Mity CPU Platforms

06/13/2011

05:21 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: FPGA configuration

Hi Mike,
FYI, I just had a chance to try a bad configuration file, and the INIT pin was indeed low after programmi... Rob Gillis

06/06/2011

10:35 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Where can I get the files listed on the DSPLink Hello World wiki?

Hi Mads,
Most of the files you need are in the latest tarball release. I've sent you the remaining files, which wi... Gregory Gluszek

07:14 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Where can I get the files listed on the DSPLink Hello World wiki?

Hi
I am also looking for these files...
Could you email me them too?

Many thanks,
Mads Mads Lind Christiansen

06/02/2011

12:17 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: ECC

Ok, Thanks for the quick response. Rob Gillis

12:11 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: ECC

We are using mobile DDR2 x16 for our modules. There is no support for ECC.
-Mike
Michael Williamson

11:56 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: ECC

Hello,
Does the MityDSP L138 module support ECC for the DDR2 RAM? If so, is there software support to enable this... Rob Gillis

05/27/2011

10:00 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: FPGA configuration

Rob,
The INIT_B pin (connected with external pullup to OMAP pin D2, AXR7/EPWMITZ[0]/GP1[15]) is an open drain outp... Michael Williamson

09:37 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: FPGA configuration

Mike, I figured that readback may be an issue, but thanks for confirming it for me. Does the INIT pin provide proof ... Rob Gillis

05/26/2011

08:50 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: FPGA configuration

Hi Rob,
Right now, we don't have an easy way to verify configuration cooked up.
The current MityDSP-L138F famil... Michael Williamson

05:32 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: FPGA configuration

Hello,
I'm trying to figure out an approach for validating the bitfile has been programmed correctly, and for moni... Rob Gillis

05/18/2011

10:46 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: uPP support

Hi Brian,
For the OMAP-L138, pin-muxing is just a fact of life. If you would like to use ethernet and uPP, then i... Michael Williamson

09:32 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: uPP support

Hi Mike
This sounds good. An additional question would be about the pin configuration for the uPP port. In the exc... Brian Rasmussen

08:02 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can't extract release 2011-03

Hi Mike
Thanks for your quick reply. I will try it out.
BR
Brian Brian Rasmussen

07:53 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Can't extract release 2011-03

Hi Brian,
The .run file is really just a shell script. Turns out that it is calling out "/bin/sh" to run the scri... Michael Williamson

03:07 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: Can't extract release 2011-03

Hi
I'm not able to extract the latest board support package release.
I have downloaded the "release_2011-03-31.... Brian Rasmussen

05/17/2011

10:53 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: uPP support

Brian,
You should not have a problem achieving the rates you mentioned above. We have accomplished similar throug... Michael Williamson

10:44 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: uPP support

Hi Mike
We have discussed about the uPP port, and we have decided to try and use it in our project, due to the nic... Brian Rasmussen