Mity CPU Platforms » MitySOM-335x (ARM Cortex-A8 Based Products)

U-Boot SPL 2011.09 (Jul 23 2013 - 10:01:04)

Texas Instruments Revision detection unimplemented

MityARM335x profile 1 - Model  No: 3354-HX-X38-RC Serial No: 137364

configuring for 512 MB DDR3

Critical Link AM335X Dev Kit -- NAND Page size = 2048k

Critical Link AM335X Dev Kit

PLL configuration complete

OMAP SD/MMC: 0

reading u-boot.img

reading u-boot.img

U-Boot 2011.09-00002-g27623c0-dirty (Oct 24 2013 - 07:41:09)

I2C:   ready

WARNING: Caches not enabled

Skyline u-boot board_init ver 1.0

NAND:  HW ECC Hamming Code selected

512 MiB

MMC:   OMAP SD/MMC danm: 0

Net:   cpsw

Hit any key to stop autoboot:  0

SD/MMC found on device 0

reading uenv.txt

1711 bytes read

Loaded environment from uenv.txt

Importing environment from mmc ...

reading uImage

3561696 bytes read

## Booting kernel from Legacy Image at 80007fc0 ...

   Image Name:   Linux-3.1.0+

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    3561632 Bytes = 3.4 MiB

   Load Address: 80008000

   Entry Point:  80008000

   Verifying Checksum ... OK

   XIP Kernel Image ... OK

OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[    0.000000] Linux version 3.1.0+ (dan@mcg-debian) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #52 Thu Oct 24 10:39:12 MDT 2013

[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f

[    0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

[    0.000000] Machine: mityarm335x

[    0.000000] Memory policy: ECC disabled, Data cache writeback

[    0.000000] AM335X ES1.0 (neon )

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048

[    0.000000] Kernel command line: console=ttyO0,115200n8 video=da8xx:bpp=16 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait ip=none

[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.000000] Memory: 512MB = 512MB total

[    0.000000] Memory: 511672k/511672k available, 12616k reserved, 0K highmem

[    0.000000] Virtual kernel memory layout:

[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)

[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

[    0.000000]     DMA     : 0xff800000 - 0xffe00000   (   6 MB)

[    0.000000]     vmalloc : 0xe0800000 - 0xf8000000   ( 376 MB)

[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)

[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)

[    0.000000]       .text : 0xc0008000 - 0xc06ef000   (7068 kB)

[    0.000000]       .init : 0xc06ef000 - 0xc072b000   ( 240 kB)

[    0.000000]       .data : 0xc072c000 - 0xc07a7ae8   ( 495 kB)

[    0.000000]        .bss : 0xc07a7b0c - 0xc07e4678   ( 243 kB)

[    0.000000] NR_IRQS:396

[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts

[    0.000000] Total of 128 interrupts on 1 active controller

[    0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz

[    0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz

[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms

[    0.000000] Console: colour dummy device 80x30

[    0.000192] Calibrating delay loop... 718.02 BogoMIPS (lpj=3590144)

[    0.059023] pid_max: default: 32768 minimum: 301

[    0.059150] Security Framework initialized

[    0.059253] Mount-cache hash table entries: 512

[    0.059620] CPU: Testing write buffer coherency: ok

[    0.064333] print_constraints: dummy:

[    0.064686] NET: Registered protocol family 16

[    0.065010] GPMC revision 6.0

[    0.066960] OMAP GPIO hardware version 0.1

[    0.069135] omap_l3_smx omap_l3_smx.0: couldn't find resource

[    0.069834] omap_mux_init: Add partition: #1: core, flags: 0

[    0.072865] am33xx_cpsw_init  gmii_sel 0xb4

[    0.072995]  omap_i2c.3: alias fck already exists

[    0.073258]  omap_i2c.2: alias fck already exists

[    0.074853] Registering mcspi 1 [2]

[    0.074896]  omap2_mcspi.1: alias fck already exists

[    0.075089] Registering mcspi 2 [2]

[    0.075122]  omap2_mcspi.2: alias fck already exists

[    0.078526] baseboard_init [MityARM-335x DevKit]...

[    0.078835]  omap_hsmmc.0: alias fck already exists

[    0.079614]  omap_hsmmc.2: alias fck already exists

[    0.081112] Configuring audio...

