Project

General

Profile

Activity

From 02/26/2012 to 03/26/2012

03/26/2012

09:58 PM Software Development: RE: Access to the PHY Registers
u-boot has the mii commands that let you twiddle the registers, or you can always write a driver :D
I'm not sure wit...
Tim Iskander
09:50 PM Software Development: Access to the PHY Registers
Hi,
This is perhaps a long shot, but I am using a MityARM1808 with development kit, and would like to know if there ...
Keith Fletcher
05:00 AM PCB Development: RE: FPGA no-connects for 45 size FPGA on MityDSP-L138F
I've tried out the "hack" and it works fine; so yes indeed they are floating.
-anders
Anders Joergensen

03/22/2012

08:42 PM Software Development: RE: Kernel Hang Anomaly
Hi Mike,
No need to dig into the file I sent.
I downloaded the 12-05-2011 MDK and rebuilt the kernel
using that c...
Rich Bagdazian
07:13 PM Software Development: RE: Kernel Hang Anomaly
HI Mike,
I'm attaching a file that contains the results of the check of the config.gz file filtering by MMC
both yo...
Rich Bagdazian
06:23 PM Software Development: RE: Kernel Hang Anomaly
Ok, I'll go check the config.gz settings and let you know what I find out. Rich Bagdazian
06:16 PM Software Development: RE: Kernel Hang Anomaly
Hi Rich,
So in the u-Boot, the config block is read on start-up in order to tell u-Boot whether or not it should c...
Michael Williamson
04:58 PM Software Development: RE: Kernel Hang Anomaly
Mike,
Can you elaborate on the significance of the lines in the config response that read:
MMC0 Config : 0
MMC1 Co...
Rich Bagdazian

03/21/2012

08:01 PM Software Development: RE: StarterWare question ...
Hi Stephane -
Unfortunately we believe you are executing the low level initialization code for the TI EVM which i...
Thomas Catalino
02:06 PM Software Development: RE: console redirection
Mike,
So then I just need to change the bootargs to use ttyS2 instead of ttyS1 and the linux kernel console will be ...
Scott Whitney

03/20/2012

05:13 PM Software Development: RE: console redirection
Hi Scott,
For the kernel, you should only need to change the console argument in the bootargs (assuming the pinmux...
Michael Williamson
05:13 PM Software Development: RE: console redirection
Hi Scott,
For the kernel, you should only need to change the console argument in the bootargs (assuming the pinmux...
Michael Williamson
03:53 PM Software Development: console redirection
Hello,
We are using a MItyDSDPL138 with the MityDSP baseboard. We want to use uart1 on the baseboard to interface w...
Scott Whitney
07:34 AM Software Development: RE: StarterWare question ...
Hello,
Thank you for starting this thraed, because I'm facing the same problem as Tim had 2 weeks ago - *and unfor...
Stéphane Peter

03/19/2012

10:30 AM Software Development: RE: 'Fast Boot' DSP
Is the DSP going to be communicating to the ARM via DSPLINK? If so, this may be a challenge as the ARM and DSP need ... Michael Williamson

03/15/2012

10:49 PM Software Development: RE: OMAP GPIO
Hi Mike,
It turns out I didn't enable the Industrial Board I/O option in the kernel. After I enabled it (and enabl...
Simon Wong
08:10 PM Software Development: RE: OMAP GPIO
Hi Simon,
I don't see anything wrong here, but you might want to ensure that the pin-mux configuration is setup fo...
Michael Williamson
05:36 PM Software Development: OMAP GPIO
Hi,
I'm having trouble accessing the OMAP GPIO pins as detailed in the "MityARM-1810 PROFIBUS Dev Kit" documentati...
Simon Wong
01:02 PM Software Development: 'Fast Boot' DSP
(Posted on behalf of a customer):
We need to boot the DSP fast (up and running code in less than 2 secs. ) and the...
Gregory Gluszek

03/13/2012

04:25 PM Software Development: RE: ftdi usb to serial drivers
Thanks Mike that worked. Scott Whitney
12:07 PM Software Development: RE: ftdi usb to serial drivers
You need to install mkimage on your linux machine.... Michael Williamson
12:02 PM Software Development: RE: ftdi usb to serial drivers
Tim,
Thanks for the help. I see the source in the code tree and also see why I couldn't see it in menuconfig. My p...
Scott Whitney

03/12/2012

05:25 PM Software Development: RE: ftdi usb to serial drivers
Scott
The FTDI serial drivers should be in the kernel source tree (as of kernel v 2.6.31)
Its the "USB FTDI Single ...
Tim Iskander
05:14 PM Software Development: ftdi usb to serial drivers
Hello,
I want to access a device across the host USB that uses a FTDI chip to transmit serial data across the usb. ...
Scott Whitney

03/06/2012

04:10 PM Software Development: RE: StarterWare question ...
Also, as a followup question, the StarterWare examples are setting up the system for the evmOMAPL138. For instance, ... Tim Eastham
02:56 PM Software Development: StarterWare question ...
(posted on behalf of a customer)
For the starterware non-os method, I have built some of the starterware examples ...
Thomas Catalino
10:16 AM Software Development: RE: Critical Link Package locations?
At the moment, we don't provide customized packages. The mityomapl138 location was generated during the bitbake buil... Michael Williamson
10:12 AM Software Development: Critical Link Package locations?
(posted on behalf of a customer)
What are the updated feed addresses for the critical link packages?

(these ar...
Thomas Catalino

03/04/2012

06:11 PM Software Development: RE: about boot
Mike,
Thank you very much. I understand.
shengyou gao
04:51 PM Software Development: RE: about boot
The EXT_BOOT# signal drives a small mux circuit on the SOM that changes the boot strap pull-up/pull-down options on t... Michael Williamson
04:56 PM PCB Development: RE: FPGA no-connects for 45 size FPGA on MityDSP-L138F
The bare board PCB for the two variants of the SOM are identical, the only difference is the BOM used for assembly. ... Michael Williamson

03/01/2012

08:28 AM Software Development: about boot
I wonder how the boot mode switch from SPI1 to UART1 using EXT_BOOT# signal? Thank very much. shengyou gao

02/28/2012

08:47 AM PCB Development: FPGA no-connects for 45 size FPGA on MityDSP-L138F
(Posted on behalf of a customer)
We have done a design using the MityDSP-L138F SOM. I tried avoiding using the pin...
Thomas Catalino
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)