Activity

From 08/28/2012 to 09/26/2012

10:10 AM PCB Development: RE: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector: We have not tested such a configuration, so I don't really know. If the electrical connections honor the spec, then ... Michael Williamson

03:12 PM PCB Development: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector: The MityARM design guide suggests an SO-DIMM connector with a standard keying. We have built our board with a revers... Ali Asgar Sohanghpurwala

10:11 AM Software Development: RE: MityARM-335x Ethernet Communication: Found the problem. The problem was related to the errata on the Vitesse VSC8601 Ethernet phy used on the development... Anonymous

09:49 AM Software Development: MityARM-335x Ethernet Communication: I am trying to get the TI StarterWare Enet_Echo example to run on the MityARM-335x Development Kit. To accomplish thi... Anonymous

04:36 PM Software Development: RE: mod_fastcgi.so: Hi Scott,
Tried that with no luck...
however I was looking through the lighttpd documentation and saw I forgot t... R D
02:45 PM Software Development: RE: mod_fastcgi.so: Try "--host=arm-angstrom-linux-gnueabi" instead....
-Mike
Michael Williamson
02:30 PM Software Development: RE: mod_fastcgi.so: Scott,
Downloaded from:
http://download.lighttpd.net/lighttpd/releases-1.4.x/
lighttpd-1.4.26.tar.gz 2010-Feb-07... R D
12:38 PM Software Development: RE: mod_fastcgi.so: Randy,
Could you give me a link to where you downloaded the lighttpd source? Also once you downloaded it, can you ... Scott Gerenser
09:41 AM Software Development: RE: mod_fastcgi.so: Hi Mike,
I found out the version of the lighttpd based on one of the included shared libraries.
I have downloaded... R D

10:57 AM Software Development: RE: mod_fastcgi.so: Hi Mike,
Should have mentioned Linux and Lighttpd are very new for me.
I had assumed I could just compile the light... R D

06:36 AM Software Development: RE: mod_fastcgi.so: So anyway, the mod-fastcgi.so should not require you to rebuild the kernel. You should be able to download it, "conf... Michael Williamson

12:54 PM Software Development: RE: mod_fastcgi.so: What filesystem are you using? You might be able to get it installed using opkg.
-Mike
Michael Williamson
12:14 PM Software Development: mod_fastcgi.so: Hi,
I'm trying to use fastcgi with the lighttpd web server. I have successfully create a simple example and changed ... R D

12:29 AM Software Development: RE: Re-assigning the PHY_RESET: Hi Tim,
Thanks for you quick reply. I managed to swap the PHY_RESET and get the Ethernet working - Brilliant!.
Than... Keith Fletcher

10:01 AM Software Development: RE: Re-assigning the PHY_RESET: Keith
The pinmux setup for the PHY reset should be done in u-boot. It is in board/cl/mityarm335x/mux.c in the rgmii2... Tim Iskander

10:33 PM Software Development: Re-assigning the PHY_RESET: Hi,
I want to re-assign the PHY_RESET from gpio3_10 to gpio3_4. I can have included gpio3_4 in mux33xx.c but it ap... Keith Fletcher

10:48 AM Software Development: Booting StarterWare on MityARM-335x: (posted on behalf of a customer)
We would like to use a simple TI StarterWare based design possibly with SYSBIOS.... Thomas Catalino

01:29 PM PCB Development: RE: MityARM-335x I2C1_SDA and I2C1_SCL Pull-up Resistors: Hi Mike,
Thanks for clarifying how the I2C buses are implemented on the module.
There is no problem, I was uncl... Joel Minski
10:25 AM Software Development: RE: Boot from NAND?: The MityARM-3359 is capable of booting from NAND. See wiki page http://support.criticallink.com/redmine/projects/armc... Tim Iskander
10:19 AM Software Development: Boot from NAND?: (posted for a customer)
Can the MityARM-3359 boot from NAND? Thomas Catalino

Also available in: Atom

Go to top

Mity CPU Platforms » MitySOM-335x (ARM Cortex-A8 Based Products)