[    0.081172] Registering mcasp1

[    0.081621]  omap_i2c.1: alias fck already exists

[    0.081834] WLAN GPIO Info.. IRQ = 186 WL_EN = 100 BT_EN = -22

[    0.081846] Bluetooth not Enabled!

[    0.081918] baseboard_setup_wlan: finished

[    0.081959] _omap_mux_get_by_name: Could not find signal mii1_rxclk..uart1_dsrn

[    0.107082] bio: create slab <bio-0> at 0

[    0.109984] SCSI subsystem initialized

[    0.112141] usbcore: registered new interface driver usbfs

[    0.112461] usbcore: registered new interface driver hub

[    0.112670] usbcore: registered new device driver usb

[    0.114307] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz

[    0.115228] tps65910 3-002d: JTAGREVNUM 0x1

[    0.116879] print_constraints: VRTC:

[    0.117571] print_constraints: VIO: at 1500 mV

[    0.120059] print_constraints: VDD1: 600 <--> 1500 mV at 1262 mV normal

[    0.121678] print_constraints: VDD2: at 1137 mV

[    0.121921] print_constraints: VDD3: 5000 mV

[    0.122568] print_constraints: VDIG1: at 1800 mV

[    0.123239] print_constraints: VDIG2: at 1800 mV

[    0.123911] print_constraints: VPLL: at 1800 mV

[    0.124566] print_constraints: VDAC: at 1800 mV

[    0.125224] print_constraints: VAUX1: at 1800 mV

[    0.125898] print_constraints: VAUX2: at 3300 mV

[    0.126572] print_constraints: VAUX33: at 3300 mV

[    0.127237] print_constraints: VMMC: at 3300 mV

[    0.127718] tps65910 3-002d: No interrupt support, no core IRQ

[    0.127914] omap_i2c omap_i2c.2: bus 2 rev4.0 at 100 kHz

[    0.139135] omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz

[    0.140218] Advanced Linux Sound Architecture Driver Version 1.0.24.

[    0.141537] cfg80211: Calling CRDA to update world regulatory domain

[    0.142634] Switching to clocksource gp timer

[    0.149107] Switched to NOHz mode on CPU #0

[    0.157817] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)

[    0.158019] musb-hdrc musb-hdrc.0: dma type: pio

[    0.158917] musb-hdrc musb-hdrc.0: USB OTG mode controller at e080a000 using PIO, IRQ 18

[    0.159105] musb-hdrc musb-hdrc.1: dma type: pio

[    0.159852] musb-hdrc musb-hdrc.1: USB OTG mode controller at e080c800 using PIO, IRQ 19

[    0.160249] NET: Registered protocol family 2

[    0.160440] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)

[    0.160734] TCP established hash table entries: 16384 (order: 5, 131072 bytes)

[    0.161029] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)

[    0.161206] TCP: Hash tables configured (established 16384 bind 16384)

[    0.161218] TCP reno registered

[    0.161231] UDP hash table entries: 256 (order: 0, 4096 bytes)

[    0.161255] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[    0.161434] NET: Registered protocol family 1

[    0.161727] RPC: Registered named UNIX socket transport module.

[    0.161742] RPC: Registered udp transport module.

[    0.161751] RPC: Registered tcp transport module.

[    0.161761] RPC: Registered tcp NFSv4.1 backchannel transport module.

[    0.161974] NetWinder Floating Point Emulator V0.97 (double precision)

[    0.182241] VFS: Disk quotas dquot_6.5.2

[    0.182307] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.182955] msgmni has been set to 999

[    0.183718] io scheduler noop registered

[    0.183733] io scheduler deadline registered

[    0.183796] io scheduler cfq registered (default)

[    0.184742] _regulator_get: tps6116x supply vlcd not found, using dummy regulator

[    0.187667] tps6116x tps6116x: registered backlight controller

[    0.188217] DA8XX FB - options = bpp=16

[    0.188327] da8xx_lcdc da8xx_lcdc.0: GLCD: Found 800x600 panel

[    0.188354] DA8XX FB: 1024 x 768 16 bpp

[    0.202031] Console: switching to colour frame buffer device 128x48

[    0.209669] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[    0.211368] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0

