Activity

From 06/15/2016 to 07/14/2016

09:02 AM Software Development: RE: SPI1 controller, access to FLASH and carrier board. NOT linux based.: Excellent glad you got it working. Jonathan Cormier
12:16 AM Software Development: RE: SPI1 controller, access to FLASH and carrier board. NOT linux based.: Johnathan,
Joy Joy, Happy Happy.
Everything is working. There were three items altogether. First was the "open... Ian St. John

05:06 PM Software Development: RE: L138 dsplink problem - schedule while atomic bug: I looked deeper into the error we were provoking on our bench; it turned out to be a c++ vector de-referencing error ... Fred Weiser

06:24 PM Software Development: RE: SPI1 controller, access to FLASH and carrier board. NOT linux based.: Ian St. John wrote:
> Can you confirm that the signal marked as 'reserved' just beside the SPI1_CSC1 is the SPI1_CSC... Jonathan Cormier
05:56 PM Software Development: RE: SPI1 controller, access to FLASH and carrier board. NOT linux based.: Hmm. I asked the EE about the diagram and he was interested in the fact that there was a pull up on the CS line. Appa... Ian St. John
12:40 AM Software Development: RE: SPI1 controller, access to FLASH and carrier board. NOT linux based.: The eeprom is on the i2c0 bus. I'm assuming you are talking about the SPI Nor flash which is on SPI1_CS0.+
Oops... Ian St. John
01:23 PM Software Development: RE: L138 dsplink problem - schedule while atomic bug: Hi Fred,
Syslink is newer than DSPlink, though in the context of the L138 it's very similar code (syslink evolved ... Michael Williamson
12:11 PM Software Development: RE: L138 dsplink problem - schedule while atomic bug: The error collected above was on the bench after making some minor software changes seemingly unrelated with the code... Fred Weiser
11:23 AM Software Development: RE: L138 dsplink problem - schedule while atomic bug: I found the following on the TI site; looks like they struggled with this issue with sys-link... I'm not sure how sys... Fred Weiser

11:55 AM Software Development: L138 dsplink problem - schedule while atomic bug: I think there may be a bug in the dsplink kernel code that causes the scheduler to run after a call to spinlock. "rem... Fred Weiser
09:33 AM Software Development: RE: SPI1 controller, access to FLASH and carrier board. NOT linux based.: Ian St. John wrote:
> I am building and programming a custom board without Linux. Basic embedded drivers running fro... Jonathan Cormier

10:18 AM Software Development: SPI1 controller, access to FLASH and carrier board. NOT linux based.: I am building and programming a custom board without Linux. Basic embedded drivers running from SPI1,CS0 (8MB NOR Fla... Ian St. John

04:13 AM Software Development: RE: kernel 3.2 - tcpip stack latency: Hi Greg,
Than you for your feedback.
Indeed, flag CONFIG_PREEMPT is set in kernel config. As far as we can see... Patrice Bastiaens

01:30 PM Software Development: RE: kernel 3.2 - tcpip stack latency: Hi Patrice,
Since you are using SCHED_RR I am assuming you are using CONFIG_PREEMPT in your kernel config, correc... Gregory Gluszek
06:26 AM Software Development: kernel 3.2 - tcpip stack latency: Hello,
We've built an application receiving messages from two devices at a rate of 1 message of 1440 bytes every 1... Patrice Bastiaens

08:25 AM Software Development: RE: Flashing a new kernel to NOR from Linux rather than u-boot: Here are the results from my board/MDK:... Fred Weiser

05:43 PM Software Development: RE: Flashing a new kernel to NOR from Linux rather than u-boot: Alternatively it may be possible for you to build the kernel features as modules and insert them in the live system. ... Jonathan Cormier
05:39 PM Software Development: RE: Flashing a new kernel to NOR from Linux rather than u-boot: Fred,
Do you have /dev/mtdblock* devices? My kernel boot args have this "root=/dev/mtdblock0", so my assumption i... Jonathan Cormier
05:26 PM Software Development: Flashing a new kernel to NOR from Linux rather than u-boot: We use opkg to push updates to our products that are installed in the field. We now need a way to update the kernel, ... Fred Weiser

05:14 PM Software Development: RE: How to configure the GPIOs as outputs?: Do note that the custom baseboard instructions were written for the 335x family. So some things will be slightly diff... Jonathan Cormier
04:14 PM Software Development: RE: How to configure the GPIOs as outputs?: Héctor,
Please check the last section of this page for information on how to review and set the pinmux for the dev... Bob Duke
03:11 PM Software Development: How to configure the GPIOs as outputs?: Hi, it's me again,
I'm knowing the Profibus Development Kit (and embedded systems) and for that I'm trying to do s... Hector Bojorquez
11:00 AM Software Development: RE: Problems with the first time configuration: Now it's working, thanks a lot Jonathan! Hector Bojorquez
10:02 AM Software Development: RE: Problems with the first time configuration: Hector Bojorquez wrote:
> > This is a error is normal and doesn't hurt anything.
> *
> So, the reflashing process ... Jonathan Cormier
09:55 AM Software Development: RE: Problems with the first time configuration: > This is a error is normal and doesn't hurt anything.
*
So, the reflashing process went well?*
> If you don't h... Hector Bojorquez
08:38 AM Software Development: RE: Problems with the first time configuration: Hector Bojorquez wrote:
> >There shouldn't be a space in the console arg. "console=ttyS1,115200n8"
> >Also root sh... Jonathan Cormier

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)