Activity
From 05/02/2021 to 05/31/2021
05/21/2021
- 07:12 PM Software Development: RE: Ethernet on MitySoM
- Hi Jonas,
The CSEL switches shouldn't have an effect on the ethernet interface, they are more used during the earl... - 04:27 PM Software Development: RE: Ethernet on MitySoM
- I also tried it at home now (with your image) and I can reproduce the same behavior. So it points directly towards th...
- 03:24 PM Software Development: RE: Ethernet on MitySoM
- Hi Dan,
my plan was to take the board home over the weekend to test out a different router, in the office i test... - 02:37 PM Software Development: RE: Ethernet on MitySoM
- Hi Jonas,
Thank you for providing the serial numbers. I've double checked our production logs and that development... - 08:41 AM Software Development: RE: Ethernet on MitySoM
- Sure,
Baseboard: 1701 8998
SoM: 1803 5616
It's an 5CSX-H6-42A-RC Module
Regards
Jonas
05/20/2021
- 07:57 PM Software Development: RE: Ethernet on MitySoM
- Hi Jonas,
If you are also witnessing this issue with our stock SD card image then it sounds like there could be a ... - 04:59 PM Software Development: RE: Ethernet on MitySoM
- Okay an update:
Skews are set correctly, I read them out with [[ https://github.com/wkz/phytool ]] and could confi...
05/19/2021
- 05:23 PM Software Development: RE: Ethernet on MitySoM
- Hey Dan,
I tried the device tree configurations you mentioned and also the generic ones adapted to my hardware from ...
05/17/2021
- 07:08 PM Software Development: RE: Ethernet on MitySoM
- Hi Jonas,
Looking at the device-tree binding doc for the phy it looks like if you specify the phy address you need... - 10:05 AM Software Development: RE: Ethernet on MitySoM
- Hey Dan,
I checked the kernel configuration in menuconfig and directly in the .config of my kernel and the config ...
05/13/2021
- 09:19 PM Software Development: RE: USB OTG - FTDI Device problems
- Hi Dan,
Thanks for the feedback. That got it working!
05/12/2021
- 03:15 PM Software Development: RE: Ethernet on MitySoM
- Hi Jonas,
You might not have the phy driver built into your kernel, so the phy skews aren't being set. I believe t... - 09:29 AM Software Development: RE: Ethernet on MitySoM
- I apparently used the wrong gpio port, now the reset seems to be working correctly (ethtool shows a PHYAD of 3), but ...
05/11/2021
- 12:01 PM Software Development: RE: Ethernet on MitySoM
- Hey Dan,
thanks for the reply.
I created my dts with the sopc2dts tool, but appended the information given in y...
05/07/2021
- 08:21 PM Software Development: RE: USB OTG - FTDI Device problems
- Hi Travis,
I don't believe the reference project's kernel has built in support for FTDI serial devices. Looking th... - Hello,
I am trying to connect a USB-to-RS232 dongle to the USB-OTG port on the MitySOM-5CSE-L2-3Y8 development kit...
05/05/2021
- 05:59 PM Software Development: RE: Ethernet on MitySoM
- Hi Jonas,
From looking at your boot log it looks like the kernel incorrectly found a PHY at address 31, where it s...
05/04/2021
- Hello,
I have a MitySoM Module and the accompanying dev kit.
To use ssh and scp, i wanted to enable ethernet. For...
Also available in: Atom
Go to top