Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)

03/10/2015

05:04 PM FPGA Development: RE: FPGA serial programming interface

I understand that. However, I would like to configure the FPGA in serial slave mode. stephan berner

05:01 PM FPGA Development: RE: FPGA serial programming interface

SB,
The FPGA is configured using 8 bit parallel slave select mode via the EMIFA bus connection to the Omap L138 pr... Alexander Block

03:36 PM FPGA Development: FPGA serial programming interface

hi,
are the pins CCLK, DIN and the MODE pins available on the OMAP-138 as GPIOs, or are they open/hardcoded on the... stephan berner

03/05/2015

05:20 PM Software Development: RE: Write to SharedMem from DSP and read it from ARM

Thanks for the cache info. Completely missed that part.
I reverted to the original code, and I've added BCACHE_wb(... Frank C

02/19/2015

10:48 AM Software Development: RE: MDK_2012-08-10 default configuration

There also may be a small time penalty in having the kernel search for the phy. But this would need to be quantified ... Jonathan Cormier

10:46 AM Software Development: RE: MDK_2012-08-10 default configuration

I believe the phy address was set in an earlier version of the kernel and it was carried forward. There is also the ... Jonathan Cormier

09:52 AM Software Development: RE: MDK_2012-08-10 default configuration

Thanks Mike for answer.
I did not look at section 2.2 of TLK100PHP datasheet. It is my fault.
I read section "3... François Tremblay

09:18 AM Software Development: RE: MDK_2012-08-10 default configuration

Hi François,
In the datasheet for the TLK100PHP, Section 2.2 shows that the PHYAD0 pin has an internal pull-up, wh... Michael Williamson

07:33 AM Software Development: RE: MDK_2012-08-10 default configuration

I look at U-boot code and it doesn't explain what we are seeing.
When resetting the PHY device, only GPIO5[15] is ... François Tremblay

02/18/2015

04:59 PM Software Development: RE: MDK_2012-08-10 default configuration

Thanks Jonathan to told me that I am not alone with that questioning.
The first revision of our custom board had a... François Tremblay

04:43 PM Software Development: RE: MDK_2012-08-10 default configuration

François,
I too was confused about this but was unable to determine why the phy id becomes 0x03.
I checked th... Jonathan Cormier

04:21 PM Software Development: RE: MDK_2012-08-10 default configuration

Mike,
My reply is out of date but it is about that topic: PHY address configuration.
You said that PHY address ... François Tremblay

03:59 PM Software Development: RE: Write to SharedMem from DSP and read it from ARM

Pretty sure you have to flush the DSP cache after changing values. Jonathan Cormier

03:48 PM Software Development: RE: Write to SharedMem from DSP and read it from ARM

Hi,
I am trying to get the shared memory working as well (by writing from DSP side and reading back from ARM side)... Frank C

02/17/2015

11:41 AM Software Development: RE: Alter Ethernet MAC

Thanks Jonathan, that's exactly what I was after. Mostafa Afgani

11:41 AM Software Development: RE: Alter Ethernet MAC

You might also try this technique, though I am not sure if the current version of the 3.2 kernel has this command lin... Michael Williamson

11:26 AM Software Development: RE: Alter Ethernet MAC

Mostafa,
We store the mac address on a eeprom on the SoM. The settings stored on this can be accessed using the f... Jonathan Cormier

11:01 AM Software Development: Alter Ethernet MAC

Hi, is it possible to alter the 'burned-in' MAC address of an L138F? I know that I can change it using 'ifconfig eth0... Mostafa Afgani