
|
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
|
85
|
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
|
86
|
TCP: Hash tables configured (established 4096 bind 4096)
|
87
|
TCP reno registered
|
88
|
UDP hash table entries: 256 (order: 0, 4096 bytes)
|
89
|
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
|
90
|
NET: Registered protocol family 1
|
91
|
RPC: Registered named UNIX socket transport module.
|
92
|
RPC: Registered udp transport module.
|
93
|
RPC: Registered tcp transport module.
|
94
|
RPC: Registered tcp NFSv4.1 backchannel transport module.
|
95
|
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
|
96
|
msgmni has been set to 177
|
97
|
io scheduler noop registered (default)
|
98
|
start plist test
|
99
|
end plist test
|
100
|
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
|
101
|
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
|
102
|
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
|
103
|
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
|
104
|
usb 1-1: new high-speed USB device number 2 using musb-hdrc
|
105
|
usb 1-1: default language 0x0409
|
106
|
usb 1-1: udev 2, busnum 1, minor = 1
|
107
|
usb 1-1: New USB device found, idVendor=8564, idProduct=4000
|
108
|
usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=5
|
109
|
usb 1-1: Product: GL3220
|
110
|
usb 1-1: Manufacturer: Genesys
|
111
|
usb 1-1: SerialNumber: 000000059
|
112
|
usb 1-1: usb_probe_device
|
113
|
usb 1-1: configuration #1 chosen from 1 choice
|
114
|
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
|
115
|
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
|
116
|
hub 1-0:1.0: port 1 enable change, status 00000503
|
117
|
Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
|
118
|
serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A
|
119
|
serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A
|
120
|
console [ttyS1] enabled
|
121
|
serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A
|
122
|
brd: module loaded
|
123
|
at24 1-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write
|
124
|
MityOMAPL138: Found MAC = 00:50:c2:e6:7a:a1
|
125
|
MityOMAPL138: Part Number = L138-FI-236-RL
|
126
|
ahci ahci: forcing PORTS_IMPL to 0x1
|
127
|
ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
|
128
|
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc
|
129
|
scsi0 : ahci_platform
|
130
|
ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67
|
131
|
ONFI flash detected
|
132
|
ONFI param page 0 valid
|
133
|
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABADAWP)
|
134
|
Bad block table found at page 262080, version 0x01
|
135
|
Bad block table found at page 262016, version 0x01
|
136
|
Creating 2 MTD partitions on "davinci_nand.1":
|
137
|
0x000000000000-0x000008000000 : "rootfs"
|
138
|
0x000008000000-0x000020000000 : "homefs"
|
139
|
davinci_nand davinci_nand.1: controller rev. 2.5
|
140
|
spi_davinci spi_davinci.1: DMA: supported
|
141
|
spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0
|
142
|
------------[ cut here ]------------
|
143
|
WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x54/0x108()
|
144
|
