Activity

From 03/31/2012 to 04/29/2012

06:25 PM Software Development: RE: TI C6EZAccel library with MityDSP Platform - OmapL138: Hi Michele,
If you would like to use the full TI DVSDK (including C6EZAccel), you can install it from TI (along wi... Michael Williamson
06:05 PM Software Development: TI C6EZAccel library with MityDSP Platform - OmapL138: Dear Sirs,
does anybody there managed to install and use the C6EZAccel library for the OMAPL138 processor, using the... Michele Canepa

10:19 AM Software Development: RE: uPP/DMA registers: If you are not using the on-Board NAND in your design (e.g., booting to a RAMDISK or off of MMC or something), then t... Michael Williamson
09:52 AM Software Development: RE: uPP/DMA registers: Hi Mike,
Thanks for the prompt reply. Actually the data stream is from an H.264 encoder in an FPGA, so im not sure... Shahzad Malik
08:18 AM Software Development: RE: uPP/DMA registers: Hello Shahzad,
Unfortunately, there is still no UPP driver available. Have you looked at pushing the data in usin... Michael Williamson
04:11 AM Software Development: RE: uPP/DMA registers: Hi Mike,
I am looking for a uPP driver for linux and I was searching around when I came across this thread. I know... Shahzad Malik

12:21 AM Software Development: RE: FS Corruption due to dropping power: Hi Mike,
Thanks for the reply. This is reasuring that it is a FS corruption problem. I have instigated a read onl... Keith Fletcher

12:57 PM Software Development: RE: Starterware EMIFA to FPGA example code: Hi Emmett,
Are you using linux or starterware? On starterware, if you are launching from u-Boot (which configures... Michael Williamson
12:37 PM Software Development: Starterware EMIFA to FPGA example code: Hello,
I have used your "EMIFA_iface" VHDL example to make a simple FPGA to test by reading/writing to registers r... Emmett Bradford

06:31 PM PCB Development: RE: RTC Battery Drain: Hi,
Wanted to follow up on this. We have seen RTC battery drainage, but at the time we looked at it we were using... Michael Williamson
06:28 PM Software Development: RE: FS Corruption due to dropping power: Hi Keith,
I have seen these symptoms before, and I'm pretty sure it's filesystem corruption related (I suspect ude... Michael Williamson

04:29 PM Software Development: FS Corruption due to dropping power: Hi, We are developing a system where the user is unlikely to power down gracefully, even if asked to do so and ultima... Keith Fletcher

09:46 PM PCB Development: RE: SODIMM Pin 53 ...: SPI1_SCS0 is indeed connected to that pin on the module. It is also connected to the chip-select on the on-board SPI... Michael Williamson
09:33 PM PCB Development: SODIMM Pin 53 ...: (Posted on behalf of a customer)
The datasheet for the MITYDSP-L138F shows Pin 53 as reserved, however the Industr... Thomas Catalino

07:40 AM Software Development: RE: StarterWare question ...: Quick note. The new u-Boot command to load up the Starterware image was "bootelf" not "loadelf". I've corrected the... Michael Williamson

02:56 AM Software Development: RE: StarterWare question ...: see [[StarterWare]] Stéphane Peter

02:33 PM Software Development: RE: StarterWare question ...: Hi guys,
Just wanted to give you a heads up that we've been able to get the EVM UART echo example in the TI startw... Michael Williamson

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)