Activity
From 01/08/2018 to 02/06/2018
02/06/2018
- 03:08 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- Okan Çalış wrote:
> But this is our custom board. What should I enter in those fields?
This is the factory config... - 02:57 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- But this is our custom board. What should I enter in those fields?
- 02:38 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- > MityOMAPL138: Read Factory Config Failed: -110
This line is very concerning. It appears you have erased or corrup... - 05:58 AM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- Hi Jonathan,
> Your u-boot and kernel partitions don't seem to match.
I changed the file @board-mityomapl138.c... - 10:14 AM FPGA Development: RE: FPGA Done led not turning on with CPU programming
- Michael Williamson wrote:
> How are you generating the bin file?
>
> Check this "wiki page":https://support.criti... - 10:11 AM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> >
> > 1)When application runs,there is some debug part (as above...
02/05/2018
- 04:31 PM Software Development: RE: Using McASP Rx clock generation module
- Ideally you should get it working from the baseboard as that should be the source of all the pinmux settings. Not su...
- 04:12 PM Software Development: RE: Using McASP Rx clock generation module
- Hi Jonathan,
Ok, good suggestion... thanks... the pinmux read
PINMUX0 = 0x8811.1110
so it's not getting set... - 02:40 PM Software Development: RE: Kernel panics on custom board: "No init found. Try passing init= option to kernel"
- Your u-boot and kernel partitions don't seem to match. Also asuming the u-boot partitions scheme is the correct one, ...
- Hi,
As some of you may know, I've been working on a MityDsp-L138F SoM, and I also have a custom designed board bas...
02/02/2018
- 06:57 PM Software Development: RE: Using McASP Rx clock generation module
- Can you dump the pinmux registers so we can double check them?
0x01C14120 - PINMUX0
0x01C14124 - PINMUX1
02/01/2018
- 09:59 PM Software Development: RE: Using McASP Rx clock generation module
- Hi Mike, thanks for responding.
So I have updated the baseboard-industrialio.c to enable all of the baseboard_mca... - 09:32 PM Software Development: RE: Using McASP Rx clock generation module
- Hi Tom,
Have you checked the pinmux settings for the IO Pin are set to use the McASP function and not GPIO or some... - 09:24 PM Software Development: RE: Using McASP Rx clock generation module
- Hi,
We are working thru enabling of the McASP Rx clock generator module. After making source updates to davinci_m...
01/31/2018
- 02:42 PM FPGA Development: RE: FPGA Done led not turning on with CPU programming
- How are you generating the bin file?
Check this "wiki page":https://support.criticallink.com/redmine/projects/arm9... - Hi,
We have made our own customized board uing the Industrial IO Board and the Analog expansion board.
We were pr...
01/30/2018
- 07:01 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
>
> 1)When application runs,there is some debug part (as above)which dsp sends to arm with ds... - 06:13 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- I was expecting following Debug response, which comes up when I run application by myself with the help of treaterm a...
- 03:16 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> > > 2) FPGA write in SPI Flash
> > > U-Boot > setenv bootcmd "run programfpga"
> > You appe... - 02:48 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> > I followed the suggestions and tried to boot from flash. But It ...
01/29/2018
- 04:44 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> I followed the suggestions and tried to boot from flash. But It still does not run applicatio... - 03:25 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- I followed the suggestions and tried to boot from flash. But It still does not run application automatically. Below i...
- Hi,
We are developing a new codec using the MityDSP. So the Industrial IO has the DSD1791 audio DAC on it's McASP....
01/25/2018
- 09:24 PM Software Development: RE: SYS/BIOS
- Finally i could solve this issue by adding the following code :
asm(" mrc p15, #0, r0, c1, c0, #0\n\t"
" orr r0, ...
01/24/2018
- 07:47 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Jonathan Cormier wrote:
> > Vivek Ponnani wrote:
> > > Thanks for your response. It is very... - 05:13 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Jonathan Cormier wrote:
> Vivek Ponnani wrote:
> > Thanks for your response. It is very helpful.
> >
> > Most of... - 03:59 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Thanks for your response. It is very helpful.
>
> Most of the points are cleared. I have f... - 02:24 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Thanks for your response. It is very helpful.
Most of the points are cleared. I have further queries as below.
...