autorequest GPIO-8
|
145
|
Modules linked in:
|
146
|
[<c000d800>] (unwind_backtrace+0x0/0xec) from [<c001d848>] (warn_slowpath_common+0x4c/0x64)
|
147
|
[<c001d848>] (warn_slowpath_common+0x4c/0x64) from [<c001d8f4>] (warn_slowpath_fmt+0x30/0x40)
|
148
|
[<c001d8f4>] (warn_slowpath_fmt+0x30/0x40) from [<c016d830>] (gpio_ensure_requested+0x54/0x108)
|
149
|
[<c016d830>] (gpio_ensure_requested+0x54/0x108) from [<c016da58>] (gpio_direction_output+0x80/0x140)
|
150
|
[<c016da58>] (gpio_direction_output+0x80/0x140) from [<c03546a4>] (davinci_spi_probe+0x334/0x47c)
|
151
|
[<c03546a4>] (davinci_spi_probe+0x334/0x47c) from [<c01a553c>] (platform_drv_probe+0x1c/0x24)
|
152
|
[<c01a553c>] (platform_drv_probe+0x1c/0x24) from [<c01a41f8>] (driver_probe_device+0xd8/0x1c8)
|
153
|
[<c01a41f8>] (driver_probe_device+0xd8/0x1c8) from [<c01a4348>] (__driver_attach+0x60/0x84)
|
154
|
[<c01a4348>] (__driver_attach+0x60/0x84) from [<c01a39a0>] (bus_for_each_dev+0x4c/0x8c)
|
155
|
[<c01a39a0>] (bus_for_each_dev+0x4c/0x8c) from [<c01a3270>] (bus_add_driver+0xa0/0x220)
|
156
|
[<c01a3270>] (bus_add_driver+0xa0/0x220) from [<c01a49a0>] (driver_register+0xbc/0x148)
|
157
|
[<c01a49a0>] (driver_register+0xbc/0x148) from [<c00087a0>] (do_one_initcall+0x94/0x164)
|
158
|
[<c00087a0>] (do_one_initcall+0x94/0x164) from [<c056c218>] (kernel_init+0x78/0x120)
|
159
|
[<c056c218>] (kernel_init+0x78/0x120) from [<c0009d28>] (kernel_thread_exit+0x0/0x8)
|
160
|
---[ end trace c1fc27cd4f832e8a ]---
|
161
|
spi_davinci spi_davinci.1: registered master spi1
|
162
|
spi spi1.0: setup mode 0, 8 bits/w, 30000000 Hz max --> 0
|
163
|
m25p80 spi1.0: m25p64-nonjedec (8192 Kbytes)
|
164
|
Creating 8 MTD partitions on "m25p80":
|
165
|
0x000000000000-0x000000010000 : "ubl"
|
166
|
0x000000010000-0x000000090000 : "u-boot"
|
167
|
0x000000090000-0x0000000a0000 : "u-boot-env"
|
168
|
0x0000000a0000-0x0000000b0000 : "periph-config"
|
169
|
No LCD configured
|
170
|
MII PHY configured
|
171
|
0x0000000b0000-0x000000100000 : "reserved"
|
172
|
0x000000100000-0x000000400000 : "kernel"
|
173
|
0x000000400000-0x000000600000 : "fpga"
|
174
|
0x000000600000-0x000000800000 : "spare"
|
175
|
spi_davinci spi_davinci.1: registered child spi1.0
|
176
|
spi spi1.1: setup mode 0, 8 bits/w, 1000000 Hz max --> 0
|
177
|
spi_davinci spi_davinci.1: registered child spi1.1
|
178
|
spi_davinci spi_davinci.1: Controller at 0xfef0e000
|
179
|
CAN device driver interface
|
180
|
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|
181
|
davinci_mdio davinci_mdio.0: davinci mdio revision 1.5
|
182
|
davinci_mdio davinci_mdio.0: detected phy mask fffffff7
|
183
|
ata1.00: ATA-8: WDC WD1600BEKT-00PVMT0, 01.01A01, max UDMA/133
|
184
|
ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
|
185
|
davinci_mdio.0: probed
|
186
|
davinci_mdio davinci_mdio.0: phy[3]: device 0:03, driver unknown
|
187
|
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
|
188
|
ohci_hcd: block sizes: ed 64 td 64
|
189
|
ohci ohci.0: DA8xx OHCI
|
190
|
ohci ohci.0: new USB bus registered, assigned bus number 2
|
191
|
ohci ohci.0: starting USB controller
|
192
|
Waiting for USB PHY clock good...
