Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)

Hi,

I have problems connecting to the industial IO/AM1808 card using device USB. I have built the kernel and the ethernet gadget module from git (3.2.x) - the module loads without any errors - I do get a usb0 network device right away. However, when I connect to a XP computer with a usb cable, nothing happens. At this moment I would have expected a driver request to pop up on the PC screen. It almost look like the usb phy is not attatched to the connector, but I cannot see that I have to set any special configuration in u-boot to enable the usb port. The host interface (usb1) is working correctly. Loading the mass storage gadget driver I experience the same problem - no connection to the PC. I have listed some output from my kernel below for recerence. Any suggestion about what to do next?

Inserting the ethernet gadget module:

>insmod g_ether.ko
gadget: using random self ethernet address
gadget: using random host ethernet address
usb0: MAC 3e:71:5d:e6:8a:2a
usb0: HOST MAC 6a:f1:01:f0:2e:1a
gadget: Ethernet Gadget, version: Memorial Day 2008
gadget: g_ether ready
musb-hdrc musb-hdrc: MUSB HDRC host driver
musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ADDRCONF: usb0: link is not ready

The automatically created network interface:

>ifconfig usb0
usb0 Link encap:Ethernet HWaddr 3E:71:5D:E6:8A:2A
inet addr:192.168.7.2 Bcast:192.168.7.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

From /proc/driver/rndis-000

root@vdr:/proc/driver# cat rndis-000
Config Nr. 0
used : y
state : RNDIS_UNINITIALIZED
medium : 0x00000000
speed : 0
cable : disconnected
vendor ID : 0x00000000
vendor : (null)

From /sys/kernel/debug/usb/devices

root@vdr:/sys/kernel/debug/usb# cat devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.02
S: Manufacturer=Linux 3.2.0+ musb-hcd
S: Product=MUSB HDRC host driver
S: SerialNumber=musb-hdrc
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 1
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.02
S: Manufacturer=Linux 3.2.0+ ohci_hcd
S: Product=DA8xx OHCI
S: SerialNumber=ohci.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms