Project

General

Profile

Activity

From 04/03/2012 to 05/02/2012

05/02/2012

07:46 AM Software Development: RE: uPP/DMA registers
We have demonstrated capturing as high as 100 MB/sec using UPP in 180 MB blocks without issue. So it's feasible. If... Michael Williamson
03:10 AM Software Development: RE: uPP/DMA registers
@Mike
Thanks for the detailed answer. We are only using the AM1808 as an embedded video server for the stream comi...
Shahzad Malik

04/30/2012

10:12 AM Software Development: RE: uPP/DMA registers
Shahzad, I have not found uPP drivers for the ARM in linux. My suggestion in developing them is to read the TI uPP ... Scott Whitney

04/29/2012

06:25 PM Software Development: RE: TI C6EZAccel library with MityDSP Platform - OmapL138
Hi Michele,
If you would like to use the full TI DVSDK (including C6EZAccel), you can install it from TI (along wi...
Michael Williamson
06:05 PM Software Development: TI C6EZAccel library with MityDSP Platform - OmapL138
Dear Sirs,
does anybody there managed to install and use the C6EZAccel library for the OMAPL138 processor, using the...
Michele Canepa

04/28/2012

10:19 AM Software Development: RE: uPP/DMA registers
If you are not using the on-Board NAND in your design (e.g., booting to a RAMDISK or off of MMC or something), then t... Michael Williamson
09:52 AM Software Development: RE: uPP/DMA registers
Hi Mike,
Thanks for the prompt reply. Actually the data stream is from an H.264 encoder in an FPGA, so im not sure...
Shahzad Malik
08:18 AM Software Development: RE: uPP/DMA registers
Hello Shahzad,
Unfortunately, there is still no UPP driver available. Have you looked at pushing the data in usin...
Michael Williamson
04:11 AM Software Development: RE: uPP/DMA registers
Hi Mike,
I am looking for a uPP driver for linux and I was searching around when I came across this thread. I know...
Shahzad Malik

04/26/2012

12:21 AM Software Development: RE: FS Corruption due to dropping power
Hi Mike,
Thanks for the reply. This is reasuring that it is a FS corruption problem. I have instigated a read onl...
Keith Fletcher

04/25/2012

12:57 PM Software Development: RE: Starterware EMIFA to FPGA example code
Hi Emmett,
Are you using linux or starterware? On starterware, if you are launching from u-Boot (which configures...
Michael Williamson
12:37 PM Software Development: Starterware EMIFA to FPGA example code
Hello,
I have used your "EMIFA_iface" VHDL example to make a simple FPGA to test by reading/writing to registers r...
Emmett Bradford

04/13/2012

06:31 PM PCB Development: RE: RTC Battery Drain
Hi,
Wanted to follow up on this. We have seen RTC battery drainage, but at the time we looked at it we were using...
Michael Williamson
06:28 PM Software Development: RE: FS Corruption due to dropping power
Hi Keith,
I have seen these symptoms before, and I'm pretty sure it's filesystem corruption related (I suspect ude...
Michael Williamson

04/12/2012

04:29 PM Software Development: FS Corruption due to dropping power
Hi, We are developing a system where the user is unlikely to power down gracefully, even if asked to do so and ultima... Keith Fletcher

04/07/2012

09:46 PM PCB Development: RE: SODIMM Pin 53 ...
SPI1_SCS0 is indeed connected to that pin on the module. It is also connected to the chip-select on the on-board SPI... Michael Williamson
09:33 PM PCB Development: SODIMM Pin 53 ...
(Posted on behalf of a customer)
The datasheet for the MITYDSP-L138F shows Pin 53 as reserved, however the Industr...
Thomas Catalino

04/06/2012

07:40 AM Software Development: RE: StarterWare question ...
Quick note. The new u-Boot command to load up the Starterware image was "bootelf" not "loadelf". I've corrected the... Michael Williamson

04/05/2012

02:56 AM Software Development: RE: StarterWare question ...
see [[StarterWare]] Stéphane Peter

04/04/2012

02:33 PM Software Development: RE: StarterWare question ...
Hi guys,
Just wanted to give you a heads up that we've been able to get the EVM UART echo example in the TI startw...
Michael Williamson
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)