Project

General

Profile

Activity

From 03/26/2017 to 04/24/2017

04/11/2017

03:35 AM FPGA Development: RE: FPGA pins in Mity DSP L138F
Hello,
Thank you, that was what I was looking at.
With Regards
Shalini
Shalini K

04/10/2017

06:47 PM Software Development: RE: Does BUSY led mean something on factory new board?
Jacek,
Thank you for confirming which processor was used in the replacement. Based on the lack of the "BOOTME" fro...
Alexander Block
08:17 AM Software Development: RE: Does BUSY led mean something on factory new board?
This processor is without secure-boot. Secure-boot has E following ZWT
There is no BOOTME printed. Other modules ...
Jacek Drewniak
02:12 PM FPGA Development: RE: FPGA pins in Mity DSP L138F
I think your looking for the carrier board design guide. http://www.criticallink.com/wp-content/uploads/2014/01/Mity... Jonathan Cormier
09:57 AM FPGA Development: RE: FPGA pins in Mity DSP L138F
Hello,
Sorry for delay in reply..I was on leave for a few days.Thanks for reply. I think this is not the reply I i...
Shalini K

04/06/2017

03:04 PM Software Development: RE: Does BUSY led mean something on factory new board?
Thank you for confirming the part markings on the OMAP-L138 processor. Best I can tell mean this is likely not a secu... Alexander Block
11:20 AM Software Development: RE: Does BUSY led mean something on factory new board?
I have got OMAPL138EZWT64ALVIW GI D450 527 ZWT
Jacek Drewniak

04/05/2017

03:18 PM Software Development: RE: eMMC support
Thanks guys for information François Tremblay
02:02 PM Software Development: RE: Does BUSY led mean something on factory new board?
Unfortunately we need more clarification on the part number of the processor that was installed. The "B" would presum... Alexander Block
11:05 AM Software Development: RE: Does BUSY led mean something on factory new board?
Is the "E" chip the secure boot option? That would explain why it was not booting up. Michael Williamson
06:52 AM Software Development: RE: Does BUSY led mean something on factory new board?
> Additionally any history about the modules prior operation/history would be helpful
We had to replace OMAPL138*B...
Jacek Drewniak
06:36 AM Software Development: RE: Does BUSY led mean something on factory new board?
> The "BUSY" LED is tied to the FPGA DOUT_BUSY signal which during initial boot into UBoot should not be lit under no... Jacek Drewniak
01:51 PM FPGA Development: RE: FPGA pins in Mity DSP L138F
Shalini,
You can find the mapping of MityDSP-L138F pins from the Edge Connector to the specific balls on both the ...
Alexander Block
08:41 AM FPGA Development: FPGA pins in Mity DSP L138F
Hello,
I have been referring to the schematic showing various components in mity DSP L138F. The referred PDF is at...
Shalini K

04/04/2017

08:58 PM Software Development: RE: Trying to cross compile libsodium.
These instructions worked for me. Thanks. Edwin McKay
08:32 PM Software Development: RE: Trying to cross compile libsodium.
Edwin McKay wrote:
> ok that looks so easy. Thanks for the details. So you did not use the Code Composer Studio at a...
Jonathan Cormier
08:29 PM Software Development: RE: Trying to cross compile libsodium.
ok that looks so easy. Thanks for the details. So you did not use the Code Composer Studio at all. I will try this an... Edwin McKay
02:52 PM Software Development: RE: Trying to cross compile libsodium.
https://download.libsodium.org/doc/installation/
I tried cross compiling and was able to build the library.
<pr...
Jonathan Cormier
02:36 PM Software Development: RE: Trying to cross compile libsodium.
https://github.com/jedisct1/libsodium/releases is the source location.
I created the CCS project as shown in the ...
Edwin McKay
02:03 PM Software Development: RE: Trying to cross compile libsodium.
I'm not familiar with libsodium. Could you provide a link to the source your building? How you are trying to build i... Jonathan Cormier
07:21 PM Software Development: RE: Does BUSY led mean something on factory new board?
Jacek,
Sorry to hear that you're having an issue with one of the modules.
Can you please provide the serial nu...
Alexander Block
08:18 AM Software Development: Does BUSY led mean something on factory new board?
I have got two modules.
One is working, booting, printing stuff on terminal. BUSY led is OFF.
One is not workin...
Jacek Drewniak
06:27 PM Software Development: RE: eMMC support
Hi Francois,
I'm on the project Jon mentioned that is currently using eMMC with the MityDSP-L138F.
In additio...
Gregory Gluszek

04/01/2017

02:24 AM Software Development: Trying to cross compile libsodium.
I am trying to compile the crypto library libsodium for use in the mitydsp. I created a project using the instruction... Edwin McKay

03/31/2017

04:17 PM Software Development: RE: eMMC support
François Tremblay wrote:
> Hi,
>
> We have our own baseboard on which we plug a MITYDSP-L138F.
>
> We are usin...
Jonathan Cormier
11:01 AM Software Development: eMMC support
Hi,
We have our own baseboard on which we plug a MITYDSP-L138F.
We are using a micro SD card on our baseboard f...
François Tremblay

03/29/2017

10:14 PM Software Development: RE: Downloading files from Redmine (using Linux console app)
With the redmine update you now have to deal with the csrf token in order to login. So I created the attached bash fi... Jonathan Cormier
 

Also available in: Atom

Add picture from clipboard (Maximum size: 2 GB)