|
193
|
ohci ohci.0: created debug files
|
194
|
ohci ohci.0: irq 59, io mem 0x01e25000
|
195
|
ata1.00: configured for UDMA/133
|
196
|
scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEKT-0 01.0 PQ: 0 ANSI: 5
|
197
|
sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
|
198
|
sd 0:0:0:0: Attached scsi generic sg0 type 0
|
199
|
sd 0:0:0:0: [sda] Write Protect is off
|
200
|
ohci ohci.0: OHCI controller state
|
201
|
ohci ohci.0: OHCI 1.0, NO legacy support registers
|
202
|
ohci ohci.0: control 0x083 HCFS=operational CBSR=3
|
203
|
ohci ohci.0: cmdstatus 0x00000 SOC=0
|
204
|
ohci ohci.0: intrstatus 0x00000000
|
205
|
ohci ohci.0: intrenable 0x8000005a MIE RHSC UE RD WDH
|
206
|
ohci ohci.0: hcca frame #0000
|
207
|
ohci ohci.0: roothub.a 00001202 POTPGT=0 NOCP NPS NDP=2(1)
|
208
|
ohci ohci.0: roothub.b 00000000 PPCM=0000 DR=0000
|
209
|
ohci ohci.0: roothub.status 00008000 DRWE
|
210
|
ohci ohci.0: roothub.portstatus [0] 0x00000100 PPS
|
211
|
usb usb2: default language 0x0409
|
212
|
usb usb2: udev 1, busnum 2, minor = 128
|
213
|
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
|
214
|
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
|
215
|
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
|
216
|
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
|
217
|
usb usb2: Product: DA8xx OHCI
|
218
|
usb usb2: Manufacturer: Linux 3.2.0 ohci_hcd
|
219
|
usb usb2: SerialNumber: ohci.0
|
220
|
usb usb2: usb_probe_device
|
221
|
usb usb2: configuration #1 chosen from 1 choice
|
222
|
usb usb2: adding 2-0:1.0 (config #1, interface 0)
|
223
|
hub 2-0:1.0: usb_probe_interface
|
224
|
hub 2-0:1.0: usb_probe_interface - got id
|
225
|
hub 2-0:1.0: USB hub found
|
226
|
hub 2-0:1.0: 1 port detected
|
227
|
sda: sda1
|
228
|
sd 0:0:0:0: [sda] Attached SCSI disk
|
229
|
hub 2-0:1.0: standalone hub
|
230
|
hub 2-0:1.0: no power switching (usb 1.0)
|
231
|
hub 2-0:1.0: no over-current protection
|
232
|
hub 2-0:1.0: power on to power good time: 0ms
|
233
|
hub 2-0:1.0: local power source is good
|
234
|
hub 2-0:1.0: trying to enable port power on non-switchable hub
|
235
|
ohci ohci.0: SetPortFeature(1): POWER
|
236
|
uas 1-1:1.0: usb_probe_interface
|
237
|
uas 1-1:1.0: usb_probe_interface - got id
|
238
|
usbcore: registered new interface driver uas
|
239
|
Initializing USB Mass Storage driver...
|
240
|
usb-storage 1-1:1.0: usb_probe_interface
|
241
|
usb-storage 1-1:1.0: usb_probe_interface - got id
|
242
|
usb-storage: USB Mass Storage device detected
|
243
|
usb-storage: -- associate_dev
|
244
|
usb-storage: Vendor: 0x8564, Product: 0x4000, Revision: 0x0008
|
245
|
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
|
246
|
usb-storage: Transport: Bulk
|
247
|
usb-storage: Protocol: Transparent SCSI
|
248
|
scsi1 : usb-storage 1-1:1.0
|
249
|
usb-storage: *** thread sleeping.
|
250
|
usb-storage 1-1:1.0: device found
|
251
|
usb-storage 1-1:1.0: waiting for device to settle before scanning
|
252
|
usbcore: registered new interface driver usb-storage
|
253
|
USB Mass Storage support registered.
