Activity

From 03/19/2022 to 04/17/2022

02:26 AM MitySOM-5CSX Embedded Vision Developer's Kit for Basler dart BCON Support: RE: How to adjust the camera exposure time?: Michael Williamson wrote in message#6189:
> You might dump out all the registers and check if there is an AutoTarget... xiang zhang

01:13 PM MitySOM-5CSX Embedded Vision Developer's Kit for Basler dart BCON Support: RE: How to adjust the camera exposure time?: daA1280-54bm
Yes, I ignored the parameter Autotargetbrightness. Thank you. I'll try again.
If I don't adjust th... xiang zhang
12:39 PM MitySOM-5CSX Embedded Vision Developer's Kit for Basler dart BCON Support: RE: How to adjust the camera exposure time?: You might dump out all the registers and check if there is an AutoTargetBrightness and make sure that is disabled. W... Michael Williamson
08:55 AM MitySOM-5CSX Embedded Vision Developer's Kit for Basler dart BCON Support: How to adjust the camera exposure time?: In order to adjust the camera exposure time. I add the code in the picture to main.cpp. Recompile and run demo_app. B... xiang zhang

12:33 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hi Franz,
Based off your boot log the board is stuck at the preloader, before getting into u-boot. The preloader/u... Daniel Vincelette
12:14 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hello Dan,
I made the changes you suggested and the same issue is still there, at this point I don't think the iss... Franz Sattler

11:31 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hi Franz,
One difference that stands out to me is the INPUT/OUTPUT TERMINATIONs used. Because the SOM uses a diffe... Daniel Vincelette
02:23 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hello Dan,
I have attached the .qsys and .qsf files. These have the instances added as well as the row address wid... Franz Sattler

01:40 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Is it possible to use C++ 11?: Also, Make sure to add the "-std=c++11" flag to the g++ compiler to actually enable c++11 features. Jonathan Cormier
01:06 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Is it possible to use C++ 11?: Hello Mike,
That's exactly what I wanted to know. Thank you very much for your prompt reply :)
Vadym Kolesnyk
12:45 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Is it possible to use C++ 11?: Hi Vadym,
Yes. Are you referring to the DSP programming or the ARM programming?
For the ARM, the version of GC... Michael Williamson
12:32 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Is it possible to use C++ 11?: I would know is it possible to apply the c++11 standard during development? Vadym Kolesnyk

06:14 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hi Franz,
For the issue with the 53B SOM hanging at "Initializing SDRAM ECC" the device tree doesn't come into pla... Daniel Vincelette

09:42 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hello Dan,
I did already have those instances added to my .qsf. Before I share my .qsys and .qsf files I would lik... Franz Sattler

12:02 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: MitySOM 5CSX-H6-53B-RC not booting: Hi Franz,
I don't believe changing the pin mux like you have would cause the preloader to hang at initializing the... Daniel Vincelette

Also available in: Atom

Go to top

Mity CPU Platforms