Activity
From 08/03/2010 to 09/01/2010
08/31/2010
- 07:06 PM Software Development: RE: Audio help needed
- Hi Mike,
Thank you for the information.
Once the drivers exist -- would you know what API I should probably be... - 05:20 PM Software Development: RE: Audio help needed
- Hello Mr. Schlunk,
Unfortunately, in order to use the audio output a new sound "board/driver" needs to be written ... - 04:08 PM FPGA Development: RE: FPGA Unused Pins
- Thanks
- 03:47 PM FPGA Development: RE: FPGA Unused Pins
- Hi John,
In general, you should tri-state / float all unused pins on the FPGA. This will result in those pins beh... - Did you have to do anything special to the unused EMIFA pins like
I_EMA_CS0_N
I_EMA_CS3_N
I_EMA_CS5_N
I_EMA_CAS... - 04:05 PM FPGA Development: RE: Digital DNA
- Yes but I think the range of the DNA value is assigned per customer so each customer has a unique set of values and n...
- 03:53 PM FPGA Development: RE: Digital DNA
- Stuff you probably already know, but:
According to our distributor, the Xilinx DNA code is unique per chip (like a...
08/30/2010
- I'm trying to figure out a simple method of getting a sound file to play on the board from our app.
After looking ... - 02:36 PM FPGA Development: RE: Accessing the FPGA Memory space using U-boot
- Hey I figured it out so never mind. the FPGA is at 0x6000000 and the memory commands in Uboot seem to work.
- I sent this messge to our software guys also but if youcan help it would be appreciated.
In order to debug the F... - 01:37 PM FPGA Development: RE: Digital DNA
- We do no need it on the MityDSP board I was just curious. We are using it on our PROBE FPGA. If you had one assigne...
08/27/2010
- 03:37 PM FPGA Development: RE: Digital DNA
- Hi John,
We're still looking into this here (I wanted to at least get you some feedback that someone saw your post...
08/26/2010
- Did you get a digital DNA value assigned for your FPGA's?
08/24/2010
- 09:11 PM FPGA Development: RE: POWER DOWN Memory Corruption
If your application will not be writing to the NAND flash then you should not need hold-up circuit from the motherb...- 09:04 PM FPGA Development: RE: POWER DOWN Memory Corruption
- So do you think we need to put on our mother board a circuit to hold up the power and interrupt the OMAP to let it kn...
- 08:58 PM FPGA Development: RE: POWER DOWN Memory Corruption
- John -
We are indeed aware of this and are working on a solution. We plan to allow for the root file system to be... - Software guys tell me they had a case where the FLASH memory was corrupted when the power was removed at the wrong ti...
- 06:51 PM FPGA Development: RE: Programming the FPGA
Hi John.
It looks like you are generating the .BIN file using the bitgen tool ("Generate Programming File" step ...- 04:00 PM FPGA Development: RE: Programming the FPGA
- Here is the .BGN but there were no .CFI or .PRM files in the FPGA directory.
- 03:44 PM FPGA Development: RE: Programming the FPGA
Hi John.
Would you be able to upload the .BGN .CFI & .PRM files that go with the .BIN file you have already uplo...- We are using the MityDSP-L138. Our software guys are not able to program my FPGA bin file using your routine. Your ...
08/23/2010
- 02:34 PM Software Development: RE: Rescanning the Nand flash
- Dennis,
Just so you know, the suggestions below are not based on personal experience.
Not sure there is a comma... - I made a type-o when loading the Nand flash. I managed to convince the flash that it has a whole bunch of bad areas. ...
08/18/2010
- 04:16 PM Software Development: RE: Loading FPGA
- Yes it is an industrial i/o board. That file did load, the light did come on. I need to tell the fpga guys they gave ...
- 03:46 PM Software Development: RE: Loading FPGA
- If you are using the Industrial I/O board Critical Link provided, try using the file attached below. This file is kn...
- 03:35 PM Software Development: RE: Loading FPGA
- Sorry about the typo-s. My email/web machine doesn't have a serial port so I've got an old laptop running the hyperte...
- 03:16 PM Software Development: RE: Loading FPGA
- On the tftp, what is the reported size of the transfer? Something like 0x71544 is expected. If the data is not the ri...
- 03:08 PM Software Development: RE: Loading FPGA
- I did tftp: 0xC0700000 192.168.1.118:fpga.bin
got the ### marks
Did
loadfpga 0xC07000000
no light, message "... - 02:58 PM Software Development: RE: Loading FPGA
- Yes, the "done" LED should light up when the FPGA is programmed correctly.
Can you include the set of commands you... - 02:51 PM Software Development: RE: Loading FPGA
- Should the "done" LED light up if the FPGA was programmed correctly?
- 02:39 PM Software Development: RE: Loading FPGA
- Dennis,
You are correct that the write command is missing the offset.
In the setenv command, the read is corre... - I've tried loading the FPGA. I didn't write the FPGA code, I'm just trying to load an fpga.bin file that I've been gi...
08/09/2010
- 08:57 PM Software Development: RE: Kernel documentation
- Interrupt number 91 (aka IRQ_DA850_RPIINT) works. It works, when I queue a DMA write I get an interrupt when it is co...
- 08:40 PM Software Development: RE: Kernel documentation
- The information you are looking for is in the "OMAP-L138 System Reference Guide":http://www.ti.com/litv/pdf/sprugm7d,...
- 03:50 PM Software Development: RE: Kernel documentation
- Building the uPP driver. I need to register and interrupt service routine.
To do that I need to know the irq number ...
08/03/2010
- 01:41 PM Software Development: RE: Debugging DSP side with CCS_3.3
- HI Mike,
Here is my about dialog:
!cc3about.png!
When I tried to update to 3.3.82 the installer told me I didn... - 01:20 PM Software Development: RE: Debugging DSP side with CCS_3.3
- Rich,
I am attaching the CCS version information window from help->about.
!CCSVersionInfo.png!
I just tried ... - 01:08 PM Software Development: RE: Debugging DSP side with CCS_3.3
- Hi Mike,
Ok, that doesn't seem to work. I downloaded the update version to install CCS 3.3 v12 and when I ran the up...
Also available in: Atom
Go to top
