Activity
From 02/04/2011 to 03/05/2011
03/05/2011
- TI 10:21 AM Software Development: RE: How Do I Get SD Memory Working for Critical Link Carrier Board From Linux
- Michael Williamson wrote:
> Hi David,
> ...
From the referenced page..
The performance numbers can be severely affected if the media is mounted in sync mode. Hot plug scripts in the filesystem mount removable media in sync mode to ens... - MW 10:14 AM Software Development: RE: How Do I Get SD Memory Working for Critical Link Carrier Board From Linux
- Hi David,
TI has published performance numbers for their basic kernel (which our port essentially sits on top of) here:
http://processors.wiki.ti.com/index.php/DaVinci_PSP_03.20.00.11_Device_Driver_Features_and_Performance_Guide#MM... - DK 10:05 AM Software Development: RE: How Do I Get SD Memory Working for Critical Link Carrier Board From Linux
- Tom,
Thanks for your response. We would desire 4MB/s. Do you know how close to that number we could achieve?
David Kasper - TC 09:19 AM Software Development: RE: How Do I Get SD Memory Working for Critical Link Carrier Board From Linux
- Hi David,
What throughput do you need or expect to get? I don't think the SD card is ever going to be as fast as a RAM based file system. I'm not sure what performance you are trying to get to.
Thanks,
Tom
03/04/2011
- DK 09:39 PM Software Development: RE: How Do I Get SD Memory Working for Critical Link Carrier Board From Linux
- Mike,
The micro SD card is functioning with a FAT filesystem in our system. However, the write bandwith is slower then expected at 200KB/s. Writing the same file to RAM yields 14MB/s. Do you have any suggestions on increasing the s...
03/01/2011
- BR 08:25 AM FPGA Development: RE: FPGA example source
- Hi Mike,
thanks for your response. I would like a simple gpio example for the fpga using the fpga_gpio.ko driver from your board support package. If I am able to toggle an IO pin it would be enough for this test.
I have tried to do... - MW 07:28 AM FPGA Development: RE: FPGA example source
- Hi Brian,
I can provide you with an example project if you are still stuck. Sorry for the delay. Please advise what you need.
-Mike
- BR 08:08 AM Software Development: RE: Include Path / Where is the correct source files?
- Hi Mike
Thanks for your response. I am trying to access the EMIF from my application. I will prefer not to write any drivers if possible... The information about "fopen" above is exactly what I'm looking for.
The next steps for a s... - MW 07:26 AM Software Development: RE: Include Path / Where is the correct source files?
- Hi Brian,
Are you trying to write a driver or trying to access the EMIF via your application? Typically, direct memory access must be handled by writing a driver (a kernel module) that supports actions such as mmap (memory mapping). ...
02/28/2011
- Hi
I am trying to interface to the FPGA on a MityDSP-L138 board. I have succeeded building a new kernel, inserting the "fpga_ctrl.ko" module into the kernel and loading the FPGA with the IndustrialIO.bin file from the wiki. The green...
02/26/2011
- MW 02:13 PM Software Development: RE: dsplink debugging issue
- Hi Susan,
It looks like Richard raised this issue on the TI E2E site, here:
http://e2e.ti.com/support/development_tools/code_composer_studio/f/81/t/57359.aspx
The solution appears to be to upgrade to DSPLINK 1.65. We're working...
02/25/2011
- SB 09:39 AM Software Development: RE: dsplink debugging issue
- Was this issue ever resolved? I am running into the same problem.
Thanks,
Susan
02/24/2011
- Hi
I am trying to get the EMIF interface up and running between the uC and the FPGA on a OMAP-L138F Profibus Dev kit board.
At first I would like to verify, I can program the FPGA from the uC using the board support package suppli...