Project

General

Profile

Activity

From 08/26/2014 to 09/24/2014

09/23/2014

02:05 PM Software Development: RE: UPP problem
Problem was caused by cache incoherency. Use of BCACHE_inv() fixed it. stephan berner

09/22/2014

10:19 AM Software Development: RE: USB Bug
There are several missing features in the 3.14 branch that I found when trying to move to it. I created a tag to mark... Jonathan Cormier
10:13 AM Software Development: RE: USB Bug
Note that we have seen a similar issue on the 335x. Could you checkout the following page and report back if the solu... Jonathan Cormier
10:11 AM Software Development: RE: USB Bug
It is from your git page - as far as I remember. Our software student tried to jump to 3.14 two month ago but it didn... Benedikt K.
09:39 AM Software Development: RE: USB Bug
Hello,
Are you using a 3.7 branch from our git site, or the mainline? I don't think we officially support 3.7. D...
Michael Williamson
09:37 AM Software Development: RE: USB Bug
Another thing: When I plug in the first usb device the number of usb interrupts in /proc/interrupts increases. When I... Benedikt K.
09:22 AM Software Development: USB Bug
Hej hej,
we have noticed a usb bug on the MityDSP and we are not sure why this happens.
We are using linux 3.7....
Benedikt K.

09/21/2014

02:51 PM Software Development: UPP problem
hi,
I am having problems reading data from the FPGA to memory. I set up the UPP interface
using channel A from t...
stephan berner

09/18/2014

10:07 AM FPGA Development: RE: Mity L138F FPGA -> OMAP interrupt lines
Thanks Mike,
I have found the pin mapping for INT0 and INT1 I couldn't find the mapping for the Non Maskable Inte...
Christopher Brunson
09:48 AM FPGA Development: RE: Mity L138F FPGA -> OMAP interrupt lines
Hi Chris,
The information you need is in Table 4 of the "Carrier Board Design Guide":http://www.criticallink.com/w...
Michael Williamson
09:36 AM FPGA Development: Mity L138F FPGA -> OMAP interrupt lines
I was trying to use an FPGA interrrupt which should be serviced by the DSP core in the OMAP.
From the MityL138.ucf...
Christopher Brunson

09/16/2014

09:55 AM Software Development: RE: Adding SPI flash
The part works in SPI mode 0 or 3, but I tried all four modes (0 - 3). I also tried setting the fields .c2tdelay and... Mary Frantz
09:45 AM Software Development: RE: Adding SPI flash
Is the SPI mode field correct (polarity and phase, CPOL and CPHA is the part in SPI_MODE_0)?
You also look like y...
Michael Williamson
09:06 AM Software Development: RE: Adding SPI flash
I confirmed with a scope that the chip select was not active.
I added DA850_GPIO2_15 to the the array of gpios in ...
Mary Frantz

09/12/2014

09:19 AM Software Development: RE: Adding SPI flash
It would not apply (different driver, different logic handling platform arguments). Michael Williamson
09:17 AM Software Development: RE: Adding SPI flash
Note that if you want to use the hardware designated chip select for that spibus instead of a gpio then the SPI_INTER... Jonathan Cormier

09/11/2014

06:18 PM Software Development: RE: Adding SPI flash
Hi Mary,
Have you configured the pin-mux for the DA850_GPIO2_15, which would correspond to the chip select you are...
Michael Williamson
01:20 PM Software Development: Adding SPI flash
We have a SPI serial flash device on our board, an M25PE80. It is connected to SPI1 with SPI1_CS1.
I created a ba...
Mary Frantz

09/10/2014

01:46 PM Software Development: RE: DSP HelloWorld Message Queue Buffer Length
Thanks for the clarification on the message handler code, and the message structure recommendation.
It definitely w...
Doug Browning
11:01 AM Software Development: RE: DSP HelloWorld Message Queue Buffer Length
Doug,
As far as I understand the anLength is really the length of the buffer passed between the DSP and ARM and is...
Jonathan Cormier
10:01 AM Software Development: DSP HelloWorld Message Queue Buffer Length
I'm modifying the DSP HelloWorld example code from the Wiki site to transfer data types other than strings (see SW Fo... Doug Browning

09/02/2014

08:33 AM Software Development: RE: How to probe the fpga_ctrl & fpga_gpio.ko module
Have you made any progress with this problem? Jonathan Cormier
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)