|
1
|
|
|
2
|
root@mitysom-am57x:/# ip address
|
|
3
|
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
|
|
4
|
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
|
|
5
|
inet 127.0.0.1/8 scope host lo
|
|
6
|
valid_lft forever preferred_lft forever
|
|
7
|
inet6 ::1/128 scope host
|
|
8
|
valid_lft forever preferred_lft forever
|
|
9
|
2: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
|
|
10
|
link/sit 0.0.0.0 brd 0.0.0.0
|
|
11
|
3: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
|
|
12
|
link/ether f8:33:31:74:fa:06 brd ff:ff:ff:ff:ff:ff
|
|
13
|
inet6 fe80::fa33:31ff:fe74:fa06/64 scope link
|
|
14
|
valid_lft forever preferred_lft forever
|
|
15
|
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
|
|
16
|
link/ether 3e:c7:a8:e5:dc:ac brd ff:ff:ff:ff:ff:ff
|
|
17
|
inet6 fe80::3cc7:a8ff:fee5:dcac/64 scope link
|
|
18
|
valid_lft forever preferred_lft forever
|
|
19
|
|
|
20
|
|
|
21
|
|
|
22
|
|
|
23
|
root@mitysom-am57x:~# dmesg | grep mdio
|
|
24
|
[ 1.950382] mdio_bus fixed-0: GPIO lookup for consumer reset
|
|
25
|
[ 1.950390] mdio_bus fixed-0: using lookup tables for GPIO lookup
|
|
26
|
[ 1.950398] mdio_bus fixed-0: No GPIO consumer reset found
|
|
27
|
[ 8.019000] mdio_bus 4b2b2400.mdio: GPIO lookup for consumer reset
|
|
28
|
[ 8.019007] mdio_bus 4b2b2400.mdio: using device tree for GPIO lookup
|
|
29
|
[ 8.019029] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/ocp/pruss-soc-bus@4b2a6004/pruss@4b280000/mdio@4b2b2400[0]' - status (0)
|
|
30
|
[ 8.019104] mdio_bus 4b2b2400.mdio: GPIO lookup for consumer reset
|
|
31
|
[ 8.019108] mdio_bus 4b2b2400.mdio: using device tree for GPIO lookup
|
|
32
|
[ 8.019127] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/ocp/pruss-soc-bus@4b2a6004/pruss@4b280000/mdio@4b2b2400[1]' - status (0)
|
|
33
|
[ 8.019166] mdio_bus 4b2b2400.mdio: GPIO lookup for consumer reset
|
|
34
|
[ 8.019170] mdio_bus 4b2b2400.mdio: using device tree for GPIO lookup
|
|
35
|
[ 8.019183] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/pruss-soc-bus@4b2a6004/pruss@4b280000/mdio@4b2b2400[2]'
|
|
36
|
[ 8.019194] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/pruss-soc-bus@4b2a6004/pruss@4b280000/mdio@4b2b2400[2]'
|
|
37
|
[ 8.019200] mdio_bus 4b2b2400.mdio: using lookup tables for GPIO lookup
|
|
38
|
[ 8.019206] mdio_bus 4b2b2400.mdio: No GPIO consumer reset found
|
|
39
|
[ 8.071786] davinci_mdio 4b2b2400.mdio: davinci mdio revision 1.6, bus freq 1000000
|
|
40
|
[ 8.079479] libphy: 4b2b2400.mdio: probed
|
|
41
|
[ 8.086743] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/pruss-soc-bus@4b2a6004/pruss@4b280000/mdio@4b2b2400/ethernet-phy@0[0]'
|
|
42
|
[ 8.089476] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/pruss-soc-bus@4b2a6004/pruss@4b280000/mdio@4b2b2400/ethernet-phy@1[0]'
|
|
43
|
[ 8.089576] davinci_mdio 4b2b2400.mdio: phy[0]: device 4b2b2400.mdio:00, driver unknown
|
|
44
|
[ 8.097667] davinci_mdio 4b2b2400.mdio: phy[1]: device 4b2b2400.mdio:01, driver unknown
|
