Project

General

Profile

Activity

From 07/31/2010 to 08/29/2010

08/27/2010

03:37 PM FPGA Development: RE: Digital DNA
Hi John,
We're still looking into this here (I wanted to at least get you some feedback that someone saw your post...
Michael Williamson

08/26/2010

12:19 PM FPGA Development: Digital DNA
Did you get a digital DNA value assigned for your FPGA's? John Mladenik

08/24/2010

09:11 PM FPGA Development: RE: POWER DOWN Memory Corruption

If your application will not be writing to the NAND flash then you should not need hold-up circuit from the motherb...
Thomas Catalino
09:04 PM FPGA Development: RE: POWER DOWN Memory Corruption
So do you think we need to put on our mother board a circuit to hold up the power and interrupt the OMAP to let it kn... John Mladenik
08:58 PM FPGA Development: RE: POWER DOWN Memory Corruption
John -
We are indeed aware of this and are working on a solution. We plan to allow for the root file system to be...
Thomas Catalino
08:37 PM FPGA Development: POWER DOWN Memory Corruption
Software guys tell me they had a case where the FLASH memory was corrupted when the power was removed at the wrong ti... John Mladenik
06:51 PM FPGA Development: RE: Programming the FPGA

Hi John.
It looks like you are generating the .BIN file using the bitgen tool ("Generate Programming File" step ...
Mike Pilawa
04:00 PM FPGA Development: RE: Programming the FPGA
Here is the .BGN but there were no .CFI or .PRM files in the FPGA directory. John Mladenik
03:44 PM FPGA Development: RE: Programming the FPGA

Hi John.
Would you be able to upload the .BGN .CFI & .PRM files that go with the .BIN file you have already uplo...
Mike Pilawa
01:37 PM FPGA Development: Programming the FPGA
We are using the MityDSP-L138. Our software guys are not able to program my FPGA bin file using your routine. Your ... John Mladenik

08/23/2010

02:34 PM Software Development: RE: Rescanning the Nand flash
Dennis,
Just so you know, the suggestions below are not based on personal experience.
Not sure there is a comma...
John Pruitt
01:48 PM Software Development: Rescanning the Nand flash
I made a type-o when loading the Nand flash. I managed to convince the flash that it has a whole bunch of bad areas. ... Dennis Volper

08/18/2010

04:16 PM Software Development: RE: Loading FPGA
Yes it is an industrial i/o board. That file did load, the light did come on. I need to tell the fpga guys they gave ... Dennis Volper
03:46 PM Software Development: RE: Loading FPGA
If you are using the Industrial I/O board Critical Link provided, try using the file attached below. This file is kn... Michael Williamson
03:35 PM Software Development: RE: Loading FPGA
Sorry about the typo-s. My email/web machine doesn't have a serial port so I've got an old laptop running the hyperte... Dennis Volper
03:16 PM Software Development: RE: Loading FPGA
On the tftp, what is the reported size of the transfer? Something like 0x71544 is expected. If the data is not the ri... John Pruitt
03:08 PM Software Development: RE: Loading FPGA
I did tftp: 0xC0700000 192.168.1.118:fpga.bin
got the ### marks
Did
loadfpga 0xC07000000
no light, message "...
Dennis Volper
02:58 PM Software Development: RE: Loading FPGA
Yes, the "done" LED should light up when the FPGA is programmed correctly.
Can you include the set of commands you...
John Pruitt
02:51 PM Software Development: RE: Loading FPGA
Should the "done" LED light up if the FPGA was programmed correctly? Dennis Volper
02:39 PM Software Development: RE: Loading FPGA
Dennis,
You are correct that the write command is missing the offset.
In the setenv command, the read is corre...
John Pruitt
02:21 PM Software Development: Loading FPGA
I've tried loading the FPGA. I didn't write the FPGA code, I'm just trying to load an fpga.bin file that I've been gi... Dennis Volper

08/09/2010

08:57 PM Software Development: RE: Kernel documentation
Interrupt number 91 (aka IRQ_DA850_RPIINT) works. It works, when I queue a DMA write I get an interrupt when it is co... Dennis Volper
08:40 PM Software Development: RE: Kernel documentation
The information you are looking for is in the "OMAP-L138 System Reference Guide":http://www.ti.com/litv/pdf/sprugm7d,... Michael Williamson
03:50 PM Software Development: RE: Kernel documentation
Building the uPP driver. I need to register and interrupt service routine.
To do that I need to know the irq number ...
Dennis Volper

08/03/2010

01:41 PM Software Development: RE: Debugging DSP side with CCS_3.3
HI Mike,
Here is my about dialog:
!cc3about.png!
When I tried to update to 3.3.82 the installer told me I didn...
Rich Bagdazian
01:20 PM Software Development: RE: Debugging DSP side with CCS_3.3
Rich,
I am attaching the CCS version information window from help->about.
!CCSVersionInfo.png!
I just tried ...
Michael Williamson
01:08 PM Software Development: RE: Debugging DSP side with CCS_3.3
Hi Mike,
Ok, that doesn't seem to work. I downloaded the update version to install CCS 3.3 v12 and when I ran the up...
Rich Bagdazian

08/02/2010

06:39 PM Software Development: RE: Debugging DSP side with CCS_3.3
HI Mike,
I just found out I need to be running release 12 of CCS and I'm on release 11 so I'm going to upgrade and s...
Rich Bagdazian
06:14 PM Software Development: RE: Debugging DSP side with CCS_3.3
Are you using the latest version of CCS 3.3?
Can you connect to the DSP while at a u-boot prompt (without the DSPL...
Michael Williamson
05:48 PM Software Development: Debugging DSP side with CCS_3.3
Hi Mike,
I got the CCS configuration setup as far as I can tell correctly using the platform configuration file fo...
Rich Bagdazian
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)