[    0.868407] console [ttyO0] enabled

[    0.872563] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1

[    0.880319] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2

[    0.888002] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3

[    0.895668] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4

[    0.903328] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5

[    0.919453] brd: module loaded

[    0.927409] loop: module loaded

[    0.930873] i2c-core: driver [tsl2550] using legacy suspend method

[    0.937369] i2c-core: driver [tsl2550] using legacy resume method

[    0.943798] at24 2-0050: 256 byte 24c02 EEPROM, read-only, 0 bytes/write

[    0.956647] MityARM-335x: Factory Config Version Wrong (10002)

[    0.964939] m25p80 spi2.0: m25p64-nonjedec (8192 Kbytes)

[    0.970500] Creating 1 MTD partitions on "spi_flash":

[    0.975820] 0x000000000000-0x000000800000 : "NOR User Defined"

[    0.983609] omap2-nand driver initializing

[    0.988224] ONFI flash detected

[    0.991616] ONFI param page 0 valid

[    0.995301] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAWP)

[    1.003683] Creating 8 MTD partitions on "omap2-nand.0":

[    1.009228] 0x000000000000-0x000000020000 : "SPL"

[    1.014139] mtd: partition "SPL" doesn't end on an erase block -- force read-only

[    1.023386] 0x000000020000-0x000000040000 : "SPL.backup1"

[    1.029016] mtd: partition "SPL.backup1" doesn't start on an erase block boundary -- force read-only

[    1.039755] 0x000000040000-0x000000060000 : "SPL.backup2"

[    1.045430] mtd: partition "SPL.backup2" doesn't end on an erase block -- force read-only

[    1.055365] 0x000000060000-0x000000080000 : "SPL.backup3"

[    1.060995] mtd: partition "SPL.backup3" doesn't start on an erase block boundary -- force read-only

[    1.071914] 0x000000080000-0x000000260000 : "U-Boot"

[    1.077135] mtd: partition "U-Boot" doesn't end on an erase block -- force read-only

[    1.086840] 0x000000260000-0x000000280000 : "U-Boot Env"

[    1.092386] mtd: partition "U-Boot Env" doesn't start on an erase block boundary -- force read-only

[    1.103164] 0x000000280000-0x000000780000 : "Kernel"

[    1.110552] 0x000000780000-0x000020000000 : "File System"

[    1.221231] OneNAND driver initializing

[    1.272684] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6

[    1.279132] davinci_mdio davinci_mdio.0: detected phy mask fffffffe

[    1.286351] davinci_mdio.0: probed

[    1.289899] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720

[    1.298661] CAN device driver interface

[    1.302680] CAN bus driver for Bosch D_CAN controller 1.0

[    1.309106] d_can d_can.0: d_can device registered (irq=52, irq_obj=53)

[    1.316716] d_can d_can.1: d_can device registered (irq=55, irq_obj=56)

[    1.324425] usbcore: registered new interface driver cdc_ether

[    1.330653] usbcore: registered new interface driver cdc_subset

[    1.336924] Initializing USB Mass Storage driver...

[    1.342234] usbcore: registered new interface driver usb-storage

[    1.348517] USB Mass Storage support registered.

[    1.353414]  gadget: using random self ethernet address

[    1.358866]  gadget: using random host ethernet address

[    1.364836] usb0: MAC 3e:15:73:ad:41:6c

[    1.368835] usb0: HOST MAC f6:22:82:48:90:ee

[    1.373373]  gadget: Ethernet Gadget, version: Memorial Day 2008

[    1.379650]  gadget: g_ether ready

[    1.383232] musb-hdrc musb-hdrc.0: MUSB HDRC host driver

[    1.388845] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1

[    1.396683] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    1.403778] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    1.411306] usb usb1: Product: MUSB HDRC host driver

[    1.416489] usb usb1: Manufacturer: Linux 3.1.0+ musb-hcd

[    1.422112] usb usb1: SerialNumber: musb-hdrc.0

[    1.427654] hub 1-0:1.0: USB hub found

[    1.431593] hub 1-0:1.0: 1 port detected

[    1.436340] musb-hdrc musb-hdrc.1: MUSB HDRC host driver

[    1.441906] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2

[    1.449712] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

[    1.456806] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    1.464348] usb usb2: Product: MUSB HDRC host driver

