Project

General

Profile

Activity

From 12/18/2017 to 01/16/2018

01/16/2018

03:18 PM Software Development: RE: IPC and uPP interrupts APIs conflict
Hi Okan,
I'm not too familiar with either syslink or starterware. However I've found that when I'm debugging kerne...
Jonathan Cormier
12:42 PM Software Development: RE: IPC and uPP interrupts APIs conflict
Hi Greg,
I've already read the relevant sections of the technical reference manual and megamodule reference guide,...
Okan Çalış

01/15/2018

04:03 PM Software Development: RE: IPC and uPP interrupts APIs conflict
Hi Okan,
My guess is that your core problem is that SysLink and StarterWare simply do not play well together in g...
Gregory Gluszek
05:51 AM Software Development: RE: IPC and uPP interrupts APIs conflict
Hello again,
I've just realized the line "@ISTP = (unsigned int)_intcVectorTable;@" in @{StarterWare}/system_confi...
Okan Çalış

01/12/2018

02:07 PM Software Development: RE: Linux USB Gadget is not working on custom board
Glad it worked. I suspect your ID pin is being pulled low somehow. But as long as you don't need to support HOST mo... Jonathan Cormier
10:23 AM Software Development: RE: Linux USB Gadget is not working on custom board
Jonathan Cormier wrote:
> In the 3.2 branch Peripheral mode can be configured in the baseboard.
That actually w...
Okan Çalış

01/11/2018

02:13 PM Software Development: RE: Linux USB Gadget is not working on custom board
Okan Çalış wrote:
> Michael Williamson wrote:
>
> > Do you see these lines even if you don't connect the PC? (I ...
Jonathan Cormier
08:47 AM Software Development: RE: Linux USB Gadget is not working on custom board
Michael Williamson wrote:
> Do you see these lines even if you don't connect the PC? (I was looking to see if the...
Okan Çalış

01/10/2018

02:37 PM Software Development: RE: Linux USB Gadget is not working on custom board
Could you attach your .config?
By default, CONFIG_USB_MUSB_OTG is selected which puts the kernel in OTG mode. In ...
Jonathan Cormier
01:27 PM Software Development: RE: Linux USB Gadget is not working on custom board
> Do you see these lines even if you don't connect the PC?
Yes, I see those lines even when not connected to the h...
Okan Çalış
01:06 PM Software Development: RE: Linux USB Gadget is not working on custom board
So if you are trying to run in peripheral mode, I am not entirely sure I understand the last lines of your log file:
...
Michael Williamson
12:45 PM Software Development: RE: Linux USB Gadget is not working on custom board
Hi Mike,
> Are you using USB as OTG? Host or peripheral mode for your test?
In our tests, the device acts as t...
Okan Çalış
12:13 PM Software Development: RE: Linux USB Gadget is not working on custom board
Are you using USB as OTG? Host or peripheral mode for your test?
If you do a dmesg (before and after plugging in ...
Michael Williamson
11:37 AM Software Development: Linux USB Gadget is not working on custom board
Hi,
We've been working on a MityDsp-L138F SoM and so far managed to use USB GadgetFS feature of the Linux kernel t...
Okan Çalış

01/09/2018

01:37 PM Software Development: IPC and uPP interrupts APIs conflict
Hi,
We've been working on a MityDsp-L138F. The ARM and DSP cores run Linux and SYS/BIOS, respectively. We're using...
Okan Çalış

01/04/2018

02:06 PM Software Development: Real time signal input and output with uPP interface in MityDSP
Hi,
I have a custom board with
1) MityDspl-138F module (with FPGA)
2) No Ethernet port
3) UART,USB,SD CARD int...
Vivek Ponnani

12/27/2017

09:57 AM Software Development: RE: Changing UART1 to UART2 in Linux Kernel
Just noticed I left the @bootargs@ as @ttyS1@.
Changing that to @ttyS2@ solved that issue.
Sorry, I wasn't expectin...
Okan Çalış
05:32 AM Software Development: Changing UART1 to UART2 in Linux Kernel
Hi,
We've been working on a MityDsp-L138F board, and I can boot to Linux with NFS, with the following environment va...
Okan Çalış

12/21/2017

11:56 AM Software Development: Low frequency input (5 Hz to 20KHz processing) for mitydspl138F
Hi,
I have a custom board with
1) MityDspl-138F module (with FPGA)
2) No Ethernet port
3) UART,USB,SD CARD int...
Vivek Ponnani
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)