01/23/2018
- 02:51 PM Software Development: RE: Auto run of application file (loaded in NAND Flash)
- Vivek Ponnani wrote:
> Hi,
>
> I have a custom board with
> -- MityDspl-138F module (with FPGA)
> -- No Ethern... - Hi,
I have a custom board with
-- MityDspl-138F module (with FPGA)
-- No Ethernet port
-- UART,USB,SD CARD int... - Hello Forum,
i have a question related to usage of TI SYS/Bios on MiTyDSP without FPGA.
i successsfull flashed my a...
01/18/2018
- 11:51 AM Software Development: RE: uPP on MityDsp
- Hello Greg,
many thanks for your answers.
I will try that configuration, takes a while.
Great Support Many Thank...
01/17/2018
- 06:06 PM Software Development: RE: uPP on MityDsp
- Hi Martin,
LCD [8] - LCD [15] also function as Boot Mode Selection pins. The SN54LVC157A is used to change the pu... - 04:27 PM Software Development: RE: uPP on MityDsp
- Hello Greg,
many thanks for your answer.
as i Know LCD[x] pins are outputs. and on the MityDsp is see U9 which is a... - 04:05 PM Software Development: RE: uPP on MityDsp
- Hi Martin,
I have never personally used the uPP in this setup, however, it looks like it should be possible.
... - I have a question for clarification.
We want to use MityDsp without FPGA and use both uPP-Channels as Input.
Is tha...
01/16/2018
- 03:18 PM Software Development: RE: IPC and uPP interrupts APIs conflict
- Hi Okan,
I'm not too familiar with either syslink or starterware. However I've found that when I'm debugging kerne... - 12:42 PM Software Development: RE: IPC and uPP interrupts APIs conflict
- Hi Greg,
I've already read the relevant sections of the technical reference manual and megamodule reference guide,...
01/15/2018
- 04:03 PM Software Development: RE: IPC and uPP interrupts APIs conflict
- Hi Okan,
My guess is that your core problem is that SysLink and StarterWare simply do not play well together in g... - 05:51 AM Software Development: RE: IPC and uPP interrupts APIs conflict
- Hello again,
I've just realized the line "@ISTP = (unsigned int)_intcVectorTable;@" in @{StarterWare}/system_confi...
01/12/2018
- 02:07 PM Software Development: RE: Linux USB Gadget is not working on custom board
- Glad it worked. I suspect your ID pin is being pulled low somehow. But as long as you don't need to support HOST mo...
- 10:23 AM Software Development: RE: Linux USB Gadget is not working on custom board
- Jonathan Cormier wrote:
> In the 3.2 branch Peripheral mode can be configured in the baseboard.
That actually w...
01/11/2018
- 02:13 PM Software Development: RE: Linux USB Gadget is not working on custom board
- Okan Çalış wrote:
> Michael Williamson wrote:
>
> > Do you see these lines even if you don't connect the PC? (I ... - 08:47 AM Software Development: RE: Linux USB Gadget is not working on custom board
- Michael Williamson wrote:
> Do you see these lines even if you don't connect the PC? (I was looking to see if the...
01/10/2018
- 02:37 PM Software Development: RE: Linux USB Gadget is not working on custom board
- Could you attach your .config?
By default, CONFIG_USB_MUSB_OTG is selected which puts the kernel in OTG mode. In ... - 01:27 PM Software Development: RE: Linux USB Gadget is not working on custom board
- > Do you see these lines even if you don't connect the PC?
Yes, I see those lines even when not connected to the h... - 01:06 PM Software Development: RE: Linux USB Gadget is not working on custom board
- So if you are trying to run in peripheral mode, I am not entirely sure I understand the last lines of your log file:
... - 12:45 PM Software Development: RE: Linux USB Gadget is not working on custom board
- Hi Mike,
> Are you using USB as OTG? Host or peripheral mode for your test?
In our tests, the device acts as t... - 12:13 PM Software Development: RE: Linux USB Gadget is not working on custom board
- Are you using USB as OTG? Host or peripheral mode for your test?
If you do a dmesg (before and after plugging in ... - Hi,
We've been working on a MityDsp-L138F SoM and so far managed to use USB GadgetFS feature of the Linux kernel t...
01/09/2018
- Hi,
We've been working on a MityDsp-L138F. The ARM and DSP cores run Linux and SYS/BIOS, respectively. We're using...
Also available in: Atom
Go to top
