Project

General

Profile

Activity

From 04/12/2013 to 05/11/2013

05/09/2013

03:48 PM Software Development: RE: GPIO interrupt in MityOMAP-L138F
I am glad you were able to figure this out, and these notes are helpful. Thanks for posting them.
We have been st...
Michael Williamson
02:58 PM Software Development: RE: GPIO interrupt in MityOMAP-L138F
Hi Mike,
I successfully implemented an interrupt example using FPGA Gpio core and your core libraries on DSP.
Mayb...
Michele Canepa

05/07/2013

07:08 AM Software Development: RE: ethernet over USB don't work
If you want to force HOST mode, then you will need to rebuild the kernel and change the call from:
mityomapl138_us...
Michael Williamson
06:29 AM Software Development: RE: Problem with uPP in DLB
Hi François,
I am a newbie, and trying to create Upp Loopback with MityDSP1810F board.
Can you give your Upp Loopb...
minh tung

05/06/2013

09:59 PM Software Development: RE: ethernet over USB don't work
Sorry for late reply. Thanks for your help at first.
I have removed the RNDIS driver.
What I use is a USB2.0 ethe...
yilin wang
09:59 PM Software Development: RE: ethernet over USB don't work
Sorry for late reply. Thanks for your help at first.
I have removed the RNDIS driver.
What I use is a USB2.0 ethe...
yilin wang

05/04/2013

09:24 AM Software Development: RE: ethernet over USB don't work
I think you are using the wrong approach to do this. The RNDIS driver (g_ether.ko) is to allow IP over USB and is a ... David Rice

05/03/2013

10:59 PM Software Development: ethernet over USB don't work
Hi,
I'm using MityARM-1808 with my own carrier board.
It has a hi-speed USB 2.0 to ethernet controller(smsc7500) co...
yilin wang

05/02/2013

09:55 AM FPGA Development: RE: Verilog codes for MityDSP-L138F
You can use verilog, the Xilinx tools support it. However, all of our refernece code is in VHDL.
It may be possib...
Michael Williamson
09:48 AM FPGA Development: Verilog codes for MityDSP-L138F
Hello,
I am a beginner with FPGA programming and MityDSP-L138F. I know the board currently uses VHDL. Can I write ...
Quoc Lai

04/30/2013

07:30 AM FPGA Development: RE: OFFSET constraint never passes timing
Did not receive it. Michael Williamson

04/29/2013

05:17 PM FPGA Development: RE: OFFSET constraint never passes timing
I tried:
-shreg_extract = checked
-shreg_min_size = 5
No difference.
There is a DCM on i_ema_clk already.
Shou...
Emmett Bradford
04:28 PM FPGA Development: RE: OFFSET constraint never passes timing
If you have it disabled, then it won't happen. Try leaving it enabled and seeting min size to 5.
The other thing ...
Michael Williamson
11:55 AM FPGA Development: RE: OFFSET constraint never passes timing
Thanks Mike,
In Synthesis Properties, HDL Options, I have:
-shreg_extract = unchecked
-shreg_min_size = 3
I see...
Emmett Bradford
10:46 AM FPGA Development: RE: OFFSET constraint never passes timing
Sorry about the -3 vs -2 issue. We will correct that on our next release. However, several designs have been valida... Michael Williamson
09:56 AM FPGA Development: RE: OFFSET constraint never passes timing
The paths that are failing are from the pads to the EMIF module, I don't have any code connecting there.
Also, the...
Emmett Bradford

04/23/2013

01:55 PM FPGA Development: RE: OFFSET constraint never passes timing
Hi,
Two things.
1) You don't need the OFFSET=OUT spec with our IP. It turns out there is an extra clock in the...
Michael Williamson
01:38 PM Software Development: RE: SATA mount point
You can also run "udevadm monitor" to watch for udev activity.
Tim Iskander
01:29 PM Software Development: RE: SATA mount point
Scott,
I'm not sure whats going on. I can't explain why one would work as expected and the other doesn't. Its po...
Jonathan Cormier
11:44 AM Software Development: RE: SATA mount point
the mmc card does not affect the mounting. It behaves the same way with or without it. I don't know if there are an... Scott Whitney
11:39 AM Software Development: RE: SATA mount point
Just as a curiousity, have you tried to see if adding/removing the mmc card affects how the sata drive mounts. Its t... Jonathan Cormier
11:35 AM Software Development: RE: SATA mount point
i am uploading 4 files both my /etc/fstab and the output of fdisk. This is from 2 different systems with different S... Scott Whitney
11:24 AM Software Development: RE: SATA mount point
Scott,
Could you attach your fstab for both machines as well as the output of 'fdisk -l'?
-Jonathan
Jonathan Cormier
11:07 AM Software Development: SATA mount point
_Hello,
I've got a few mityDSP developement kits and am attaching SATA SSD drives to them. They are formated EXT4 w...
Scott Whitney

04/22/2013

02:11 PM FPGA Development: OFFSET constraint never passes timing
I am using the following timing constraints.
If I remember correctly, I started from the industrial I/O example and ...
Emmett Bradford

04/17/2013

06:31 PM Software Development: RE: USB on the go speed
Hi Mike,
It would be great if I can get a copy of your sample code! It would help tremendously if I can get close to...
Lars Majlof
05:03 PM Software Development: RE: USB on the go speed
Hi Lars,
We have found that RNDIS has been very slow as well and we have not used the serial gadget, but I would s...
Michael Williamson
04:20 PM Software Development: USB on the go speed
Hi,
When I configure Linux (3.2.0+) to use the ethernet gadget with RNDIS support, I get poor data transfer speeds. ...
Lars Majlof

04/15/2013

08:54 PM Software Development: RE: release_2012-03-12.run install failed
Check the "BSP Wiki Page":http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Board_Support_Package.... Michael Williamson
08:46 PM Software Development: release_2012-03-12.run install failed
Hello all,
I was failed when i tried to install release_2012-03-12.run,
my OS is Ubuntu 12.04,
it prints in the te...
yilin wang
11:15 AM Software Development: RE: SATA not recognized
Mary,
Thanks for the update. I have created a task to enable SATA by default for the next MDK release. It was set...
Jonathan Cormier
09:24 AM Software Development: RE: SATA not recognized
I got it working.
I compared myconfig to the .config file in the MDK_2012-08-10 linux-davinci directory and they w...
Mary Frantz
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)