Activity
From 04/30/2015 to 05/29/2015
05/29/2015
- 07:27 AM Software Development: RE: PHY not working with QSPI flash boot
- Hi Mike,
Thanks for all the support. I've managed to solve the problem by downloading the 5CSX Project once again,... - 06:53 AM Software Development: RE: PHY not working with QSPI flash boot
- I am checking with our hardware guy here but I don't think the MPU rate is altered by the BOOTSEL pins after u-Boot.
... - 03:31 AM FPGA Development: RE: HSMC1 pinout
- Alex,
thank you for clearing that up!
B) Just for the record, SMC1_SMSDA should be SoM pin 54 and HSMC1_SMSCL s...
05/28/2015
- 11:32 AM Software Development: RE: PHY not working with QSPI flash boot
- Hi Mike,
I have tested it with the image that is available here: http://support.criticallink.com/files/mitysom-5cs... - 10:19 AM Software Development: RE: PHY not working with QSPI flash boot
- Hi,
We are not aware of any problem until your post. We had tried to reproduces this problem after you originally ... - 10:01 AM Software Development: RE: PHY not working with QSPI flash boot
- I just want to report that this problem is _not_ present when using an Altera Cyclone V DevKit.
I have no problem w... - 09:00 AM Software Development: RE: PHY not working with QSPI flash boot
- Hi Mike,
Thanks for replying. The U-Boot environments are identical. The driver should also be there as I have jus... - 07:28 AM Software Development: RE: PHY not working with QSPI flash boot
- Sorry,
The only thing that comes to mind is if somehow the uBoot environment has changed or the SPL build removed ... - 06:08 AM Software Development: RE: PHY not working with QSPI flash boot
- Any ideas of what the problem might be?
Can somebody at least reproduce this behavior?
- 11:08 AM FPGA Development: RE: HSMC1 pinout
- Floria,
A) We confirmed that the .tcl script is in fact incorrect for that pin-assignment.
Correct pin assignme... - 04:30 AM Software Development: RE: PCI-e Intel - System crash
- It's a total freeze, no dumps are written. Guess the only option is to use the DS-5 Kernel/Device Drivers debug capab...
05/27/2015
- 09:38 AM Software Development: RE: PCI-e Intel - System crash
- I don't seem to get any oops or panic, it just hangs. I'm attaching the output of dmesg up to the point where the sys...
- 08:36 AM Software Development: RE: PCI-e Intel - System crash
- Can you dump out the kernel messages (oops? panic? dmesg?)?
-Mike
- Hello,
I am trying to get the PCI-e interface on the MitySoM DevKit (RC-3C version) to work with an Intel 82574L G...
05/26/2015
- Hi,
I am using the "mityarm_5csx_dev_board_hsmc_setup.tcl":https://support.criticallink.com/redmine/boards/47/topi...
05/20/2015
- Hi,
I am trying to set up the MitySOM such that U-Boot is stored on the flash memory and the Linux Kernel, DTS and...
05/19/2015
- 03:30 AM Software Development: RE: Boot configuration jumpers
- Thank you very much. As I've seen the labeling is to the right of the switch (in my case), hence I didn't pay attenti...
05/18/2015
- 11:30 AM Software Development: RE: Boot configuration jumpers
- Sorry this isn't clear. There is silkscreen labeling below the switch corresponding to the switch locations 1-10: MS...
- Hi,
Can someone please shed me some light on the boot configuration jumpers of the MitySOM-5CSX Dev-Kit? On the da...
04/30/2015
- 07:53 AM Software Development: RE: Bare-metal interrupt handling working only in debugger
- Hi Alex,
Glad you solved your issue, sorry we didn't provide much help. We don't have a lot of folks trying to do... - 06:22 AM Software Development: RE: Bare-metal interrupt handling working only in debugger
- No, that was obviously not the reason. The unhosted and hosted linker scripts do link against different libraries but...
Also available in: Atom
Go to top
