Project

General

Profile

Activity

From 03/27/2012 to 04/25/2012

04/25/2012

12:57 PM Software Development: RE: Starterware EMIFA to FPGA example code
Hi Emmett,
Are you using linux or starterware? On starterware, if you are launching from u-Boot (which configures...
Michael Williamson
12:37 PM Software Development: Starterware EMIFA to FPGA example code
Hello,
I have used your "EMIFA_iface" VHDL example to make a simple FPGA to test by reading/writing to registers r...
Emmett Bradford

04/13/2012

06:31 PM PCB Development: RE: RTC Battery Drain
Hi,
Wanted to follow up on this. We have seen RTC battery drainage, but at the time we looked at it we were using...
Michael Williamson
06:28 PM Software Development: RE: FS Corruption due to dropping power
Hi Keith,
I have seen these symptoms before, and I'm pretty sure it's filesystem corruption related (I suspect ude...
Michael Williamson

04/12/2012

04:29 PM Software Development: FS Corruption due to dropping power
Hi, We are developing a system where the user is unlikely to power down gracefully, even if asked to do so and ultima... Keith Fletcher

04/07/2012

09:46 PM PCB Development: RE: SODIMM Pin 53 ...
SPI1_SCS0 is indeed connected to that pin on the module. It is also connected to the chip-select on the on-board SPI... Michael Williamson
09:33 PM PCB Development: SODIMM Pin 53 ...
(Posted on behalf of a customer)
The datasheet for the MITYDSP-L138F shows Pin 53 as reserved, however the Industr...
Thomas Catalino

04/06/2012

07:40 AM Software Development: RE: StarterWare question ...
Quick note. The new u-Boot command to load up the Starterware image was "bootelf" not "loadelf". I've corrected the... Michael Williamson

04/05/2012

02:56 AM Software Development: RE: StarterWare question ...
see [[StarterWare]] Stéphane Peter

04/04/2012

02:33 PM Software Development: RE: StarterWare question ...
Hi guys,
Just wanted to give you a heads up that we've been able to get the EVM UART echo example in the TI startw...
Michael Williamson

03/30/2012

09:19 AM Software Development: RE: Dead board
All clear.
Today, I received a second Base Board - And with this new hardware, the CPU Board runs normally. --> So, ...
Stéphane Peter
06:11 AM Software Development: RE: Write UART2 RS-485 API
Hi Mike:
Thanks for your response. It is working with the 2.6.34-rc1.
It is good timing to assert/de-assert TXE.
...
Joe Hung

03/28/2012

11:15 AM Software Development: RE: Dead board
Hi Mike,
Thank you for your hints.
The good news first: Using the gel files (which is extended with the 150MHz ...
Stéphane Peter
09:32 AM Software Development: RE: Dead board
Well.
The Address 0xFFFD5684 is ARM local ROM code, so it's not surprising that you can't set a breakpoint at that...
Michael Williamson

03/27/2012

08:18 AM Software Development: RE: Write UART2 RS-485 API
Hi Joe,
I am attaching some sample code (a transmit program, and a receive program) that we used to test the RS-48...
Michael Williamson
01:50 AM Software Development: RE: Write UART2 RS-485 API
Sorry I forgot the file. Joe Hung
01:48 AM Software Development: Write UART2 RS-485 API
Hi,
I want to use RS-485 to control other device.
Now I can control uart2 from mitydsp-l138 (not FPGA module), bu...
Joe Hung
07:34 AM Software Development: Dead board
(posted on behalf of a customer)
- I tried to flash a new application to my module. Therefor I performed:...
Thomas Catalino
12:51 AM Software Development: RE: Access to the PHY Registers
Hi Tim,
Thanks for your quick reply - Register 18 is the LED direct control register. I did a few quick tests with t...
Keith Fletcher
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)