[    1.469522] usb usb2: Manufacturer: Linux 3.1.0+ musb-hcd

[    1.475155] usb usb2: SerialNumber: musb-hdrc.1

[    1.480606] hub 2-0:1.0: USB hub found

[    1.484563] hub 2-0:1.0: 1 port detected

[    1.489646] mousedev: PS/2 mouse device common for all mice

[    1.496586] input: ti-tsc-adcc as /devices/platform/tsc/input/input0

[    1.504320] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0

[    1.510975] omap_rtc: already running

[    1.515054] i2c /dev entries driver

[    1.519520] Linux media interface: v0.10

[    1.523865] Linux video capture interface: v2.00

[    1.528984] usbcore: registered new interface driver uvcvideo

[    1.535004] USB Video Class driver (1.1.1)

[    1.942693] usb 2-1: new full speed USB device number 2 using musb-hdrc

[    2.083900] usb 2-1: New USB device found, idVendor=04d8, idProduct=000a

[    2.090889] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0

[    2.098343] usb 2-1: Product: CDC RS-232 Emulation Demo

[    2.103798] usb 2-1: Manufacturer: Microchip Technology Inc.

[    2.592687] omap_i2c omap_i2c.1: controller timed out

[    3.592681] omap_i2c omap_i2c.1: controller timed out

[    4.592674] omap_i2c omap_i2c.1: controller timed out

[    5.612678] omap_i2c omap_i2c.1: controller timed out

[    6.632675] omap_i2c omap_i2c.1: controller timed out

[    7.632676] omap_i2c omap_i2c.1: controller timed out

[    8.652674] omap_i2c omap_i2c.1: controller timed out

[    9.672672] omap_i2c omap_i2c.1: controller timed out

[    9.693679] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec

[    9.700765] cpuidle: using governor ladder

[    9.705593] cpuidle: using governor menu

[    9.713735] usbcore: registered new interface driver usbhid

[    9.719559] usbhid: USB HID core driver

[    9.724599] usbcore: registered new interface driver snd-usb-audio

[    9.754302] tlv320aic26-codec spi1.1: Probing AIC26 SoC CODEC driver

[    9.772964] asoc: tlv320aic26-hifi <-> davinci-mcasp.1 mapping ok

[    9.780478] ALSA device list:

[    9.783610]   #0: MityARM-335X DevKit

[    9.787427] oprofile: hardware counters not available

[    9.792699] oprofile: using timer interrupt.

[    9.797174] nf_conntrack version 0.5.0 (7994 buckets, 31976 max)

[    9.804028] ip_tables: (C) 2000-2006 Netfilter Core Team

[    9.809680] TCP cubic registered

[    9.813080] NET: Registered protocol family 17

[    9.817721] can: controller area network core (rev 20090105 abi 8)

[    9.824266] NET: Registered protocol family 29

[    9.828943] can: raw protocol (rev 20090105)

[    9.833407] can: broadcast manager protocol (rev 20090105 t)

[    9.839345] lib80211: common routines for IEEE802.11 drivers

[    9.845299] Registering the dns_resolver key type

[    9.850270] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3

[    9.858275] ThumbEE CPU extension supported.

[    9.866869] regulator_init_complete: VMMC: incomplete constraints, leaving on

[    9.874834] regulator_init_complete: VAUX33: incomplete constraints, leaving on

[    9.882951] regulator_init_complete: VAUX2: incomplete constraints, leaving on

[    9.890948] regulator_init_complete: VAUX1: incomplete constraints, leaving on

[    9.898961] regulator_init_complete: VDAC: incomplete constraints, leaving on

[    9.906882] regulator_init_complete: VPLL: incomplete constraints, leaving on

[    9.914797] regulator_init_complete: VDIG2: incomplete constraints, leaving on

[    9.922813] regulator_init_complete: VDIG1: incomplete constraints, leaving on

[    9.931272] regulator_init_complete: VDD2: incomplete constraints, leaving on

[    9.939201] regulator_init_complete: VIO: incomplete constraints, leaving on

[    9.947036] regulator_init_complete: VRTC: incomplete constraints, leaving on

[    9.954735] Detected MACID=90:59:af:6d:be:d2

[    9.959761] mmc0: host does not support reading read-only switch. assuming write-enable.

