Activity
From 05/20/2018 to 06/18/2018
06/04/2018
- 03:41 PM Software Development: RE: xmlrpc libs for application
- ok, that may be the path of least resistance at this point, thanks for the quick response, Regs, Tom
- 03:31 PM Software Development: RE: xmlrpc libs for application
- I'm not sure the opkg-target command works or exists anymore. You could with some effort, install the curl libraries...
- 03:21 PM Software Development: RE: xmlrpc libs for application
- Hi Bob,
So I first took a shot at building xmlrpc with the Angstrom 2012.5 rootfs. Have pulled a version of the co... - 02:19 PM Software Development: RE: xmlrpc libs for application
- Tom Riddle wrote:
> Hi,
>
>
> I cannot find "opkg-target" anywhere in the MDK 2014, or on the host machine.
... - 01:15 PM Software Development: RE: xmlrpc libs for application
- Hi,
Hope someone can assist with the following questions. I need to install some packages on the host build system...
06/02/2018
- 01:00 PM Software Development: RE: xmlrpc libs for application
- Hi Jonathan, Thanks for the status. Yea I poked around and couldn't readily find links to sources either. I will take...
06/01/2018
- 05:31 PM Software Development: RE: xmlrpc libs for application
- Tom, the open embedded instructions are unlikely to work. They are at least 6 years out of date and I believe most of...
- 04:51 PM Software Development: RE: xmlrpc libs for application
- Hi Bob, So the link Jonathan posted was helpful with our task of building xmlrpc from source. However I am a bit conf...
05/31/2018
- 03:39 PM Software Development: RE: xmlrpc libs for application
- Hi Tom, I'm not sure I entirely understand what you are trying to accomplish, but let me start with giving you a few ...
- 03:12 PM Software Development: RE: xmlrpc libs for application
- Some additional detail, have been using the Jan-2014 based MDK for the kernel work to this point, however it doesn't ...
- 11:37 AM Software Development: RE: xmlrpc libs for application
- Hi, I was looking for opkg-target which is part of the MDK, where would it be? BTW, I am not using the VM on Windows ...
05/30/2018
- 11:33 PM Software Development: RE: xmlrpc libs for application
- Hi Jonathan, Thanks that's going to get me started. Regs, Tom
- 09:54 PM Software Development: RE: xmlrpc libs for application
- Looks like the library supports autotools and configure. Check out this link: https://support.criticallink.com/redmi...
- Hi, We have a need to build one of our custom C based apps for the MityDSP L138. It requires libxmlrpc_server and lib...
05/23/2018
- 02:24 PM PCB Development: RE: New Design Bringup Question
- Thank you for the update! Happy to hear all is working now.
Alex - 03:55 AM PCB Development: RE: New Design Bringup Question
- Hi Alex, here's an update, checked for BOOTME and actually do see that output on the serial port, so the processor is...
05/22/2018
- 11:12 PM PCB Development: RE: New Design Bringup Question
- Hi Alex, a few more details that may be helpful to know. The TI ADC eval board (we used before our board showed up) c...
- 09:06 PM PCB Development: RE: New Design Bringup Question
- Hi Alex, Thanks again... I'll be able to scope the SPI signals shortly.
So in our design we have an ADC with SPI ... - 06:11 PM PCB Development: RE: New Design Bringup Question
- Tom,
Can you comment on J700 concerning the "where" used for +3.3V, SCLK, SIMO and SOMI? I see U901 mentioned for ... - 05:47 PM PCB Development: RE: New Design Bringup Question
- Tom Riddle wrote:
> Hi Alex,
>
> Thanks, I will get a chance to check the boot sequence is a bit. Now I do not h... - 05:34 PM PCB Development: RE: New Design Bringup Question
- Hi Alex,
Thanks, I will get a chance to check the boot sequence is a bit. Now I do not have anything on J700 Pin ... - 04:48 PM PCB Development: RE: New Design Bringup Question
- Tom,
Sorry for the delay in getting back to you on this issue.
The first step you can take is to see if the Mit...
05/21/2018
- 03:56 PM FPGA Development: RE: FPGA GPIO issue
- Okay thanks Tom. I put that link in the wiki page to hopefully help people in the future.
Also available in: Atom
Go to top