Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)

04/03/2023

09:15 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

> I understand the only possible solution is to reset radically devkit somehow, but why this strange bug may have hap... Jonathan Cormier

08:06 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

> Did you grab the mityomap-full.tgz file from MDK_2014-01-13? I just want to follow the same steps and make sure it ... Jonathan Cormier

07:51 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

Thanks for the update.
Did you grab the mityomap-full.tgz file from MDK_2014-01-13? I just want to follow the sam... Jonathan Cormier

06:02 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

Sorry if I have described my problem not clearly. Yes, I booted this devkit successfully with my sd card before (abou... Vadym Kolesnyk

01:11 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

Vadym Kolesnyk wrote in message#6294:
> I use the standard devkit. When I had problems with the SD card (for example... Jonathan Cormier

04/01/2023

05:50 AM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

I use the standard devkit. When I had problems with the SD card (for example, bad partition), I got these messages:
... Vadym Kolesnyk

03/31/2023

09:30 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

If this is a custom baseboard without the card detect hooked up. Then this could also happen.
For an example of d... Jonathan Cormier

09:24 PM Software Development: RE: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

That is unexpected. Your boot log looks like everything is correct. It looks similar to if you had no sdcard plugged... Jonathan Cormier

04:01 PM Software Development: Discussion: Kernel hangs on "Waiting for root device /dev/mmcblk0p1..."

I made rootfs on an SD card according to this wiki page (https://support.criticallink.com/redmine/projects/arm9-platf... Vadym Kolesnyk

11:14 AM Software Development: RE: Increasing CPU clock OMAPL138

Hi Mike,
Ah, makes sense.
For the time being I'll stick with controlling the clock frequency with Linux.
Thank... Kim Nielsen

03/29/2023

07:03 PM Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim,
I think the reason why the uBoot Critical Link publishes is using 300 MHz is because the Revision 1 silico... Michael Williamson

03/27/2023

02:12 PM Software Development: RE: Increasing CPU clock OMAPL138

Alright.
Is there is no way to change the default frequency from 300Mhz to e.g. 372MHz with U-Boot?
As far as I ... Kim Nielsen

02:01 PM Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim,
I think the issue is that the voltage scaling needs to be done to default
to a higher frequency.
The P... Michael Williamson

02:00 PM Software Development: RE: Increasing CPU clock OMAPL138

I don't see an obvious default frequency config in the kernel, I'd guess that it stays with whatever frequency was se... Jonathan Cormier

01:44 PM Software Development: RE: Increasing CPU clock OMAPL138

I actually got another question.
By default, the cpu frequency seems to always be 300 MHz.
Is this value hardco... Kim Nielsen

03/24/2023

05:24 PM Software Development: RE: Increasing CPU clock OMAPL138

Kim Nielsen wrote in message#6283:
> It's our own "experimental" kernel.
> It seems to be working now. The issue wa... Jonathan Cormier

12:21 PM Software Development: RE: Increasing CPU clock OMAPL138

It's our own "experimental" kernel.
It seems to be working now. The issue was that the pll0 registers were apparentl... Kim Nielsen

03/23/2023

01:37 PM Software Development: RE: Increasing CPU clock OMAPL138

Where is the 4.19 kernel based from? It doesn't appear to have working cpufreq. Jonathan Cormier

07:17 AM Software Development: RE: Increasing CPU clock OMAPL138

Hi Mike & Jonathan,
Thank you for the fast reply :-)
I have the following frequencies available according to th... Kim Nielsen

03/22/2023

09:25 PM Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim, What kernel version are you using? Testing this on our released 3.2 kernel appears to be working for me.
... Jonathan Cormier

05:23 PM Software Development: RE: Increasing CPU clock OMAPL138

Hi Kim,
What do you get when you dump out the scaling_available_frequencies (I don't remember the exact name off t... Michael Williamson

03:14 PM Software Development: Increasing CPU clock OMAPL138

Hi,
I'm using a "L138-FI-236-RL" SOM board with SYS/BIOS running on the DSP and Linux on the ARM.
The Linux is bu... Kim Nielsen