Project

General

Profile

Activity

From 05/09/2012 to 06/07/2012

06/05/2012

03:06 PM Software Development: RE: Flashing NAND from SD Card
Hi,
Do we have any update on the u-boot MLO?
Appreciate your response.
Thanks
Raja.
Raja Vankam

05/31/2012

12:54 PM Software Development: RE: Connecting JTAG to Mityarm board
Raja,
A couple of thoughts come to mind:
1) If your volume is high enough, Critical Link may be able to pre-pro...
Michael Williamson
12:16 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Michael,
Thanks for your reply.
I will try with the tera term script file.
We have just SD card available...
Raja Vankam
11:01 AM Software Development: RE: Connecting JTAG to Mityarm board
Another note:
Do you have any other I/O connections for storage such as MMC or USB Host (sticks)? If so you could...
Michael Williamson
10:33 AM Software Development: RE: Connecting JTAG to Mityarm board
Raja
This TI page talks about various ways to flash the NAND (from CCS, etc)
http://processors.wiki.ti.com/index.ph...
Tim Iskander

05/30/2012

05:37 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Alex,
I have also referred the same link provided by you (http://processors.wiki.ti.com/index.php/Linux_Debug_i...
Raja Vankam
05:21 PM Software Development: RE: Connecting JTAG to Mityarm board
Raja,
Typically we load the kernel over either tftp/nfs and write it onto the MityARM-3359 flash memory or boot fr...
Alexander Block
03:46 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Alex,
Do we have any inputs on connecting JTAG to Mityarm board and can be used for flashing?
Alternatively ...
Raja Vankam
01:21 PM Software Development: RE: Flashing NAND from SD Card
Hi Tim,
Thanks. I will wait for your response.
Regards,
Raja.
Raja Vankam
01:19 PM Software Development: RE: Flashing NAND from SD Card
Raja
I am looking in to this... I am suspecting that the u-boot MLO was not configured correctly for the nand flash ...
Tim Iskander
01:18 PM Software Development: RE: Flashing NAND from SD Card
Hi,
Do we have any answer on this.
Thanks,
Raja.
Raja Vankam

05/29/2012

03:21 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Alex,
I am working on to connect the JTAG to the mityarm board.
But having trouble how to proceed with proje...
Raja Vankam
09:58 AM Software Development: RE: Flashing NAND from SD Card
Hi Tim,
I have programmed as per the address mentioned above.
But during booting MLO always looks for u-boot a...
Raja Vankam

05/24/2012

01:33 PM Software Development: RE: Flashing NAND from SD Card
Raja
The MTD partitions set up in the kernel are also the positions uboot expects
things to be in
Creating 8 MTD p...
Tim Iskander
11:47 AM Software Development: RE: Flashing NAND from SD Card
Hi,
I could load bootloader to NAND and my boot log is as below. Flashed MLO at 0x0 and u-boot.img at 0x40000. u-b...
Raja Vankam

05/21/2012

06:06 PM Software Development: RE: Flashing NAND from SD Card
Hi Tim,
Do we have any answer on this.
I found one thing interesting from booting sequence of the board.
Below...
Raja Vankam
11:05 AM Software Development: RE: Usage of I2C1 to connect external peripheral
The error you are seeing is from the I2C device not seeing the proper ACK response from the I2C slave device when it ... Michael Williamson
10:57 AM Software Development: RE: Usage of I2C1 to connect external peripheral
Hi Mike,
I am coming back to you after long time. we have created setup with the slave connected on mityarm.
At...
Raja Vankam

05/18/2012

12:14 PM Software Development: RE: Flashing NAND from SD Card
Hi Tim,
I have flashed as mentioned above.
But even now u-boot prompt is not appearing after booting from NAND.
...
Raja Vankam
10:42 AM Software Development: RE: Flashing NAND from SD Card
Raja
Your uboot image is 373252 bytes long
you are only erasing/writing 0x40000, which is 262144 (256k)
try erasin...
Tim Iskander
10:08 AM Software Development: RE: Flashing NAND from SD Card
Hi Tim,
I have followed your instructions and flashed NAND with MLO at 0x20000 and u-boot.img at 0x40000. but the ...
Raja Vankam

05/17/2012

09:54 PM Software Development: RE: Connecting JTAG to Mityarm board
Raja,
Sorry about the delay but I did want to update the fact that I was able to have the debugger connect to my M...
Alexander Block
06:01 PM Software Development: RE: Flashing NAND from SD Card
Raja
The uboot spl (MLO) loads from nand at 0x00040000...
nand_spl_load_image: loading 2048 bytes from *0x00040000...
Tim Iskander
04:52 PM Software Development: Flashing NAND from SD Card
Hi,
1. I have tried flashing NAND through SD boot. I have followed the steps mentioned in AM335x u-boot users guid...
Raja Vankam

05/16/2012

05:42 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Alex,
Thanks for your reply.
I will try with these files.
What are the sys-boot options i have to set whi...
Raja Vankam
02:11 PM Software Development: RE: Connecting JTAG to Mityarm board
Hello Raja,
Attached are both a gel file and a ccxml file that hopefully will get you going. The gel file has been...
Alexander Block
01:21 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Raja -
Sorry for the delay in getting back to you on this. We are working this now and will have an answer for...
Thomas Catalino
11:53 AM Software Development: RE: Connecting JTAG to Mityarm board
Hi,
Do we have some inputs on this topic please?
Thanks,
Raja.
Raja Vankam

05/11/2012

12:23 PM Software Development: RE: Connecting JTAG to Mityarm board
Hi Mike,
Yes, I am connecting to MityARM-3359 and not on TI eval board.
So i want to know what .gel file i need...
Raja Vankam
10:43 AM Software Development: RE: Connecting JTAG to Mityarm board
Hi Raja,
Were you successful when you tried connecting the JTAG to the TI eval board?
I am assuming you are c...
Michael Williamson
10:23 AM Software Development: Connecting JTAG to Mityarm board
Hi,
I have tried connecting JTAG XDS100V2 to the Mityarm evaluation board. Changed the boot options to give first ...
Raja Vankam
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)