|
254
|
usbcore: registered new interface driver ums-alauda
|
255
|
usbcore: registered new interface driver ums-cypress
|
256
|
usbcore: registered new interface driver ums-datafab
|
257
|
usbcore: registered new interface driver ums_eneub6250
|
258
|
usbcore: registered new interface driver ums-freecom
|
259
|
usbcore: registered new interface driver ums-isd200
|
260
|
usbcore: registered new interface driver ums-jumpshot
|
261
|
usbcore: registered new interface driver ums-onetouch
|
262
|
usbcore: registered new interface driver ums-realtek
|
263
|
usbcore: registered new interface driver ums-sddr09
|
264
|
usbcore: registered new interface driver ums-sddr55
|
265
|
usbcore: registered new interface driver ums-usbat
|
266
|
ohci ohci.0: GetPortStatus(1)
|
267
|
hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000
|
268
|
mousedev: PS/2 mouse device common for all mice
|
269
|
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
|
270
|
omap_rtc: RTC power up reset detected
|
271
|
i2c /dev entries driver
|
272
|
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
|
273
|
davinci_mmc davinci_mmc.1: Using DMA, 4-bit mode
|
274
|
VUB300 Driver rom wait states = 1C irqpoll timeout = 0400
|
275
|
usbcore: registered new interface driver vub300
|
276
|
usbcore: registered new interface driver ushc
|
277
|
usbcore: registered new interface driver usbhid
|
278
|
usbhid: USB HID core driver
|
279
|
mmc0: new high speed SDHC card at address 0001
|
280
|
mmcblk0: mmc0:0001 00000 14.6 GiB
|
281
|
mmcblk0: p1
|
282
|
ALSA device list:
|
283
|
No soundcards found.
|
284
|
TCP cubic registered
|
285
|
NET: Registered protocol family 17
|
286
|
can: controller area network core (rev 20090105 abi 8)
|
287
|
NET: Registered protocol family 29
|
288
|
can: raw protocol (rev 20090105)
|
289
|
regulator_init_complete: LDO2: incomplete constraints, leaving on
|
290
|
regulator_init_complete: LDO1: incomplete constraints, leaving on
|
291
|
regulator_init_complete: VDCDC3: incomplete constraints, leaving on
|
292
|
regulator_init_complete: VDCDC2: incomplete constraints, leaving on
|
293
|
regulator_init_complete: VDCDC1: incomplete constraints, leaving on
|
294
|
console [netcon0] enabled
|
295
|
netconsole: network logging started
|
296
|
omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
|
297
|
kjournald starting. Commit interval 5 seconds
|
298
|
EXT3-fs (sda1): using internal journal
|
299
|
ext3_orphan_cleanup: deleting unreferenced inode 9093135
|
300
|
EXT3-fs (sda1): 1 orphan inode deleted
|
301
|
EXT3-fs (sda1): recovery complete
|
302
|
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
|
303
|
usb-storage: GetMaxLUN command result is 1, data is 2
|
304
|
usb-storage 1-1:1.0: scan complete
|
305
|
EXT3-fs (sda1): mounted filesystem with writeback data mode
|
306
|
VFS: Mounted root (ext3 filesystem) on device 8:1.
|
307
|
devtmpfs: mounted
|
308
|
Freeing init memory: 176K
|
309
|
NET: Registered protocol family 10
|
310
|
>udevd[1130]: starting version 182
|
311
|
udc_core: exports duplicate symbol usb_add_gadget_udc (owned by kernel)
|
312
|
EXT3-fs (mmcblk0): error: can't find ext3 filesystem on dev mmcblk0.
|
313
|
EXT2-fs (mmcblk0): error: can't find an ext2 filesystem on dev mmcblk0.
|
314
|
FAT-fs (mmcblk0): bogus number of reserved sectors
|
315
|
FAT-fs (mmcblk0): Can't find a valid FAT filesystem
|
316
|
VFS: Can't find a Minix filesystem V1 | V2 | V3 on device mmcblk0.
|
317
|
cramfs: wrong magic
|
318
|
FAT-fs (mmcblk0): bogus number of reserved sectors
|
319
|
FAT-fs (mmcblk0): Can't find a valid FAT filesystem
|
320
|
kjournald starting. Commit interval 5 seconds
|
321
|
EXT3-fs (mmcblk0p1): using internal journal
|
322
|
EXT3-fs (mmcblk0p1): recovery complete
|
323
|
EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
|
324
|
davinci_mdio davinci_mdio.0: resetting idled controller
|
325
|
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:03, id=40005201)
|
326
|
ADDRCONF(NETDEV_UP): eth0: link is not ready
|
327
|
PHY: 0:03 - Link is Up - 100/Full
|
328
|
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
|
329
|
eth0: no IPv6 routers present
|