Activity
From 09/27/2014 to 10/26/2014
10/24/2014
- 10:41 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: L138 SOM LEDs
- Sorry,
On Non-FPGA modules:
D1 is connected to R16 (GP6_12) of the OMAP-L138.
D2 is connected to R17 (GP6_13... - 10:05 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: L138 SOM LEDs
- Hi Mike,
The SOM we are using is the non-FPGA version. What do D1 and D2 connect to?
Thanks,
Anton - 07:22 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: L138 SOM LEDs
- D1 is connected to the FPGA_DONE pin on the FPGA configuration block.
D2 is connected to P15 of the FPGA IO_L74P_A... - 10:03 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: MityDSP-L138 Boot Problem
- This issue has been resolved - we had left an uterminated SPI1_CLK signal trace on our base board at an unpopulated d...
10/22/2014
- Please can you provide information for D1 and D2 LEDs on the L138-FX-225-RC module. What are they connected to?
Tha... - We are using the L138-FX-225-RC on a new custom baseboard and are having trouble with boot:
- no UART activity in ...
10/21/2014
- 10:28 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: Communicating with an 8-bit parallel interface (GPIO, SPI or GPMC)
- SPI:
I'm not sure what you mean by using the spi bus to handle the 8-bit data bus.
If you want raw access to the ... - 10:16 AM MitySOM-335x (ARM Cortex-A8 Based Products) Software Development: RE: Communicating with an 8-bit parallel interface (GPIO, SPI or GPMC)
- As Alex mentioned the GPMC bus is used for an on-SOM nand memory. The GPMC bus allows multiple devices to use the bu...
10/20/2014
- Posting this on behalf of a customer:
The interface to their networking chip and other peripheral boards on their ... - 04:34 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Modular SGDMA
- Hi Dan,
I polling the FIFO empty signal for the both the dispatcher and write master to ensure that only when both...
10/17/2014
- 04:53 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: Modular SGDMA
- Hi Jack,
You could try polling the dispatcher's busy bit instead but I'm not quite sure if that would solve your i... - Hi
I'm running into a difficulty with the Modular SGDMA that is used in the HPS Memory example.
I have to send ...
10/02/2014
- 12:53 PM MitySOM-5CSX Altera Cyclone V FPGA Development: RE: HPS Memory Controller
- Hi,
Just raising this subject again. I'm going through the document for the sgdma_dispatcher, but do you guys have...
10/01/2014
- 02:27 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: Port 22222
- Actually, the issue seems to be with the third party software.
So don't worry about it. - 02:07 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: Port 22222
- Furthermore, ssh works to it.
We have a python program that tries to connect to the board via port 22222, but it r... - 01:58 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: Port 22222
- Hi Bob,
The only file I changed is the interface file in the /etc/network folder to give the system a static addre... - 01:44 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: Port 22222
- Jack, I'm assuming you are running the "third party software" on the PC, correct?
If so, how did you configure t... - Hi,
We are trying to have a third party software to connect to the board via Port 22222. We assigned a static addr... - 02:31 AM MitySOM-335x (ARM Cortex-A8 Based Products) PCB Development: RE: Spurious Reboot Debug
- Yes. Where do I send it?
09/30/2014
- 12:41 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: Static IP Adderess
- Hi Dan,
That works! Thank you!
Jack - 09:26 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: Static IP Adderess
- Hello Jack,
Is your PC a windows machine? If so I believe if you have the firewall on then it will block any ping ...
09/29/2014
- Hi,
I tried to set a static IP address to the system, by changing the /etc/network/interface file (See below). Bec...
Also available in: Atom
Go to top
