Activity
From 03/15/2013 to 04/13/2013
04/11/2013
- 01:57 PM Software Development: RE: SATA not recognized
- I don't think you will need to rebuild DSPLINK or CMEM.
You should be able to take the myconfig and copy it to the... - 01:36 PM Software Development: RE: SATA not recognized
- What's the best way to do that and change only that one feature?
I generated a config file from my kernel with the... - 11:54 AM Software Development: RE: SATA not recognized
- You need SATA_AHCI_PLATFORM set. You will need to rebuild the kernel.
-Mike
- 11:42 AM Software Development: RE: SATA not recognized
- Here's the result:...
- 11:36 AM Software Development: RE: SATA not recognized
- Mary,
You can print the kernel config file by running:
_zcat /proc/config.gz _
You can then search the outpu... - 11:24 AM Software Development: RE: SATA not recognized
- My colleague has another SATA drive and MityDSP board. He reports as follows:
"The drive comes up fine in Windows... - 10:51 AM Software Development: RE: SATA not recognized
- Mary,
There should be no reason that the drive isn't detected by Windows XP when using a USB to Sata adapter. Ass... - 09:20 AM Software Development: RE: SATA not recognized
- I have tried the same SATA drive on a second MityDSP board as well as an older SATA drive. There are no "ata" messag...
04/10/2013
- Hi,
I've followed the instructions on http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Install...
04/09/2013
- 02:02 PM Software Development: RE: GPIO interrupt in MityOMAP-L138F
- Hi Mike,
thanks for fast reply!
The best would be an example using an fpga gpio pin and an omap pin, just to tes...
04/08/2013
- 01:07 PM Software Development: RE: GPIO interrupt in MityOMAP-L138F
- Are you trying to use a FPGA GPIO or an OMAP-L138 GPIO?
The DspGpio.h class should provide access to the OMAP-L138... - Hello all,
I need to hook a HWI to a GPIO pin in a DSP application.
I have some questions:
1- Do your core libra... - 12:49 PM Software Development: RE: L138 - DSP Timer interrupt question ...
- Mike,
Thanks for information. Always very intressting. I am reading the Day2_AM training document.
Here our cu... - Hello,
I am using Virtual Box and MityDSP-L138_SDK_2012_06_13.eva image.
When I following Start Guide instruction ...
04/07/2013
- 07:53 AM Software Development: RE: L138 - DSP Timer interrupt question ...
- Check the "Interrupt Handling - Delayed Branch Latency" section of the Day2_AM training presentation located in our "...
04/04/2013
- 04:27 PM Software Development: RE: L138 - DSP Timer interrupt question ...
- Mike,
Can you add more details regarding this statement: _The DSP loop optimization can create large interrupt lat... - 11:43 AM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
- Also feel free to look through the wiki http://support.criticallink.com/redmine/projects/arm9-platforms/wiki
- 11:40 AM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
- The username for the modules should be _root_
04/03/2013
- 10:16 PM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
- Hi,
Thank you so much for supporting.
For (1): At the first time. Now the board are running with null modem cable... - 07:17 AM Software Development: RE: MityDSP-L138F Failure to Boot and Cannot Reset
- I am assuming these are out of the box Development kits?
For (1) the console UART, please ensure you are using the... - 08:27 AM PCB Development: RE: Resistors in EMA signal and adress traces?
- Mike,
it's the L138-FX-225-RC Module. No FPGA.
I'm concerned about both kinds of traces.
Christian - 07:33 AM PCB Development: RE: Resistors in EMA signal and adress traces?
- Which part number? Specifically, does the module include an FPGA or not?
Which EMA traces are you concerned with,... - Hi,
can anybody tell me if there are already resistors on the EMA-traces on the L138-Modul integrated? If yes, wha...
04/02/2013
- Hello
I am using Industrial I/O board(80-000268RI-2 A) and 2 L138 board (L138-CG-225-RC ,L138-FG-225-RC).I got 2 i...
03/28/2013
- Trying to install an intel 330 series SSD (60 Gb). I have a power brick for it and plugged that in. Connected to th...
03/26/2013
- 11:48 AM Software Development: RE: SPI NOR Flash memory map
- You are correct, Mike. The flash does have to be erased before writing. Here is a more fleshed out version of my cod...
- 11:13 AM Software Development: RE: SPI NOR Flash memory map
- BTW:
It's not entirely clear to me if the write routine above will work properly. I don't know for sure, off-hand... - 11:11 AM Software Development: RE: SPI NOR Flash memory map
- The SPI partitions are defaulted in the board-mityomapl138.c file in arch/arm/mach-davinci in the spi_flash_partition...
- 10:55 AM Software Development: RE: SPI NOR Flash memory map
- Please allow me to chime in with a similar question... I have "reorganized" the upper part of the spi nor flash on my...
03/22/2013
- 03:13 PM Software Development: RE: Creating a Read-Only Filesystem
- I worked on it some more and ended up with a script with seven patch files that change it to a read-only filesystem. ...
- 01:01 PM FPGA Development: RE: L138F - FPGA gets incorrect data from UPP
- Marek,
The UPP clocks may be sourced by either the FPGA or the OMAP-L138 based on your configuration requirements.... - Hello,
I have problem when trying to read data on UPP by FPGA (sent from OMAP - working with L138F, XC6SLX45, ISE ...
03/20/2013
- 09:16 AM Software Development: RE: Creating a Read-Only Filesystem
- Jim,
Any luck? As far as I can tell that mount entry should work.
03/15/2013
- 11:32 AM Software Development: RE: MDK_2012-08-10 default configuration
- Mike,
Thanks for pointing that out - really helpful!
I can most definitely see the network (and boot from it) from ...
Also available in: Atom
Go to top