[    9.969315] omap_rtc omap_rtc: setting system clock to 2000-01-01 03:43:09 UTC (946698189)

[    9.978558] Waiting for root device /dev/mmcblk0p2...

[    9.984061] mmc0: new high speed SDHC card at address e624

[    9.990377] mmcblk0: mmc0:e624 SU08G 7.40 GiB

[    9.997052]  mmcblk0: p1 p2 p3

[   10.096462] kjournald starting.  Commit interval 5 seconds

[   10.102232] EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is recommended

[   10.115240] EXT3-fs (mmcblk0p2): using internal journal

[   10.120722] EXT3-fs (mmcblk0p2): recovery complete

[   10.125767] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode

[   10.133049] VFS: Mounted root (ext3 filesystem) on device 179:2.

[   10.139666] Freeing init memory: 240K

INIT: version 2.88 booting

[info] Using makefile-style concurrent boot in runlevel S.

[ ok ] Starting the hotplug events dispatcher: udevd.

[ ok ] Synthesizing the initial hotplug events...done.

[ ok ] Waiting for /dev to be fully populated...done.

[ ok ] Activating swap...done.

[ ok ] Cleaning up temporary files... /tmp.

[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

[ ok ] Activating lvm and md swap...done.

[....] Checking file systems...fsck from util-linux 2.20.1

done.

[....] Mounting local filesystems...[mntent]: line 2 in /etc/fstab is bad

[mntent]: line 3 in /etc/fstab is bad

done.

[ ok ] Activating swapfile swap...done.

[ ok ] Cleaning up temporary files....

[ ok ] Setting kernel variables ...done.

[ ok ] Configuring network interfaces...done.

[....] Starting rpcbind daemon...rpcbind: cannot create socket for udp6

rpcbind: cannot create socket for tcp6

. ok

[ ok ] Starting NFS common utilities: statd idmapd.

[ ok ] Cleaning up temporary files....

INIT: Entering runlevel: 2

[info] Using makefile-style concurrent boot in runlevel 2.

[ ok ] Starting rpcbind daemon...[....] Already running..

[ ok ] Starting NFS common utilities: statd idmapd.

[ ok ] Starting enhanced syslogd: rsyslogd.

[....] Starting web server: apache2apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName

. ok

[ ok ] Starting periodic command scheduler: cron.

[ ok ] Starting system message bus: dbus.

[ ok ] Loading cpufreq kernel modules...done (none).

[ ok ] CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor not available...done.

[ ok ] Starting OpenBSD Secure Shell server: sshd.

Debian GNU/Linux 7.0 arm ttyO0

arm login: root

Password:

Last login: Sat Jan  1 02:07:30 UTC 2000 on ttyO0

Linux arm 3.1.0+ #52 Thu Oct 24 10:39:12 MDT 2013 armv7l

The programs included with the Debian GNU/Linux system are free software;

the exact distribution terms for each program are described in the

individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent

permitted by applicable law.

root@arm:~# less eth0.sh

ifconfig eth0 10.1.2.111 netmask 255.255.252.0 up

root@arm:~# ./eth0.sh

[   45.311962] PHY 0:01 not found

[   45.315619]

[   45.315623] CPSW phy found : id is : 0x7c0f1

root@arm:~# [   48.313231] PHY: 0:00 - Link is Up - 100/Half

root@arm:~# ping 10.1.1.1

PING 10.1.1.1 (10.1.1.1) 56(84) bytes of data.

From 10.1.2.111 icmp_seq=2 Destination Host Unreachable

From 10.1.2.111 icmp_seq=3 Destination Host Unreachable

From 10.1.2.111 icmp_seq=4 Destination Host Unreachable

^C

--- 10.1.1.1 ping statistics ---

4 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2999ms

pipe 3

root@arm:~# ifconfig

eth0      Link encap:Ethernet  HWaddr 90:59:af:6d:be:d2

          inet addr:10.1.2.111  Bcast:10.1.3.255  Mask:255.255.252.0

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:0 (0.0 B)  TX bytes:180 (180.0 B)

          Interrupt:40

lo        Link encap:Local Loopback

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:3 errors:0 dropped:0 overruns:0 frame:0

          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0

          RX bytes:336 (336.0 B)  TX bytes:336 (336.0 B)

root@arm:~#