Mity CPU Platforms » MitySOM-335x (ARM Cortex-A8 Based Products)

10/11/2012

08:18 PM PCB Development: RE: Recommended PHY for RGMII

Hi Mark,
We just kitted a build for DevKits and were able to get the VSC8601 less than a week ago, however I do se... Michael Williamson

04:55 PM PCB Development: Recommended PHY for RGMII

I have recently begun a design-in of the 3359 module to an existing product. I am at a point where I will address the... Mark Kraft

11:10 AM PCB Development: RE: Evaluation kit schematic - as Design reference

Thanks Mark Kraft

10:30 AM PCB Development: RE: Evaluation kit schematic - as Design reference

Did you find the schematics for the DevKit board? They are posted "here":http://support.criticallink.com/redmine/proj... Michael Williamson

09:14 AM PCB Development: Evaluation kit schematic - as Design reference

Hi,
I have just begun implementing the 3359 module into an existing design, to replace another manufactures obsole... Mark Kraft

10/04/2012

09:11 AM Software Development: RE: Ethernet Interface to Micrel KSZ9021 PHY.

Hi Raja,
I don't think we've used this PHY with the MityARM-3359 here, but we have had problems strapping this dev... Michael Williamson

10/03/2012

03:31 PM Software Development: Ethernet Interface to Micrel KSZ9021 PHY.

Hi,
We are using MityARM SOM and MICREL KSZ9021RNI gigabit as PHY on it for Ethernet Interface.
We have configure... Raja Vankam

10/01/2012

12:22 PM PCB Development: RE: Caution on MityARM SO-DIMM PCB Footprint

Mark,
Thank you for pointing out that lack of information. It has now been addressed and the design guide has been... Alexander Block

07:40 AM PCB Development: RE: Ethernet PHYs

Hi Mark,
I don't see a way around this at the moment. It does indeed look like you need to use the Gigabit Phy in... Michael Williamson

09/30/2012

05:34 PM PCB Development: RE: Ethernet PHYs

Hi Mark,
You are correct about the PR1_MII* signals, according to this E2E post, sorry about that.
http://e2e.t... Michael Williamson

09/28/2012

11:57 AM PCB Development: RE: Ethernet PHYs

Hi Mike,
The interfaces we definitely need out of the 335x are a 16 bit GPMC (to FPGA), 1 Ethernet (10/100 is fine... Anonymous

09:35 AM PCB Development: RE: Ethernet PHYs

What other peripherals are you trying to accommodate? At a glance it looks like the pin outs should support RMII0 on... Michael Williamson

08:49 AM PCB Development: Ethernet PHYs

Please correct me if I'm wrong, but it appears the pin-muxing configuration for the MityARM-335x SOM is forcing the u... Anonymous

08:26 AM PCB Development: Caution on MityARM SO-DIMM PCB Footprint

The PCB footprint found in section 6.5 of the MityARM-335x Carrier Board Design Guide can be misleading if you are no... Anonymous

09/26/2012

10:10 AM PCB Development: RE: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector

We have not tested such a configuration, so I don't really know. If the electrical connections honor the spec, then ... Michael Williamson

09/24/2012

03:12 PM PCB Development: MityARM standard-keyed vs. reverse-keyed SO-DIMM connector

The MityARM design guide suggests an SO-DIMM connector with a standard keying. We have built our board with a revers... Ali Asgar Sohanghpurwala

09/21/2012

10:11 AM Software Development: RE: MityARM-335x Ethernet Communication

Found the problem. The problem was related to the errata on the Vitesse VSC8601 Ethernet phy used on the development... Anonymous

09/20/2012

09:49 AM Software Development: MityARM-335x Ethernet Communication

I am trying to get the TI StarterWare Enet_Echo example to run on the MityARM-335x Development Kit. To accomplish thi... Anonymous

09/18/2012

04:36 PM Software Development: RE: mod_fastcgi.so

Hi Scott,
Tried that with no luck...
however I was looking through the lighttpd documentation and saw I forgot t... R D

02:45 PM Software Development: RE: mod_fastcgi.so

Try "--host=arm-angstrom-linux-gnueabi" instead....
-Mike
Michael Williamson

02:30 PM Software Development: RE: mod_fastcgi.so

Scott,
Downloaded from:
http://download.lighttpd.net/lighttpd/releases-1.4.x/
lighttpd-1.4.26.tar.gz 2010-Feb-07... R D

12:38 PM Software Development: RE: mod_fastcgi.so

Randy,
Could you give me a link to where you downloaded the lighttpd source? Also once you downloaded it, can you ... Scott Gerenser

09:41 AM Software Development: RE: mod_fastcgi.so

Hi Mike,
I found out the version of the lighttpd based on one of the included shared libraries.
I have downloaded... R D

09/17/2012

10:57 AM Software Development: RE: mod_fastcgi.so

Hi Mike,
Should have mentioned Linux and Lighttpd are very new for me.
I had assumed I could just compile the light... R D

09/15/2012

06:36 AM Software Development: RE: mod_fastcgi.so

So anyway, the mod-fastcgi.so should not require you to rebuild the kernel. You should be able to download it, "conf... Michael Williamson

09/14/2012

12:54 PM Software Development: RE: mod_fastcgi.so

What filesystem are you using? You might be able to get it installed using opkg.
-Mike
Michael Williamson

12:14 PM Software Development: mod_fastcgi.so

Hi,
I'm trying to use fastcgi with the lighttpd web server. I have successfully create a simple example and changed ... R D