Mity CPU Platforms » MitySOM-5CSX Altera Cyclone V

05/29/2015

07:27 AM Software Development: RE: PHY not working with QSPI flash boot

Hi Mike,
Thanks for all the support. I've managed to solve the problem by downloading the 5CSX Project once again,... Alexandre Lopes

06:53 AM Software Development: RE: PHY not working with QSPI flash boot

I am checking with our hardware guy here but I don't think the MPU rate is altered by the BOOTSEL pins after u-Boot.
... Michael Williamson

03:31 AM FPGA Development: RE: HSMC1 pinout

Alex,
thank you for clearing that up!
B) Just for the record, SMC1_SMSDA should be SoM pin 54 and HSMC1_SMSCL s... Florian Rieger

05/28/2015

11:32 AM Software Development: RE: PHY not working with QSPI flash boot

Hi Mike,
I have tested it with the image that is available here: http://support.criticallink.com/files/mitysom-5cs... Alexandre Lopes

10:19 AM Software Development: RE: PHY not working with QSPI flash boot

Hi,
We are not aware of any problem until your post. We had tried to reproduces this problem after you originally ... Michael Williamson

10:01 AM Software Development: RE: PHY not working with QSPI flash boot

I just want to report that this problem is _not_ present when using an Altera Cyclone V DevKit.
I have no problem w... Alexandre Lopes

09:00 AM Software Development: RE: PHY not working with QSPI flash boot

Hi Mike,
Thanks for replying. The U-Boot environments are identical. The driver should also be there as I have jus... Alexandre Lopes

07:28 AM Software Development: RE: PHY not working with QSPI flash boot

Sorry,
The only thing that comes to mind is if somehow the uBoot environment has changed or the SPL build removed ... Michael Williamson

06:08 AM Software Development: RE: PHY not working with QSPI flash boot

Any ideas of what the problem might be?
Can somebody at least reproduce this behavior?
Alexandre Lopes

11:08 AM FPGA Development: RE: HSMC1 pinout

Floria,
A) We confirmed that the .tcl script is in fact incorrect for that pin-assignment.
Correct pin assignme... Alexander Block

04:30 AM Software Development: RE: PCI-e Intel - System crash

It's a total freeze, no dumps are written. Guess the only option is to use the DS-5 Kernel/Device Drivers debug capab... Alexandre Lopes

05/27/2015

09:38 AM Software Development: RE: PCI-e Intel - System crash

I don't seem to get any oops or panic, it just hangs. I'm attaching the output of dmesg up to the point where the sys... Alexandre Lopes

08:36 AM Software Development: RE: PCI-e Intel - System crash

Can you dump out the kernel messages (oops? panic? dmesg?)?
-Mike
Michael Williamson

08:12 AM Software Development: PCI-e Intel - System crash

Hello,
I am trying to get the PCI-e interface on the MitySoM DevKit (RC-3C version) to work with an Intel 82574L G... Alexandre Lopes

05/26/2015

03:54 AM FPGA Development: HSMC1 pinout

Hi,
I am using the "mityarm_5csx_dev_board_hsmc_setup.tcl":https://support.criticallink.com/redmine/boards/47/topi... Florian Rieger

05/20/2015

08:22 AM Software Development: PHY not working with QSPI flash boot

Hi,
I am trying to set up the MitySOM such that U-Boot is stored on the flash memory and the Linux Kernel, DTS and... Alexandre Lopes

05/19/2015

03:30 AM Software Development: RE: Boot configuration jumpers

Thank you very much. As I've seen the labeling is to the right of the switch (in my case), hence I didn't pay attenti... Alexandre Lopes

05/18/2015

11:30 AM Software Development: RE: Boot configuration jumpers

Sorry this isn't clear. There is silkscreen labeling below the switch corresponding to the switch locations 1-10: MS... Adam Dziedzic

11:05 AM Software Development: Boot configuration jumpers

Hi,
Can someone please shed me some light on the boot configuration jumpers of the MitySOM-5CSX Dev-Kit? On the da... Alexandre Lopes